2008 Citroen C4 PICASSO DAG seats

A
B
12
114
III
LONGITUDINAL ADJUSTMENT
Lift the control A, located at the front of the seat, then adjust the seat into the position desired.
THE “COMFORT” POSITION
The 3 second-row seats are inde-pendent of each other and all the same width. They all can have a “comfort” position.
To place the seat(s) in the comfort position
- Pull on the control B.
The backrest reclines and the seat base pivots slightly.
To return the seat to the initial position
- Pull on the control B and allow the seat to come forwards.
IMPORTANT : Always supervise any movements of seats by children.
REAR HEAD RESTRAINTS
The rear head restraints have two possible positions :
1. a low position for when the seats are not occupied,
2. a high position to ensure pas-senger safety, by raising the restraints to their locking posi-tion.
To lower the head restraints
- Press on the unlocking button.
- Press on the top of the head restraint.
To raise the head restraints
- Pull the head restraint upwards as far as it will go.
- Press on the unlocking button and pull the head restraint up-wards.
S E C O N D R O W S E A T S

C
III
115
Each seat can be folded onto the fl oor to enable you to modify your vehicle’s interior space.
TO FOLD THE SEATS
- Pull fi rmly upwards on strap C, as indicated by the red arrow, to unlock the seat ; maintain the pressure until the seat is fully folded.
- Push the backrest slightly forwards so that the back-rest pivots, folding onto the seat base. The assembly then lowers onto the fl oor.
TO RETURN THE SEATS TO THE UPRIGHT
POSITION
Raise the backrests and push them rearwards so that they lock in position
PLATES BEHIND THE SECOND ROW
SEATS
Plates below the second row seats provide the bottom of the bootspace with rigidity. They automatically fol-low the seat movements (e.g. longitudinal adjustment, folding).
A storage area is available underneath the plates.
IMPORTANT : Always supervise any movements of seats by children.
S E C O N D R O W S E A T S C 4 P I C A S S O

A
B
12
114
III
LONGITUDINAL ADJUSTMENT
Lift the control A, located at the front of the seat, then adjust the seat into the position desired.
THE “COMFORT” POSITION
The 3 second-row seats are inde-pendent of each other and all the same width. They all can have a “comfort” position.
To place the seat(s) in the comfort position
- Pull on the control B.
The backrest reclines and the seat base pivots slightly.
To return the seat to the initial position
- Pull on the control B and allow the seat to come forwards.
IMPORTANT : Always supervise any movements of seats by children.
REAR HEAD RESTRAINTS
The rear head restraints have two possible positions :
1. a low position for when the seats are not occupied,
2. a high position to ensure pas-senger safety, by raising the restraints to their locking posi-tion.
To lower the head restraints
- Press on the unlocking button.
- Press on the top of the head restraint.
To raise the head restraints
- Pull the head restraint upwards as far as it will go.
- Press on the unlocking button and pull the head restraint up-wards.
S E C O N D R O W S E A T S

C
D
E
A
116
III
Each seat can be folded onto the fl oor to form a fl at surface, thus enabling you to modify your vehi-cle’s interior space.
TO FOLD THE SEATS
From the exterior
- Pull fi rmly upwards on strap C, as indicated by the red arrow, to unlock the seat ; maintain the pressure until the seat is fully folded.
- Push the backrest slightly for-wards, so that the backrest piv-ots, folding onto the seat base. The assembly will then lower onto the fl oor.
From the boot (in the loading situation, for example)
You can fold the second-row seat(s) from the boot, having fi rst folded the third-row seats.
- Pull on the control D to unlock the chosen seat, push the back-rest gently forwards.
TO RETURN THE SEATS TO
THE UPRIGHT POSITION
1. Return the second-row seat bases to their initial position and lock them in that position.
2. Raise the backrests and push them rearwards so that they lock in position.
To unlock / lock the rigid plate :
- Slide the latch A on the plate downwards, to unlock.
- Return the plate to the upright position, then slide the latch Aupwards, to lock.
Note : Before deploying the rigid plates, check that the second-row seats are slid as far as possible rearwards. 5-seater confi gurations do not have these rigid plates.
RIGID PLATE
Each second-row seat backrest has a rigid plate attached.
This plate enables you :
- to have a continuous load surface in the boot, whatever the positions of the seats,
- to avoid having objects sliding un-der the second-row seats.
Before moving the third-row seats, return the second-row rigid plates to their initial posi-tion and lock them.
Emergency exit : Should the fi rst system fail (control C), the control D is available for use by third-row passengers to accel-erate their exit.
IMPORTANT : Always super-vise any movements of seats by children.
S E C O N D R O W S E A T S G R A N D C 4 P I C A S S O

E
III
117
“CINEMA SEAT” POSITION
This position allows you to free up space between the fi rst row and the second row.
Pull the control E under the seat.
Note : This position is only possible with the lateral seats.
ACCESS TO THE THIRD ROW SEATS
The third-row seats can be accessed via the lateral second-row seats.
1. Pull the control E. The seat un-locks and the seat base comes up against the backrest.
2. Hold the control E in the raised position, pushing forwards. The whole slides towards the front seat.
3. Raise and lock the rigid plate.
Space becomes free behind the seat, the third-row passengers can get to their seats.
To exit the third-row seat positions :
1. Hold the control E in the raised position. The seat unlocks and the seat base comes up against the backrest.
2. Push the seat backrest, still holding the control E in the raised position.
Note : if the table on the back of the fi rst-row seat is down, close it to enable this operation.
Repositioning the seat,
from the exterior,
with the door open
If there are passengers seated in the third row :
1. Manually return the assembly as far as possible rearwards. The seat does not return as far as the maximum rearwards position, so as to retain leg space for the third-row pas-sengers.
2. Fold the seat base.
S E C O N D R O W S E A T S G R A N D C 4 P I C A S S O

1
2
3
G
F
118
III
CONCERTINA PLATES
Two rigid concertina plates, which cannot be separated from the ve-hicle, cover the 2 third-row seats, when these are in the folded posi-tion.
To fold the concertina plates :
Pull on the control, the 3 sections of the plate will fold like a concer-tina.
When the third-row seats are up-right, these concertina plates can be left either :
- fl at behind the seats,
- in the vertical position,
thereby leaving a storage area available.
TO RETURN THE SEATS TO
THE UPRIGHT POSITION
1. Return the second-row rigid plates to their initial position and lock them.
2. Having folded your concertina plate, pull on the control F lo-cated behind the seat back-rest. The backrest pivots rear-wards, pulling the seat base with it. The seat locks in the open position.
TO STOW THE SEATS
1. Return the second-row rigid plates to their initial position and lock them.2. Lower the head restraints.3. Correctly position the concer-tina plate vertically behind the seat.4. Pull on the control G located at the bottom of the seat back-rest. The seat unlocks.5. Next push the backrest gently forwards. The backrest pivots, folding onto the seat base. The seat base then folds into the stowage area provided for that purpose.6. Reposition the concertinaplates over the folded seats.
Before moving the third-row seats, return the rigid plates of the second-row seats to the upright position and lock them.
Do not try to fold a third-row seat that has not fi rst had the backrest fully locked in place.
Do not leave objects either on or underneath the seat bases of the third-row seats when you are folding them.
Do not leave your hand on the control G as you fold the seats, as you risk trapping your fi ngers.
T H I R D R O W S E A T S G R A N D C 4 P I C A S S O

III
119
A Lounge version is available in the 5 seater model. This has two se-cond-row seats that are identical to the fi rst-row seats, providing greater comfort for rear passengers.
ADJUSTING THE SEATS
The seats have the following adjust-ments :
- head-restraint adjustment,
- backrest angle,
- greater longitudinal adjustment,
- height-adjustable armrests.
Refer to the page « FRONT SEATS - Manual adjustments » for the operation of the adjustment controls.
LUGGAGE COVER BEHIND
THE SEATS
A fl exible luggage cover positio-ned behind the second-row seats enables you to prevent objects from sliding under or between the second-two seats, as well as concealing the contents of your boot from outside view.
It is fi xed to the fl oor by two hooks located behind the seats and an-chored at special points on the rear pillars.
This fl exible luggage cover is mo-vable and can be rolled up for stowage behind the second-row seats.
SEAT BELTS
For safety reasons, always attach your seat belt before positioning the armrest between yourself and the door.
STORAGE POCKETS
Two storage pockets are located on the insides of the Lounge ver-sion seats.
F E A T U R E S O F T H E 4 S E A T E R
L O U N G E V E R S I O N

120
III
S E A T B E L T S
Pyrotechnically pretensioned seat belts with force-limiters
In the event of a collision:
- The pretensioners pull back the front seat belts. The occupants are thus held more fi rmly against their seats.
- The force limiters reduce the pressure of the seat belt against the occupant’s chest, thus en-hancing the protection that the seat belt provides.
They must be replaced follow-ing a deployment, preferably by a CITROËN dealer or by an au-ing a deployment, preferably by ing a deployment, preferably by
thorised repairer.
Due to the safety regulations in force, any check or any re-placement should preferably be carried out by the CITROËN placement should preferably placement should preferably
network which guarantees the work and ensures that it is done correctly.
Any repair that is not done in strict compliance with require-ments could result in the sys-tems operating incorrectly or randomly, with the risk of bodily injuries being caused.
The driver must ensure that all of the passengers are correctly restrained by their seat belts.
To be effective, a seat belt must :
- Restrain a single person of adult size.
- Not bear any signs of being cut or frayed.
Never carry a child on your knees.
Do not swap buckles, as they would then not fulfi l their proper roles.
Never use clamps or clips to loos-en your seat belt.
Do not pass the seat belt over hard or breakable objects that you may have in your pockets.
If the seat has an armrest, the central part of the belt should pass underneath.
Before and after use, make sure that the belt is correctly retracted.
Regularly check the condition and cleanliness of the seat belts and attachments.
Have the seat belts checked pe-riodically by a CITROËN dealer Have the seat belts checked pe-belts checked
as well as after any accident, even a minor one.
The deployment of the preten-sioners is accompanied by a light discharge of harmless smoke and a noise, both due to the ex-plosive cartridges that activate them.
Depending on the nature and the force of the impact, this triggering of the pretensioners may happen prior to, and independently of, the deployment of the airbags.
In all cases, the warning lamp comes on.