Page 77 of 184
92
III
I N T E R I O R C O M F O R T
Lower glovebox
To open, pull the handle and lower the lid.
It comprises a storage area for vehicle documents.
Front seat drawers
To open, lift then pull towards the front.
Boot storage
Straps anchored to the boot aper-ture are provided for the securing of a wide variety of objects (e.g. doctor’s bag, warning triangle, oil container etc).
Further items can be stowed in the s t o r a g e a r e a fi t t e d i n t o t h e r i g h t hand side of the load area.
WARNING
As a safety measure, the glovebox must remain shut when the vehicle is in motion.
Page 80 of 184
21
1
12
4
4
3
95
III
M O D U B O A R D S H E L F
The Moduboard shelf, located at the rear of the benchseat backrests, enables the bootspace to be variously c o n fi g u r e d .
A - Shelf stowed vertically against the benchseat backrests.
Removing the parcel shelfHold it with one hand.
Unlock by pressing on the controls 1.Tilt the Moduboard shelf (still folded) towards you.
Release it from its mountings.
Handle the shelf without forcing the joints that link the various sections.Note: It is possible to fold the central retaining tab 2 between the seat backrests.
Fitting the shelf in placeunfold the central retaining tab 2 (the presence of this tab is essential for supporting weight).
present the shelf (folded) in a position tilted towards the mountings.lock it in the stowed position.
Locking the shelffold it.lock by engaging it in the controls 1.
Page 84 of 184
B
99
III
R E A R P A R C E L S H E L F
Removal
To remove it, detach the cords. Push up vertically, then lift on each side.
Storage areas
Tilt the shelf to stow it against the rear seats.
R e fi t t i n g
P r e s e n t t h e s h e l f t o i t s fi x i n g p o i n t s and push vertically until it is fully engaged.
To attach the shelf and tailgate, t a k e t h e c o r d s a n d fi x t h e m a t B
Do not place any hard or heavy item on the rear shelf.
These could be dangerous if thrown around during harsh braking or, if they touch the rear screen, could damage the heating elements.
Page 85 of 184
A
1
2
IV
100
B O N N E T R E L E A S E
Check that the bonnet is properly secured.
Avoid opening the bonnet in high winds.
Bonnet
This operation should only be performed while the vehicle is stationary.
To release the bonnet, pull the control located under the dash-board towards you.
Operate the lever A, located above the grille, to the right of the chevrons, then lift.Note: The panel may be hot after the vehicle has been in use.
Bonnet stay: Unclip and swivel the strut, to insert it in notch 1, then in notch 2.
Warning: Do not pull the strut towards the front.
To close
Lower the bonnet carefully, then let it drop shut.
Page 98 of 184
IV
114
F U S E S
Fuseboxes
There are two fuse boxes, one below the dashboard and one under the bonnet.
Dashboard fuses
The fuse box is located in the lower glovebox compartment. To access the fuses, open the glove box, pull the handle on the fuse box cover.
Replacing a fuse
Before replacing a fuse, you should ascertain the cause of the fault and have it remedied. The numbers of the fuses are indicated on the fusebox.
GoodBad
Pliers AReplace the fuse that has blown with one of the same rating (same colour).
Use the special pliers A stowed on the cover close to the fuseboxes, this includes a compartment for replacement fuses.
Page 104 of 184
120
V
C H A N G I N G B U L B S
Front direction indicator
Tilt the metallic spring holding the fl a p g i v i n g a c c e s s t o t h e l a m p bulbs.
O p e n t h e a c c e s s fl a p .
Rotate the bulb- holder a quarter turn and pull.
Take out the bulb.
Bulb: PY 21 W (yellow)
Sidelamp
Tilt the metallic spring holding the fl a p g i v i n g a c c e s s t o t h e l a m p bulbs.
O p e n t h e a c c e s s fl a p .
Rotate the bulb- holder a quarter turn and pull.
Bulb: W 5
Side repeater direction indicator
To change the direction indicator side repeater, push it forwards or rearwards to detach it, then pull it towards you.
Hold the cable and disconnect it.
Contact a CITROËN dealer.
Page 108 of 184
A
124
V
S A F E T Y R E C O M M E N D A T I O N S
Towbar
W e r e c o m m e n d y o u t o h a v e t h i s d e v i c e fi t t e d b y a C I T R O Ë N D e a l e r , w h o w i l l b e a c q u a i n t e d w i t h y o u r v e h i c l e ’ s towing capability and with the procedures necessary for installing a safety item of this kind.
Roof bars
For your safety and to avoid damage to the roof, you should u se roof bars that are tested and approved by AUTO-MOBILES CITROËN for the design of your particular vehicle.For your safety and to avoid damage to the roof, you should use safety and
Recommendations:Spread the load evenly, avoiding overloading on one side.
Position the heaviest weight as low down as possible.Tie the load down securely and add warning signs if it is protruding.
Drive conservatively, as the vehicle will be more vulnerable to si de winds.
The stability of your vehicle may be altered.
Remove the roof rack or roof bars when you are not using them.
Page 111 of 184
2
4
5
16
3
127
V
C H A N G I N G A W H E E L
Removal1. P a r k t h e v e h i c l e o n s t a b l e , fi r m g r o u n d t h a t i s n o t s l i p p e r y . A p p l y t h e parking brake. S w i t c h o f f t h e i g n i t i o n a n d e n g a g e fi r s t g e a r o r r e v e r s e g e a r , d e p e n d i n g on any slope.Ensure that all vehicle occupants have left the vehicle an d are positioned in a safe place.
2. Position the jack at one of the four jacking-points provided on the subframe close to the wheels. Using the handle, unwind the jack until it reaches the ground.3. To unclip the wheel embellisher, pull using the end of the wheelbrace as a lever in one of the apertures.For vehicles with aluminium wheel rims:
With a central embellisher, remove the embellisher, using the tool, to access the bolts.With wheel bolts visible, simply undo them.4. Continue to extend the jack until the wheel is a few centimetres off the ground.5. Undo the other bolts, remove the wheel.
-
-
Tools1. Jack2. Wheelbrace3. Central embellisher removing tool for accessing the wheel bolts (For vehicles with aluminium wheel rims).4. Socket for anti- theft bolts (For vehicles with aluminium wheel rims).5. Tool for removing wheel bolt protectors (For vehicles with alumin ium wheel rims).6. Movable towing eye.
