2008 Citroen C1 DAG key battery

2
23
AUDIO EQUIPMENT
GENERAL FUNCTIONS
On/off
With the ignition key in
the accessories posi-
tion or with the ignition on, press this
button to switch the audio equipment
on or off.

After the engine has been switched
off, the audio equipment can only op-
erate for approximately 30 minutes,
to prevent discharging of the battery.
Press the upper part
of this button several
times in succession to
increase the volume of
the audio equipment
or the lower part of this
button to decrease it.
VOLUME ADJUSTMENT
CLOCK ADJUSTMENT
Press this button sev-
eral times in succes-
sion to gain access
to the bass
(BASS) ,
treble (TREB) , front/rear balance

(FAD) and left/right balance (BAL)
settings.
AUDIO SETTINGS
Press this button for
more than 2 seconds,
the clock display
fl ashes:
AUXILIARY SOCKET
An auxiliary socket

"AUX" is provided for
the connection of port-
able equipment (MP3
player, etc.).
When the parameter
is displayed, change
the setting using these
two buttons.
You exit from this mode automati-
cally after a few seconds without any
action. In order to listen to it,
connect your equip-
ment then press this
button.
The audio equipment controls enable
you to adjust the volume and the audio
settings.
To exit from the AUX source, press

AM/FM .

When using an MP3 player: in-
crease the volume of the radio signifi -
cantly (between 30 and 60) to obtain
a satisfactory playing volume.
- t o adjust the hours, press this button,
- to adjust the minutes, press this
button.
You exit from this mode automati-
cally after a few seconds without any
action.

4
47
ACCESS
IMMOBILISER This locks the engine control sys-
tem as soon as the ignition has been
switched off and therefore prevents
starting of the vehicle by anyone who
does not have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code
must be recognised for starting to be
possible.
In the event of a malfunction, your
vehicle will not start.
Consult a CITROËN dealer.
Changing the remote control
battery
To change the battery, remove the
screw then unclip the housing using
a coin inserted at the ring.
Battery CR 2016/3 volts.
If the remote control does not work
after the battery has been changed,
reprogramme it. Reprogramming the remote
control
Following replacement of the remote
control battery or in the event of a re-
mote control malfunction, it may be
necessary to reprogramme the sys-
tem.

 Switch off the ignition.

 Switch the ignition on again.

 Press one of the remote control
buttons immediately for a few se-
conds.

 Switch off the ignition and remove
the key from the ignition lock.
The remote control is now working
again.
If the malfunction persists, contact a
CITROËN dealer. Driving with the doors locked
may make access to the pas-
senger compartment by the
emergency services more
diffi cult in an emergency.
As a safety measure (with children
on board), remove the key from the
ignition when leaving the vehicle,
even for a short time.
Do not make any modifi cations to the
electronic immobiliser system.
Do not discard the remote
control batteries, they con-
tain metals which are harm-
ful to the environment.
Take them to a CITROËN dealership,
or to any other approved collection
point. The high frequency remote control is
a sensitive system; do not operate it
in your pockets as there is a risk that
it may unlock the vehicle without you
being aware of this.
Avoid pressing the buttons of your
remote control out of range of your
vehicle, you risk rendering it inopera-
tive. It would then have to be repro-
grammed.

4
47
ACCESS
IMMOBILISER This locks the engine control sys-
tem as soon as the ignition has been
switched off and therefore prevents
starting of the vehicle by anyone who
does not have the key.
The ignition key has an electronic
chip which has a special code. When
the ignition is switched on, the code
must be recognised for starting to be
possible.
In the event of a malfunction, your
vehicle will not start.
Consult a CITROËN dealer.
Changing the remote control
battery
To change the battery, remove the
screw then unclip the housing using
a coin inserted at the ring.
Battery CR 2016/3 volts.
If the remote control does not work
after the battery has been changed,
reprogramme it. Reprogramming the remote
control
Following replacement of the remote
control battery or in the event of a re-
mote control malfunction, it may be
necessary to reprogramme the sys-
tem.

 Switch off the ignition.

 Switch the ignition on again.

 Press one of the remote control
buttons immediately for a few se-
conds.

 Switch off the ignition and remove
the key from the ignition lock.
The remote control is now working
again.
If the malfunction persists, contact a
CITROËN dealer. Driving with the doors locked
may make access to the pas-
senger compartment by the
emergency services more
diffi cult in an emergency.
As a safety measure (with children
on board), remove the key from the
ignition when leaving the vehicle,
even for a short time.
Do not make any modifi cations to the
electronic immobiliser system.
Do not discard the remote
control batteries, they con-
tain metals which are harm-
ful to the environment.
Take them to a CITROËN dealership,
or to any other approved collection
point. The high frequency remote control is
a sensitive system; do not operate it
in your pockets as there is a risk that
it may unlock the vehicle without you
being aware of this.
Avoid pressing the buttons of your
remote control out of range of your
vehicle, you risk rendering it inopera-
tive. It would then have to be repro-
grammed.

9
74
PRACTICAL INFORMATION
DIRECTION INDICATOR SIDE REPEATERS (WY 5 W AMBER)

 Push the repeater forwards or
rearwards and detach it by pull-
ing towards you.

 Disconnect the bulb holder and
change it.
CHANGING A FUSE
The fuse boxes are located under the
instrument panel trim and next to the
battery in the engine compartment.

Correct
Removing and fitting a fuse
Before changing a fuse, the cause of
the incident must be found and recti-
fi ed.

 Use the pliers A located in the
fuse box under the bonnet.

Incorrect

Pliers A Instrument panel fuse boxes
These are located on each side of
the instrument panel under the trim.

 Turn the steering wheel to the
left, remove bolt B .

 Turn the steering wheel to the
right (do not forget to release the
steering wheel using the key), re-
move bolt C .
Always replace a faulty fuse
with a fuse of the same rat-
ing (same colour).

9
74
PRACTICAL INFORMATION
DIRECTION INDICATOR SIDE REPEATERS (WY 5 W AMBER)

 Push the repeater forwards or
rearwards and detach it by pull-
ing towards you.

 Disconnect the bulb holder and
change it.
CHANGING A FUSE
The fuse boxes are located under the
instrument panel trim and next to the
battery in the engine compartment.

Correct
Removing and fitting a fuse
Before changing a fuse, the cause of
the incident must be found and recti-
fi ed.

 Use the pliers A located in the
fuse box under the bonnet.

Incorrect

Pliers A Instrument panel fuse boxes
These are located on each side of
the instrument panel under the trim.

 Turn the steering wheel to the
left, remove bolt B .

 Turn the steering wheel to the
right (do not forget to release the
steering wheel using the key), re-
move bolt C .
Always replace a faulty fuse
with a fuse of the same rat-
ing (same colour).

9
74
PRACTICAL INFORMATION
DIRECTION INDICATOR SIDE REPEATERS (WY 5 W AMBER)

 Push the repeater forwards or
rearwards and detach it by pull-
ing towards you.

 Disconnect the bulb holder and
change it.
CHANGING A FUSE
The fuse boxes are located under the
instrument panel trim and next to the
battery in the engine compartment.

Correct
Removing and fitting a fuse
Before changing a fuse, the cause of
the incident must be found and recti-
fi ed.

 Use the pliers A located in the
fuse box under the bonnet.

Incorrect

Pliers A Instrument panel fuse boxes
These are located on each side of
the instrument panel under the trim.

 Turn the steering wheel to the
left, remove bolt B .

 Turn the steering wheel to the
right (do not forget to release the
steering wheel using the key), re-
move bolt C .
Always replace a faulty fuse
with a fuse of the same rat-
ing (same colour).