2008 Citroen C CROSSER stop start

13
FAMILIARISATION
SITTING COMFORTABLY
Ignition switch

1. LOCK position.

2. ACC position.

3. ON position.

4. START position.

 74 Electric window controls

1. Driver’s electric window control.

2. Passenger’s electric window control.

3. Rear left electric window control.

4. Rear right electric window control.
Also...

5. Deactivation of the front passenger
and rear electric window controls.

 76 Sunroof controls

1. Opening control.

2. Closing control.

3. Partial opening control.
Also...

3. Also permits temporary stopping of
sunroof opening / closing.

 81

I N S T R U M E N T S a n d C O N T R O L S
I
22

Warning lights is on Cause Solution - action
Driver’s
seat belt not fastened Fixed The driver has not
fastened or has
unfastened his seat belt. This is accompanied by a message on the
instrument panel display.
Fasten the driver’s seat belt.
ABS
Fixed This comes on if an
anti-lock braking system
failure occurs. It is accompanied by a message on the
instrument panel display. The vehicle retains
conventional braking without assistance but
you are advised to stop. Have it checked by a
CITROËN dealer.
Air bags and
pretensioners Fixed This comes on for a
few seconds when the
ignition is turned to “ON”
then switches off.
It should switch off when the engine is started. If
it does not switch off, contact a CITROËN dealer.
This comes on if an air
bag or pretensioner
failure occurs. It is accompanied by a message on the
instrument panel display. Have the system
checked by a CITROËN dealer without delay.

A C C E S S
III
75
Do not throw the remote control batteries away, they contain metals which are harmful to the environment.
Take them to an approved collection point. Keys
Make a careful note of the number of each key. This number is
coded on the label attached to the key.
If the keys are lost, a CITROËN dealer can supply you wit h new keys.
Remote control
The high frequency remote control is a sensitive system; do not o perate it while it is in your pocket as there is a possibility
that it may unlock the vehicle, without you being aware of it.
Do not repeatedly press the buttons of your remote control out of range and out of sight of your vehicle.
You run the risk of stopping it from working. The remote contro l does not operate when the key is in the ignition, even when
the ignition is switched off.
Locking the vehicle
Driving with the doors locked may make access to the passenger compart ment by the emergency services more diffi cult
in an emergency.
As a safety precaution (with children on board), remove the key fro m the ignition when you leave the vehicle, even for a
short time.
Anti-theft protection
Do not make any modifi cations to the electronic engine immobi liser system, this could cause malfunctions.
When purchasing a second-hand vehicle
Have the key codes memorised by a CITROËN dealer, to ensure that the keys in your possession are the only ones which
can start the vehicle.

D R I V I N G
VII
110
Gear lever positions

N : neutral.
With your foot on the brake, select this
position to start.

R : reverse gear.
With the vehicle stationary, keep your
foot on the brake pedal and push the
gear lever upwards.

D : automated mode.
Move the lever downwards to select
this mode.
+/-: sequential mode with manual gear
changing. Functions of the steering wheel
controls

+ : manual gear changing in sequential
mode.
Press behind the “+” steering wheel
control to change up.

- : manual gear changing in sequential
mode.
Press behind the “-” steering wheel
control to change down. Stopping - Starting on a slope

Do not use the accelerator pedal to
immobilise the vehicle on a slope,
apply the handbrake instead.
When starting on a slope, accelerate
gradually while releasing the handbrake.
Switching to sequential mode
Once you have moved off, you can
switch to sequential mode by selecting
position +/-.

“D” disappears and the gears engaged
appear in succession on the instrument
panel display.
The gear change requests are only car-
ried out if the engine speed permits it.
- a
“-” steering wheel control 2 for se-
quential downward gear changes,
- a “+” steering wheel control 3 for
sequential upward gear changes.
Press the brake pedal fi rmly
while starting the engine.
Start the engine. “N” appears on the
instrument panel display.
Select fi rst gear (position D or +/-) or
reverse (position R ).
Release the handbrake.
Release the brake pedal then accelerate.

“D” or
“1” or
“R” appear on the
instrument panel display.
Move the lever downwards, then to the
left to select this mode, then:
- push forward to change up,
- push rearward to change down.
Moving off
Select position
N .

GH
G1G2G3
G4G5
H1H2
H3H4
A U D I O E Q U I P M E N T a n d T E L E M A T I C S
XI
176
Navigation settings and
information G
- Select the settings of functions
linked with the navigation to:
G1 - set the screen display parameters
such as:
- display 1 or 2 maps,
- display or do not display the POIs on the map, display selected
icons,
- change the colours of the map,
- display or do not display the name of the current street,
- display or do not display the address of the current street.
G2 - set route conditions,
G3 - set the route guidance mode and
the displaying of the results of the
route search.
G4 - save, change or delete a location
in the address book,

G5 - display and select the traffi c
information such as traffi c jams or
road works.
H - Select basic information relating to
the navigation as well as a pre-set
route demonstration to:
H1 - choose to divert your route to avoid
certain areas,
H2 - select a location using an advanced
search based on a POI along a
motorway or in the vicinity of the
motorway exit,
H3 - start/stop the demonstration,
H4 - recall a stored map screen.

A U D I O E Q U I P M E N T a n d T E L E M A T I C S
XI
187
Recording a CD onto the music server (1/3)
Press Explanations Result
All of the tracks are recorded automatically when a CD is inserte d.
This automatic recording is programmed by default on leaving th e
factory.
Automatic recording of all of the tracks
If you have changed the recording mode (manual or fi rst track), wh
ile a
CD is being played press [^] to access to secondary menu.
Press [REC. Setting].
Press [Auto REC.] and confi rm by pressing [Back].
Next, eject the CD currently being played then insert a CD and the
recording of all of the tracks begins.
If you wish to record the CD which is currently being played, press [^] to
access the secondary menu and press [REC. Start].
If another track (already recorded) is selected during recording, th e
recording continues and the new track selected is played.
If another track (not recorded) is selected, the recording which i s in
progress stops and the recording of the new track selected begins. This
track is played during recording.

A U D I O E Q U I P M E N T a n d T E L E M A T I C S
XI
188
Recording a CD onto the music server (2/3) Press Explanations Result
Manual recording of individual tracks
You can record the tracks manually, one by one.
After inserting a CD and while it is being played, press [^ ] to access the
secondary menu.
Press [REC. Setting].
Press [Manual REC.] and confi rm by pressing [Back].
Once the manual programming has been carried out, select the t rack to
be recorded then press [^].
Press [REC. Start], the recording of the track selected begins.
If another track is selected during recording, the recording stop s and the new
track selected is played.

A U D I O E Q U I P M E N T a n d T E L E M A T I C S
XI
189
Recording a CD onto the music server (3/3) Press Explanations Result
Automatic recording of the fi rst track
You can programme the automatic recording of the fi rst track when a CD
is inserted.
After inserting a CD and while it is being played, press [^ ] to access the
secondary menu.
Press [REC. Setting] then [Single REC.] and confi rm by pressing [ Back].
Next, eject the CD which is currently being played then inse rt a CD and
the recording of the fi rst track begins.
If you wish to record the fi rst track of the CD which is currentl y being
played, press[^] to access the secondary menu and press [REC. Start].
If another track is selected during recording, the recording stop s and the
track selected is played.
Stopping automatic or manual recording
During the recording of a CD or of a track on a CD, press [^] to access the
secondary menu.
Press [REC. Stop], the recording stops.