2008 CHRYSLER PT CRUISER tow

Side Window Demisters
A side window demister outlet is at each end of the
instrument panel. These nonadjustable outlets direct air
toward the side windows when the system is in either the
FLOOR, MIX, or DEFROST mode. The air is directed at
the area of the windows through which you view the
outside mirrors.
UNDERSTANDING YOUR INSTRUMENT PANEL 285
4

NReplacement Tires.....................328
NAlignment And Balance.................329
mTire Chains...........................330
mSnow Tires...........................330
mTire Rotation Recommendations............331
mTire Pressure Monitor System (TPMS) Ð
If Equipped...........................332
NBase System Ð If Equipped..............334
NGeneral Information...................336
mFuel Requirements Ð Gasoline Engines.......337
N2.4L And 2.4L Standard Turbo Engines......337
NReformulated Gasoline.................337
NGasoline/Oxygenate Blends..............337NMMT In Gasoline.....................338
NMaterials Added To Fuel................338
NFuel System Cautions..................338
NCarbon Monoxide Warnings..............339
mAdding Fuel..........................340
NFuel Filler Cap (Gas Cap)...............340
NLoose Fuel Filler Cap Message............342
mVehicle Loading........................342
mTrailer Towing.........................343
NCommon Towing Definitions.............343
NTrailer Hitch Classification...............345
NTrailer Towing Weights (Maximum Trailer
Weight Ratings)......................347
STARTING AND OPERATING 289
5

NTrailer And Tongue Weight..............348
NTowing Requirements..................349
NTowing Tips.........................354mRecreational Towing (Behind Motorhome, Etc.) . . 356
NTowing This Vehicle Behind Another Vehicle
(Flat Towing With All Four Wheels On The
Ground)............................356
290 STARTING AND OPERATING

MANUAL TRANSAXLE
Before starting the engine fully apply the parking brake,
press the clutch pedal to the floor and shift the gear
selector lever in NEUTRAL.
NOTE:The engine will not start unless the clutch pedal
is pressed to the floor.
NORMAL STARTING
Normal starting of either a cold or a warm engine does
not require pumping or depressing the accelerator pedal.
Simply turn the ignition switch to the START position
and release when the engine starts. If the engine has not
started within three seconds, slightly depress the accel-
erator pedal while continuing to crank. If the engine fails
to start within 15 seconds, turn the ignition switch to the
OFF position, wait 10 to 15 seconds, then repeat the
ªNORMAL STARTINGº procedure above.
WARNING!
Do not attempt to push or tow your vehicle to get it
started. Vehicles equipped with an automatic trans-
axle cannot be started this way. Unburned fuel could
enter the catalytic converter and once the engine has
started, ignite and damage the converter and vehicle.
If the vehicle has a discharged battery, booster cables
may be used to obtain a start from another vehicle.
This type of start can be dangerous if done improp-
erly, so follow the procedure carefully. See Section 6
of this manual for jump starting instructions.
EXTREMELY COLD WEATHER (BELOW220ÉF or
229ÉC)
To insure reliable starting at these temperatures, use of an
externally powered electric engine block heater (available
from your authorized dealer) is recommended.
292 STARTING AND OPERATING

The following chart should be used as a guide in deter-
mining the amount of engine idle time required to
sufficiently cool down the turbocharger before shut
down, depending upon the type of driving and the
amount of cargo.
TURBOCHARGER(COOL-DOWN(CHART
Driving Conditions IdleBefore Shut Down
Normal 0 min
Aggressive/Heavy Load 3 min
Trailer Tow 5 min
AUTOMATIC TRANSAXLE Ð IF EQUIPPED
You must step on the brake pedal and depress the gear
selector lever knob button before you will be able to shift
out of PARK.
CAUTION!
Damage to the transaxle may occur if the following
precautions are not observed:
²Shift into PARK only after the vehicle has come to a
complete stop.
²Shift into or out of REVERSE only after the vehicle has
come to a complete stop and the engine is at idle
speed.
²Do not shift from REVERSE, PARK, or NEUTRAL into
any forward gear when the engine is above idle speed.
²Before shifting into any gear, make sure your foot is
firmly on the brake pedal.
NOTE:You must step on the brake pedal and depress
the gear selector lever knob button before you will be
able to shift the gear selector lever out of PARK.
294 STARTING AND OPERATING

When frequent transaxle shifting occurs while using the
DRIVE/OVERDRIVE range, such as when operating the
vehicle under heavy loading conditions (in hilly terrain,
traveling into strong head winds, or while towing trail-
ers), use the[3]range.
[3] DRIVE
This range eliminates shifts into OVERDRIVE. The trans-
axle will operate normally in first and second while in
this range.
NOTE:Using the[3]range while operating the vehicle
under heavy operating conditions will improve perfor-
mance, fuel economy, and extend transaxle life by reduc-
ing excessive shifting and heat build up.
Use the[3]range when descending steep grades to
prevent brake system distress.
[1] Low
This range should be used for maximum engine braking
when descending steep grades. In this range, up shifts
will occur only to prevent engine over speed while down
shifts from[2]to[1]will occur as early as possible.
AUTOSTICK Ð IF EQUIPPED
AUTOSTICK is a driver-interactive transmission that
offers manual gear shifting capability to provide you
with more control. AUTOSTICK allows you to maximize
engine braking, eliminate undesirable upshifts and
downshifts, and improve overall vehicle performance.
This system can also provide you with more control
during passing, city driving, cold slippery conditions,
mountain driving, trailer towing, and many other situa-
tions.
STARTING AND OPERATING 299
5

To maintain a safe speed and prolong brake life, shift
down to SECOND or FIRST gear when descending a
steep grade.
When turning a corner, or driving up a steep grade,
downshift early so that the engine will not be overbur-
dened.
PARKING BRAKE
When the parking brake is applied with the
ignition on, the BRAKE Light in the instrument
cluster will come on.
NOTE:This light only shows that the parking brake is
on. It does not show the degree of brake application.If the parking brake is applied while the vehicle is
moving, a chime will sound to alert the driver. The chime
will sound up to 10 times or until the vehicle has
returned to a stop.
Before leaving the vehicle, make sure that the parking
brake is set. To set the parking brake, pull up firmly on
the lever. Always shift the gear selector lever into the
PARK position (automatic transaxle) or into the RE-
VERSE position (manual transaxle). To release the park-
ing brake, apply the brake pedal, pull up slightly on the
lever, then depress the button on the end of the lever and
push the lever fully down toward the floor.
STARTING AND OPERATING 305
5

NOTE:The parking brake lever will not release unless
the lever is pulled up slightly past its applied position.
When parking on a hill, it is important to set the parking
brake before placing the gear selector lever in PARK,
otherwise the load on the automatic transaxle locking
mechanism may make it difficult to move the gearselector lever out of PARK. As an added precaution, turn
the front wheels toward the curb on a downhill grade
and away from the curb on a uphill grade.
You should always apply the parking brake before leav-
ing the vehicle.
WARNING!
²Never leave children alone in a vehicle. Leaving
children in a vehicle unattended is dangerous for a
number of reasons. A child or others could be
seriously or fatally injured. Don't leave the keys in
the ignition. A child could operate power win-
dows, other controls, or move the vehicle.
²Be sure the parking brake is fully disengaged
before driving; failure to do so can lead to brake
failure and an accident.Parking Brake Lever
306 STARTING AND OPERATING