2008 CHEVROLET COBALT change wheel

{CAUTION:
Rust or dirt on a wheel, or on the parts to
which it is fastened, can make wheel nuts
become loose after time. The wheel could
come off and cause an accident. When you
change a wheel, remove any rust or dirt from
places where the wheel attaches to the vehicle.
In an emergency, you can use a cloth or a
paper towel to do this; but be sure to use a
scraper or wire brush later, if needed, to get
all the rust or dirt off. SeeChanging a Flat Tire
on page 5-74.
10. Place the compact spare tire on the wheel-mounting
surface.
{CAUTION:
Never use oil or grease on studs or nuts.
Because the nuts might come loose. The
vehicle’s wheel could fall off, causing a crash.11. Remove any rust or dirt
from the wheel bolts,
mounting surfaces,
and spare wheel.
Reinstall the wheel nuts with the rounded end
of the nuts toward the wheel. Tighten each nut by
hand until the wheel is held against the hub.
12. Lower the vehicle by turning the jack handle
counterclockwise. Lower the jack completely.
5-83

To change the front at tire:
Front Flat Tire Changing Procedure:
1. Perform a rear tire change by removing the rear tire
and installing the compact spare tire in the rear
wheel location. The rear road tire will be used
to replace the front at tire. See Rear Tire Changing
Procedure in this section.
2. Do a safety check before proceeding. SeeChanging
a Flat Tire on page 5-74.
3. If your vehicle has plastic wheel covers, use the
wheel wrench to loosen the plastic wheel nut caps.
Once the plastic wheel nut caps have been
loosened with the wheel wrench, you can nish
loosening them with your ngers. The plastic
nut caps do not come off.
4. Using the at end of the wheel wrench, pry along
the edge of the wheel cover until it comes off.
Store the wheel cover in the trunk until the at tire
is repaired or replaced.
5. Use the wheel wrench to loosen all the wheel nuts
on the at tire. Do not remove them yet.
5-85

10. Remove all of the
wheel nuts.
11. Remove any rust or dirt
from the wheel bolts,
mounting surfaces,
and spare wheel.
{CAUTION:
Rust or dirt on a wheel, or on the parts to which
it is fastened, can make wheel nuts become
loose after time. The wheel could come off and
cause an accident. When you change a wheel,
remove any rust or dirt from places where the
wheel attaches to the vehicle. In an emergency,
you can use a cloth or a paper towel to do this;
but be sure to use a scraper or wire brush later,
if needed, to get all the rust or dirt off. See
Changing a Flat Tire on page 5-74.
12. Place the tire on the wheel-mounting surface.
{CAUTION:
Never use oil or grease on studs or nuts.
Because the nuts might come loose. The
vehicle’s wheel could fall off, causing a crash.
5-87

9. Remove all of
the wheel nuts
and at tire.
{CAUTION:
Rust or dirt on a wheel, or on the parts to which
it is fastened, can make wheel nuts become
loose after time. The wheel could come off and
cause an accident. When you change a wheel,
remove any rust or dirt from places where the
wheel attaches to the vehicle. In an emergency,
you can use a cloth or a paper towel to do
this; but be sure to use a scraper or wire brush
later, if needed, to get all the rust or dirt off.
SeeChanging a Flat Tire on page 5-74.10. Remove any rust or dirt
from the wheel bolts,
mounting surfaces,
and spare wheel.
11. Place the compact spare tire on the wheel-mounting
surface.
{CAUTION:
Never use oil or grease on studs or nuts.
Because the nuts might come loose. The
vehicle’s wheel could fall off, causing a crash.
12. Reinstall the wheel nuts with the rounded end of
the nuts toward the wheel. Tighten each nut by
hand until the wheel is held against the hub.
13. Lower the vehicle by turning the jack handle
counterclockwise. Lower the jack completely.
5-91