2008 CADILLAC ESCALADE ESV audio

EXIT FEATURE SETTINGS This feature allows you to exit the feature settings menu.
Press the customization button until PRESS
V TO EXIT
FEATURE SETTINGS appears in the DIC display.
Press the set/reset button once to exit the menu.
If you do not exit, pressing the customization button
again will return you to the beginning of the feature
settings menu.
Exiting the Feature Settings Menu The feature settings menu will be exited when any of
the following occurs:
The vehicle is no longer in ON/RUN.
The trip/fuel or vehicle information DIC buttons are
pressed.
The end of the feature settings menu is reached
and exited.
A 40 second time period has elapsed with no
selection made. Audio System(s) Determine which radio your vehicle has and then read
the pages following to familiarize yourself with its
features.
{ CAUTION: This system provides you with far greater
access to audio stations and song listings.
Giving extended attention to entertainment
tasks while driving can cause a crash and you
or others can be injured or killed. Always keep
your eyes on the road and your mind on the
drive — avoid engaging in extended searching
while driving.
Keeping your mind on the drive is important for safe
driving. See Defensive Driving on page 4-2 . Here
are some ways in which you can help avoid distraction
while driving.
3-70

While your vehicle is parked:
Familiarize yourself with all of its controls.
Familiarize yourself with its operation.
Set up your audio system by presetting your
favorite radio stations, setting the tone, and
adjusting the speakers. Then, when driving
conditions permit, you can tune to your favorite
radio stations using the presets and steering wheel
controls if the vehicle has them.
Notice: Before adding any sound equipment to
your vehicle, such as an audio system, CD player,
CB radio, mobile telephone, or two-way radio, make
sure that it can be added by checking with your
dealer/retailer. Also, check federal rules covering
mobile radio and telephone units. If sound
equipment can be added, it is very important to do
it properly. Added sound equipment may interfere
with the operation of your vehicle’s engine, radio, or
other systems, and even damage them. Your
vehicle’s systems may interfere with the operation
of sound equipment that has been added.
Notice: The chime signals related to safety belts,
parking brake, and other functions of your vehicle
operate through the radio/entertainment system.
If that equipment is replaced or additional equipment
is added to your vehicle, the chimes may not work. Make sure that replacement or additional
equipment is compatible with your vehicle before
installing it. See Accessories and Modifications
on page 5-3 .
Your vehicle may have a feature called Retained
Accessory Power (RAP). With RAP, the audio system
can be played even after the ignition is turned off.
See Retained Accessory Power (RAP) on page 2-26 for
more information.
Setting the Clock 1. Press the
w (tune/select) knob (the passenger
side knob) to enter the main menu.
2. Turn the same knob until SET CLOCK displays.
3. Press this knob to select SET CLOCK.
4. Turn this knob to adjust the time.
5. Press the same knob to update the time. VEHICLE
TIME UPDATED displays.
If the CLOCK/RADIO DISP (display) is programmed into
one of the congurable keys, pressing the key switches
the display back to the clock set function. The time
and date always appears on the radio display.
See “Congurable Radio Display Keys” later in this
section for more information on conguring the keys.
3-71

Setting the Date 1. Press the
w knob (the passenger side knob) to
enter the main menu.
2. Turn the same knob until SET DATE displays.
3. Press this knob to select SET DATE.
4. Turn this knob to adjust the date.
5. Press the same knob to update the time. VEHICLE
DATE UPDATED displays.
If the DATE is programmed into one of the congurable
keys, pressing the key switches the display back to
the date set function. The time and date always appears
on the radio display. See “Congurable Radio Display
Keys” later in this section for more information on
conguring the keys. Radio(s)
Playing the Radio
O (Power): Press to turn the radio on and off.
Press and hold for more than two seconds to turn off
the radio, RSE (Rear Seat Entertainment) video screen,
and RSA (Rear Seat Audio).
n (Volume): Turn clockwise or counterclockwise to
increase or to decrease the volume. Radio with CD and DVD
3-72

SRCE (Source): Press to select a source, either radio,
CD, DVD, or auxiliary, if your vehicle has this feature.
The CD or DVD must be loaded to select the source and
to play. CD or DVD displays if a disc is loaded. If a
CD or DVD is not loaded, the display changes to the
auxiliary source, if your vehicle has this feature, or
continues to play the radio.
Vehicle Noise Compensation (VNC): Your vehicle has
a Bose ®
audio system. It includes Bose AudioPilot ®
noise
compensation technology. When turned on, AudioPilot ®
continuously adjusts the audio system equalization, to
compensate for background noise, so that the audio
always sounds the same at the set volume level.
This feature is most effective at lower radio volume
settings where background noise can affect how well the
music is being heard through the audio system. At
higher volume settings, where the music is much louder
than the background noise, there might be little or no
adjustments by AudioPilot ®
.
Turn the AudioPilot ®
on by pressing the
w(tune/select) knob to enter the main menu. Then turn
this knob until VNC:AUDIOPILOT displays. Press
this knob to turn AudioPilot ®
on and off. An X appears
in the box while it is on. To turn AudioPilot ®
off, press the
w knob to enter
the main menu, turn this knob until VNC:AUDIOPILOT
appears, and press this knob. The X in the box
disappears when it is turned off. For additional
information on AudioPilot ®
, visit
www.bose.com/audiopilot.
Finding a Station BAND: Press to select AM, FM1, FM2, or XM1 or XM2
(if equipped).
w (Tune/Select): Turn to select radio stations.
©¨ (Seek): Press the left arrow to go to the previous
station and stay there. Press the right arrow to go to
the next station and stay there. The sound mutes while
seeking.
The radio only seeks stations with a strong signal that
are in the selected band.
3-73

Setting the Tone
(Bass/Midrange/Treble) To adjust the bass, midrange, and treble, perform the
following steps:
1. Press the
w knob to enter the main menu.
2. Turn this knob until BASS – MID – TREBLE
displays.
3. Press this knob to scroll through the settings.
4. Turn this knob again to increase or to decrease the
bass, midrange, or treble. If a station is weak or
has static, decrease the treble.
5. Press this knob to set the adjustment.
6. Press the BACK (F6) button to exit the display. To
return to the original display, repeatedly press the
BACK (F6) button or wait for the display to time out.
AUDIO EQUALIZER: This feature lets you select
customized equalization settings. To choose an
equalization setting (EQ0 through EQ5), perform the
following steps:
1. Press the
w knob to enter the main menu.
2. Turn this knob until EQUALIZER displays. 3. Press this knob again to set the equalization
setting. The equalization setting displays.
4. Press the BACK (F6) button to exit the display. To
return to the original display, repeatedly press the
BACK (F6) button or wait for the display to time out.
The equalization settings are preset to EQ0 (Normal),
EQ1 (Pop), EQ2 (Rock), EQ3 (Jazz), EQ4 (Talk),
and EQ5 (Country).
Adjusting the Speakers (Balance/Fade) To adjust the balance or fade, perform the
following steps:
1. Press the
w knob to enter the main menu.
2. Turn this knob until BALANCE – FADER displays.
3. Press this knob to enter the tone settings.
4. Press this knob again to scroll to BALANCE or
FADER.
5. Turn this knob to adjust the BALANCE to the right
or the left speakers and the FADER to the front or
the rear speakers.
6. Press this knob again to set the adjustment.
7. Press the BACK (F6) button to exit the display. To
return to the original display, repeatedly press the
BACK (F6) button or wait for the display to time out.
EQ0 does not display while in this mode.
3-76

Digital Signal Processing (DSP): This feature is used
to provide a choice of different listening experiences.
To choose a DSP setting, perform the following steps:
1. Press the
w knob to enter the main menu.
2. Turn this knob until DSP displays.
3. Press this knob again to set the DSP setting. The
DSP setting displays.
4. Press the BACK (F6) button to exit the display. To
return to the original display, repeatedly press the
BACK (F6) button or wait for the display to time out.
The DSP settings available are:
Normal : Select this setting for normal mode. It
provides the best sound quality for all seating
positions.
Centerpoint ®
: Select this setting to enable Bose
Centerpoint ®
. Centerpoint ®
signal processing
gives surround sound quality for a CD, MP3, or a
DVD stereo audio source. Centerpoint ®
delivers ve
independent audio channels from conventional
stereo recordings. Rear : Select this setting to adjust the audio for the
rear seat passengers to receive the best possible
sound quality.
Driver : Select this setting to adjust the audio for the
driver to receive the best possible sound quality.
5.1 Surround : Select this setting to turn on true 5.1
surround sound processing, available for DVD-A or
DVD-V sources that were recorded in 5.1
Surround. This setting is only available if the Rear
Seat Audio (RSA) control is turned off.
5.1 Surround + Normal — Select this mode
for the best audio, for all seating positions.
5.1 Surround + Rear — Select this mode for
the best audio, for rear seat occupants.
3-77

XM™ Satellite Radio Service XM™ is a satellite radio service that is based in the
48 contiguous United States and 10 Canadian provinces.
XM™ Satellite Radio has a wide variety of programming
and commercial-free music, coast-to-coast, and in
digital-quality sound. During your trial or when you
subscribe, you will get unlimited access to XM™ Radio
Online for when you are not in your vehicle. A service fee
is required to receive the XM™ service. For more
information, contact XM™ at www.xmradio.com or call
1-800-929-2100 in the U.S. and www.xmradio.ca or call
1-877-438-9677 in Canada.
4 (Information): Press while in XM™ mode to retrieve
additional text information related to the current
XM™ station such as: Channel, Song, Artist, and CAT
(category). To view this information, perform the
following:
1. Press the
w knob to enter the main menu.
2. Turn this knob until INFO (information) displays.
3. Press this knob again to select INFO. The display
changes to show the additional XM™ information.
4. Press the BACK (F6) button to exit the display. To
return to the original display, repeatedly press the
BACK (F6) button or wait for the display to time out. Radio Data System (RDS) The audio system has a Radio Data System (RDS).
RDS features are available for use only on FM stations
that broadcast RDS information.
With RDS, the radio can do the following:
Seek to stations broadcasting the selected type of
programming.
Receive announcements concerning local and
national emergencies.
Display messages from radio stations.
Seek to stations with traffic announcements.
This system relies upon receiving specic information
from these stations and only works when the information
is available. In rare cases, a radio station could
broadcast incorrect information that causes the radio
features to work improperly. If this happens, contact the
radio station.
While the radio is tuned to an RDS station, the station
name or call letters display instead of the frequency.
RDS stations can also provide the time of day, a
program type (PTY) for current programming, and the
name of the program being broadcast.
The RDS function does not work with XM™.
3-78

Playing an MP3 CD-R Disc Radios with the MP3 feature are capable of playing an
MP3 CD-R disc. For more information on how to
play an MP3 CD-R disc, see Using an MP3 on
page 3-90 later in this section.
CD Messages If the CD comes out, it could be for one of the following
reasons:
It is very hot. When the temperature returns to
normal, the CD should play.
You are driving on a very rough road. When the
road becomes smoother, the CD should play.
The CD is dirty, scratched, wet, or upside down.
The air is very humid. If so, wait about an hour and
try again.
The format of the CD might not be compatible. See
Using an MP3 on page 3-90 later in this section.
There could have been a problem while burning
the CD.
The label could be caught in the CD player.
If any error occurs repeatedly or if an error cannot be
corrected, contact your dealer/retailer. If the radio
displays an error message, write it down and provide it
to your dealer/retailer when reporting the problem. Using the DVD Player Insert a disc partway into the slot, label side up. The
player pulls it in. If the ignition and the radio are on, the
CD or DVD begins playing. A DVD can be loaded
with the radio off, but it does not start playing until the
radio is on, and sourced to DVD. The DVD player
can be controlled by the buttons on the radio, the RSA
(Rear Seat Audio) system, and the remote control, if
your vehicle has this feature. See the Rear Seat
Entertainment (RSE) System on page 3-95 for more
information. A DVD icon displays whenever a disc
is loaded. The DVD player can also be run for
passengers in the rear seat with the radio off. The rear
seat passenger can power on the video screen and
use the remote control to navigate the disc. See Rear
Seat Entertainment (RSE) System on page 3-95 for
more information.
The DVD player is capable of playing both DVD video
and DVD audio discs. This DVD player includes Dolby ®
Digital Decoding*, and DTS ®
Decoding**, so discs
can be played that were recorded using these
technologies.
*Manufactured under license from Dolby ®
Laboratories.
Dolby ®
, and the double-D symbol are registered
trademarks of Dolby ®
Laboratories.
**DTS and DTS Digital Surround are registered
trademarks of Digital Theater Systems Inc.
3-84