2008 CADILLAC ESCALADE ESV lock

Tire and Loading Information Label
A vehicle specic Tire and Loading Information
label is attached to the center pillar (B-pillar). With
the driver’s door open, you will nd the label
attached below the door lock post (striker). The tire
and loading information label shows the number of
occupant seating positions (A), and the maximum
vehicle capacity weight (B) in kilograms and
pounds.
The Tire and Loading Information label also shows
the size of the original equipment tires (C) and
the recommended cold tire ination pressures (D). For more information on tires and ination see
Tires on page 5-56 and Inflation - Tire Pressure on
page 5-62 .
There is also important loading information on the
vehicle Certication/Tire label. It tells you
the Gross Vehicle Weight Rating (GVWR) and the
Gross Axle Weight Rating (GAWR) for the front
and rear axles. See “Certication/Tire Label” later
in this section.
Steps for Determining Correct Load Limit 1.
Locate the statement “The combined weight of
occupants and cargo should never exceed
XXX kg or XXX lbs” on your vehicle’s placard. 2.
Determine the combined weight of the driver
and passengers that will be riding in your
vehicle. 3.
Subtract the combined weight of the driver
and passengers from XXX kg or XXX lbs.
4.
The resulting gure equals the available
amount of cargo and luggage load capacity.
For example, if the “XXX” amount equals
1400 lbs and there will be ve 150 lb
passengers in your vehicle, the amount of
available cargo and luggage load capacity is
650 lbs (1400 − 750 (5 x 150) = 650 lbs).Label Example
4-36

Automatic Level Control
The automatic level control rear suspension
comes as a part of the Road Sensing Suspension.
See Road Sensing Suspension on page 4-6 .
This type of level control is fully automatic and will
provide a better leveled riding position as well
as better handling under a variety of passenger
and loading conditions. An air compressor
connected to the rear shocks will raise or lower
the rear of the vehicle to maintain proper vehicle
height. The system is activated when the
ignition key is turned to RUN and will automatically
adjust vehicle height thereafter. The system
may exhaust (lower vehicle height) for up to
10 minutes after the ignition key has been turned
to LOCK. You may hear the air compressor
operating when the height is being adjusted. If a weight-distributing hitch is being used, it is
recommended to allow the shocks to inate,
thereby leveling the vehicle prior to adjusting the
height. See “Weight distributing Hitches and
Weight Carrying Hitches” under Towing a Trailer
on page 4-44 .
Towing Towing Your Vehicle Consult your dealer/retailer or a professional towing
service if you need to have your disabled vehicle towed.
See Roadside Service on page 7-6 .
If you want to tow your vehicle behind another vehicle
for recreational purposes (such as behind a motorhome),
see Recreational Vehicle Towing following.
4-41

If you’ll be pulling a trailer that, when loaded, will weigh
more than 5,000 lbs (2 270 kg) be sure to use a
properly mounted weight-distributing hitch and sway
control of the proper size. This equipment is very
important for proper vehicle loading and good handling
when driving. You should always use a sway control
if your trailer will weigh more than these limits. You can
ask a hitch dealer about sway controls.
Hitch Cover Your vehicle may have a hitch cover. To remove the
hitch cover:
1. Turn the fasteners on the lower tabs 90 degrees
counterclockwise.
2. Lift the lower edge of the cover about 45 degrees.
3. Pull the cover downward to disengage the upper
attachments. To reinstall the hitch cover:
1. Hold the cover at a 45 degree angle to the vehicle
and push the upper tabs in the hitch cover into the
chrome slots in the fascia.
2. Move the bottom of the cover forward until the
lower tabs line up with the lower fascia slots.
3. Snap the hitch cover into place by pushing the
upper corners forward.
4. Turn the fasteners on the lower tabs 90 degrees
clockwise to lock the cover in place.
4-51

Tire Pressure Monitor Operation .................... .5-65
Tire Inspection and Rotation .......................... .5-69
When It Is Time for New Tires ...................... .5-71
Buying New Tires ........................................ .5-72
Different Size Tires and Wheels ..................... .5-73
Uniform Tire Quality Grading ......................... .5-74
Wheel Alignment and Tire Balance ................. .5-75
Wheel Replacement ..................................... .5-76
Tire Chains ................................................. .5-77
If a Tire Goes Flat ....................................... .5-78
Changing a Flat Tire .................................... .5-79
Removing the Spare Tire and Tools ............... .5-80
Removing the Flat Tire and Installing the
Spare Tire ............................................... .5-85
Secondary Latch System .............................. .5-90
Storing a Flat or Spare Tire and Tools ........... .5-94
Spare Tire .................................................. .5-98
Appearance Care ........................................... .5-98
Interior Cleaning .......................................... .5-98
Fabric/Carpet ............................................. .5-100
Leather ..................................................... .5-100
Instrument Panel, Vinyl, and Other Plastic
Surfaces ................................................ .5-101
Wood Panels ............................................. .5-101
Speaker Covers ......................................... .5-101
Care of Safety Belts ................................... .5-101 Weatherstrips ............................................ .5-101
Washing Your Vehicle ................................. .5-102
Cleaning Exterior Lamps/Lenses ................... .5-102
Finish Care ............................................... .5-102
Windshield, Backglass, and Wiper Blades ...... .5-103
Aluminum or Chrome-Plated Wheels
and Trim ............................................... .5-104
Tires ........................................................ .5-105
Sheet Metal Damage .................................. .5-105
Finish Damage .......................................... .5-105
Underbody
Maintenance .............................. .5-105
Chemical Paint Spotting .............................. .5-105
Vehicle Care/Appearance Materials ............... .5-106
Vehicle Identication .................................... .5-107
Vehicle Identication Number (VIN) ............... .5-107
Service Parts Identication Label .................. .5-107
Electrical System ......................................... .5-108
Add-On Electrical Equipment ........................ .5-108
Windshield Wiper Fuses .............................. .5-108
Power Windows and Other Power Options ..... .5-108
Fuses and Circuit Breakers ......................... .5-108
Instrument Panel Fuse Block ....................... .5-109
Center Instrument Panel Fuse Block ............. .5-110
Underhood Fuse Block ............................... .5-111
Capacities and Specications ....................... .5-115Section 5 Service and Appearance Care
5-2

Service For service and parts needs, visit your dealer/retailer.
You will receive genuine GM parts and GM-trained and
supported service people.
Genuine GM parts have one of these marks:
Accessories and Modications When non-dealer/non-retailer accessories are added to
your vehicle they can affect your vehicle’s performance
and safety, including such things as, airbags, braking,
stability, ride and handling, emissions systems,
aerodynamics, durability, and electronic systems like
antilock brakes, traction control and stability control.
Some of these accessories could even cause
malfunction or damage not covered by warranty.
GM Accessories are designed to complement and
function with other systems on your vehicle. Your GM
dealer/retailer can accessorize your vehicle using
genuine GM Accessories. When you go to your GM
dealer/retailer and ask for GM Accessories, you will know
that GM-trained and supported service technicians will
perform the work using genuine GM Accessories.
Also, see Adding Equipment to Your Airbag-Equipped
Vehicle on page 1-90 .
California Proposition 65 Warning Most motor vehicles, including this one, contain and/or
emit chemicals known to the State of California to
cause cancer and birth defects or other reproductive
harm. Engine exhaust, many parts and systems
(including some inside the vehicle), many uids, and
some component wear by-products contain and/or emit
these chemicals.
5-3

To open the fuel door, push the rearward center edge
inboard and release. The door will pop open.
To remove the fuel cap, turn it slowly counterclockwise.
The fuel cap has a spring in it; if the cap is released
too soon, it will spring back to the right. While refueling, hang the tethered fuel cap from the
hook on the fuel door.
{ CAUTION: Fuel can spray out on you if you open the fuel
cap too quickly. If you spill fuel and then
something ignites it, you could be badly burned.
This spray can happen if your tank is nearly full,
and is more likely in hot weather. Open the fuel
cap slowly and wait for any hiss noise to stop.
Then unscrew the cap all the way.
Be careful not to spill fuel. Do not top off or overll
the tank and wait a few seconds after you have
nished pumping before removing the nozzle.
Clean fuel from painted surfaces as soon as possible.
See Washing Your Vehicle on page 5-102 .
5-8

When replacing the fuel cap, insert the tether in its hole
before tightening the cap. Turn the fuel cap clockwise
until it clicks. It will require more effort to turn the
fuel cap on the last turn as you tighten it. Make sure
the cap is fully installed. The diagnostic system
can determine if the fuel cap has been left off or
improperly installed. This would allow fuel to evaporate
into the atmosphere. See Malfunction Indicator Lamp
on page 3-43.
If your vehicle has a Driver Information Center (DIC),
the TIGHTEN GAS CAP message will be displayed
if the fuel cap is not properly installed.
{ CAUTION: If a re starts while you are refueling, do not
remove the nozzle. Shut off the ow of fuel by
shutting off the pump or by notifying the
station attendant. Leave the area immediately.
Notice: If you need a new fuel cap, be sure to get
the right type. Your dealer/retailer can get one
for you. If you get the wrong type, it may not t
properly. This may cause your malfunction indicator
lamp to light and may damage your fuel tank and
emissions system. See Malfunction Indicator Lamp
on page 3-43 .
5-9

A. Engine Air Cleaner/Filter. See Engine Air
Cleaner/Filter on page 5-17 .
B. Air Filter Restriction Indicator (If Equipped).
See Engine Air Cleaner/Filter on page 5-17 .
C. Coolant Surge Tank and Pressure Cap. See Cooling
System on page 5-29 and Coolant Surge Tank
Pressure Cap on page 5-26 .
D. Remote Positive (+) Terminal. See Jump Starting
on page 5-40 .
E. Battery. See Battery on page 5-39 .
F. Engine Oil Fill Cap. See “When to Add Engine Oil”
under Engine Oil on page 5-14 .
G. Automatic Transmission Dipstick (Out of View).
See “Checking the Fluid Level” under Automatic
Transmission Fluid on page 5-20 . H. Remote Negative ( − ) Terminal (GND) (Out of View).
See Jump Starting on page 5-40 .
I. Engine Oil Dipstick (Out of View). See “Checking
Engine Oil” under Engine Oil on page 5-14 .
J. Engine Cooling Fan (Out of View). See Cooling
System on page 5-29 .
K. Power Steering Fluid Reservoir (Out of View).
See Power Steering Fluid on page 5-34 .
L. Brake Master Cylinder Reservoir. See “Brake Fluid”
under Brakes on page 5-36 .
M. Underhood Fuse Block. See Underhood Fuse Block
on page 5-111 .
N. Windshield Washer Fluid Reservoir. See “Adding
Washer Fluid” under Windshield Washer Fluid
on page 5-35 .
5-13