2008 CADILLAC CTS lock

To remove the key, press
the button (A) near the
bottom of the keyless
access transmitter, and
pull the key out. Never
pull the key out without
pressing the button.
This vehicle may have the Keyless Access System.
SeeIgnition Positions (Key Access) on page 2-32
orIgnition Positions (Keyless Access) on page 2-34
for information on starting the vehicle.
Notice:If you ever lock your keys in the vehicle,
you may have to damage the vehicle to get in.
Be sure you have spare keys.
In an emergency, contact Roadside Assistance.
SeeRoadside Service on page 7-7.Remote Keyless Entry (RKE)
System
If this vehicle has the Remote Keyless Entry (RKE)
system, it operates on a radio frequency subject
to Federal Communications Commission (FCC)
Rules and with Industry Canada.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation of the device.
This device complies with RSS-210 of Industry Canada.
Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation of the device.
Changes or modications to this system by other than
an authorized service facility could void authorization to
use this equipment.
2-6

If there is a decrease in the RKE operating range,
try this:
Check the distance. The transmitter may be too
far from the vehicle. Stand closer during rainy
or snowy weather.
Check the location. Other vehicles or objects may
be blocking the signal. Take a few steps to the
left or right, hold the transmitter higher, and
try again.
Check the transmitter’s battery. See “Battery
Replacement” later in this section.
If the transmitter is still not working correctly, see
your dealer/retailer or a qualied technician for
service.
Remote Keyless Entry (RKE)
System Operation
The Remote Keyless Entry (RKE) transmitter functions
work up to 65 feet (20 m) away.
There are other conditions which can affect the
performance of the transmitter. SeeRemote Keyless
Entry (RKE) System on page 2-6.
Q(Lock):Press to lock all the doors. If enabled
through the Driver Information Center (DIC), the parking
lamps may ash once to indicate locking has occurred,
or the horn may chirp when
Qis pressed again within
ve seconds from the previous press of the lock button.
SeeDIC Vehicle Customization on page 3-69for
additional information.
2-7

"(Unlock):Press to unlock the driver’s door. If"is
pressed again within ve seconds, all remaining doors
unlock. The interior lamps come on and stay on for
20 seconds or until the ignition is turned on. If enabled
through the DIC, the parking lamps ash twice to indicate
unlocking has occurred. SeeDIC Vehicle Customization
on page 3-69.
V(Remote Trunk Release):Press and hold
for about one second to release the trunk lid.
The transmission must be in PARK (P).
L(Vehicle Locator/Panic Alarm):Press and release
to locate the vehicle. The turn signal lamps ash and
the horn sounds three times.
Press and hold
Lfor more than two seconds to
activate the panic alarm. The turn signal lamps ash
and the horn sounds for 30 seconds. The alarm turns off
when the ignition is moved to START or
Lis pressed
again. The ignition must be in LOCK/OFF for the
panic alarm to work.
Matching Transmitter(s) to Your
Vehicle
Each RKE transmitter is coded to prevent another
transmitter from unlocking the vehicle. If a transmitter is
lost or stolen, a replacement can be purchased through
your dealer/retailer. All transmitters need to be re-coded
to match the new transmitter.
The lost transmitter no longer works after the new
transmitters are re-coded. The vehicle can have a
maximum of eight transmitters matched to it. See
“Relearn Remote Key” underDIC Operation and
Displays on page 3-48.
Battery Replacement
Replace the battery if the Replace Battery In Remote
Key message displays in the DIC. See “Replace Battery
In Remote Key” underDIC Warnings and Messages
on page 3-56for additional information.
Notice:When replacing the battery, do not touch
any of the circuitry on the transmitter. Static
from your body could damage the transmitter.
2-8

If you ever notice a decrease in the keyless access
transmitter range, try doing one of the following:
Check the distance. You may be too far from your
vehicle. You may need to stand closer during
rainy or snowy weather.
Check the location. Other vehicles or objects may
be blocking the signal. Take a few steps to the
left or right, hold the transmitter higher, and
try again.
Check to determine if battery replacement is
necessary. See “Battery Replacement” under
Keyless Access System Operation on page 2-10.
Check to make sure that an electronic device such
as a cellular phone or lap top computer is not
causing interference.
If you are still having trouble, see your dealer/retailer
or a qualied technician for service.
Keyless Access System Operation
The Keyless Access System transmitter functions
will work up to 195 feet (60 m) away, however, the
operating range may be less while the vehicle is running.
The Keyless Access System also lets you lock and
unlock the vehicle’s doors and access the trunk without
removing the remote transmitter from your pocket, purse,
briefcase, etc. The system operates when a front door
handle is pulled or the remote trunk release button is
pressed. You must have the keyless access transmitter
with you and within 3 feet (1 m) of the door or trunk you
are opening. See “Keyless Locking” and “Keyless Unlock”
underDIC Vehicle Customization on page 3-69.
There are other conditions which can affect the
performance of the transmitter. SeeKeyless Access
System on page 2-9.
2-10

Your vehicle comes with
two transmitters.
Q(Lock):Press to lock the doors. The turn signal
indicators will ash. If
Qis pressed twice, the doors
will lock, the turn signal indicators will ash twice,
and the horn will sound once.
You can program your vehicle so the turn signal
indicators will not ash and the horn will not sound
when pressing
Qon the keyless access transmitter.
For more information see″Remote Door Lock″under
DIC Vehicle Customization on page 3-69.
"(Unlock):Press once to unlock the driver’s door.
The turn signal indicators will ash twice.
Press
"twice within ve seconds to unlock all the
doors. If it is dark enough outside, your interior lamps
will come on.
You can program your vehicle so the turn signal
indicators will not ash and the fog lamps and reverse
lamps remain on steady for about 20 seconds when
the keyless access transmitter is used to unlock the
vehicle. See″Remote Door Unlock″underDIC Vehicle
Customization on page 3-69.
If your vehicle has the memory feature you can program
and recall memory settings when you press
"on the
keyless access transmitter. SeeMemory Seat, Mirrors
and Steering Wheel on page 1-7for more information.
/(Remote Start):If your vehicle has this feature,
press
/after pressingQto operate the remote start
feature. SeeRemote Vehicle Start on page 2-16
for additional information. With Remote Start
Shown, Without Similar
2-11

G(Trunk):Press and hold for about one second
to open the trunk while the engine is turned off or
the shift lever is in PARK (P).
L(Vehicle Locator/Panic Alarm):Press and release
to locate your vehicle. The horn will chirp three times
and the turn signal lamps will ash three times.
Press and hold
Lfor three seconds to sound the panic
alarm. The horn will chirp and the turn signal lamps
will ash for 30 seconds. Press and release
Lagain
to cancel the panic alarm.
Matching Transmitter(s) to Your
Vehicle
Each Keyless Access System is coded to allow only
transmitters programmed to your vehicle to work.
If a transmitter is lost or stolen, a replacement can be
purchased and programmed through your dealer/retailer.
Your dealer/retailer can reprogram your vehicle so
lost or stolen transmitters no longer work with your
vehicle. Each vehicle can have a maximum of four
transmitters matched to it.To match a new transmitter to your vehicle when
you have a recognized transmitter, do the following.
Two recognized transmitters are required for Canadian
owners.
1. The vehicle must be off.
2. Have the recognized transmitter and the new,
unrecognized transmitter(s) with you.
3. Insert the key into the key lock cylinder located on
the outside of the driver’s door.
4. Turn the key to the unlock position ve times within
ve seconds.
5. The Driver Information Center (DIC) will display
Ready To Learn Electronic Key #X, where X can
be2,3or4.
6. Place the new,
unrecognized
transmitter into the
transmitter pocket with
the transmitter buttons
facing the front of the
vehicle. The transmitter
pocket is inside the
center console storage
area located between
the driver and front
passenger seats.
2-12

7. Once the transmitter is programmed, a beep will
sound. The DIC will display Ready To Learn
Electronic Key #X, where X can be 3 or 4, or
Maximum # Electronic Keys Learned.
8. Press the ignition control knob to exit
programming mode.
9. Remove the transmitter from the transmitter pocket
and press the unlock button on the keyless access
transmitter two times.
The Canadian immobilizer standard requires Canadian
owners to see their dealer/retailer for matching new
transmitters when two recognized transmitters are not
available. United States owners are permitted to match
a new transmitter to their vehicle when a recognized
transmitter is not available.The procedure will require three, ten minute cycles to
complete the matching process.
1. The vehicle must be off.
2. Place the new,
unrecognized
transmitter into the
transmitter pocket with
the transmitter buttons
facing the front of the
vehicle. The transmitter
pocket is inside the
center console storage
area located between
the driver and front
passenger seats.
3. Insert the vehicle key into the key lock cylinder
located on the driver’s door.
2-13

4. Turn the key to the unlock position ve times within
ve seconds.
5. The DIC will display Press Start Control To
Learn Keys.
6. Press the ignition switch in.
7. The DIC will read Learn Delay Active Wait XX Min
and will count down to zero, one minute at a time.
8. The DIC will display Press Start Control To Learn
Keys again.
9. Press the ignition switch in again.
10. The DIC will again read Learn Delay Active Wait
XX Min and will count down to zero, one minute at
a time.
11. The DIC will display Press Start Control To Learn
Keys again.
12. Press the ignition switch in again.
13. The DIC will again read Learn Delay Active Wait
XX Min and will count down to zero, one minute at
a time.14. A beep will sound and the DIC will read Ready To
Learn Electronic Key # X. At this time, all previously
known transmitters have been erased.
15. Once the transmitter is recognized and
programmed, a beep will sound and the DIC will
display Ready To Learn Electronic Key # X.
16. To program additional transmitters, insert each
transmitter in the pocket until you hear a beep
and the DIC advances to the next electronic key
number.
17. When complete, press the ignition control knob.
18. Press the unlock button on each transmitter
programmed to complete programming.
Up to four transmitters can be programmed to the
vehicle. The DIC will display Maximum # Electronic Keys
Learned and will exit the programming mode.
After performing this process, transmitters previously
programmed will no longer work with your vehicle
and must be reprogrammed.
2-14