
Mobility
 219Reference
At a glance
Controls
Driving tips
Communications
Navigation
Entertainment
Convertible: tire inflation pressures for the 335i
Tire size Pressure specifications in psi/kPa 
Traveling speeds
up to a max. of
100 mph / 160 km/hTraveling speeds
including those exceeding
100mph / 160km/h
All pressure specifications in 
the table are indicated in 
psi/kilopascal with cold tires. 
Cold = ambient temperature
without Sports package:
225/45 R 17 91 H M+S 32/220 38/260 32/220 36/250 35/240 42/290
225/45 R 17 94 V M+S XL 32/220 39/270 32/220 36/250 36/250 44/300
Front: 225/45 R 17 91 V 32/220 - 32/220 - 32/220 -
Rear: 255/40 R 17 94 V - 33/230 - 33/230 - 39/270
Front: 225/40 R 18 88 W 32/220 - 32/220 - 35/240 -
Rear: 255/35 R 18 90 W - 39/270 - 36/250 - 42/290
Front: 225/40 R 18 88 Y 32/220 - 32/220 - 32/220 -
Rear: 255/35 R 18 90 Y - 39/270 - 33/230 - 39/270
Front: 225/35 R 19 88 Y XL 36/250 - 35/240 - 36/250 -
Rear: 255/30 R 19 91 Y XL - 44/300 - 38/260 - 44/300
with Sports package:
225/45 R 17 91 H M+S 32/220 38/260 32/220 36/250 35/240 42/290
225/45 R 17 94 V M+S XL 32/220 39/270 33/230 41/280 41/280 48/330
Front: 225/45 R 17 91 V 32/220 - 33/230 - 36/250 -
Rear: 255/40 R 17 94 V - 33/230 - 36/250 - 44/300
Front: 225/40 R 18 88 W 32/220 - 36/250 - 39/270 -
Rear: 255/35 R 18 90 W - 39/270 - 39/270 - 46/320
Front: 225/40 R 18 88 Y 32/220 - 32/220 - 35/240 -
Rear: 255/35 R 18 90 Y - 39/270 - 36/250 - 42/290
Front: 225/35 R 19 88 Y XL 36/250 - 36/250 - 39/270 -
Rear: 255/30 R 19 91 Y XL - 44/300 - 39/270 - 46/320
More details on the permissible load and weights can be found on page247. 

Mobility
 221Reference
At a glance
Controls
Driving tips
Communications
Navigation
Entertainment
heat when tested under controlled conditions 
on a specified indoor laboratory test wheel. 
Sustained high temperature can cause the 
material of the tire to degenerate and reduce 
tire life, and excessive temperature can lead to 
sudden tire failure. The grade C corresponds to 
a level of performance which all passenger car 
tires must meet under the Federal Motor Vehi-
cle Safety Standard No. 109. Grades B and A 
represent higher levels of performance on the 
laboratory test wheel than the minimum 
required by law.
The temperature grade for this tire is 
established for a tire that is properly 
inflated and not overloaded. Excessive speed, 
underinflation, or excessive loading, either sep-
arately or in combination, can cause heat 
buildup and possible tire failure.<
RSC – Run-Flat Tires
You will recognize Run-Flat Tires by a circular 
symbol containing the letters RSC on the side 
of the tire, refer to page222.
M+S
Winter and all-season tires. 
These have better winter properties than sum-
mer tires.
XL
Designation for specially reinforced tires.
Tire condition
Inspect your tires frequently for tread wear, 
signs of damage and for foreign objects lodged 
in the tread. Check the tread depth.
Minimum tread depth
The tread depth should not drop below 1/8 in/
3 mm, although, for example, European legisla-
tion only specifies a minimum tread depth of 
1/16 in/1.6 mm. At tread depths below 1/8 in/
3 mm there is an increased risk of high-speed 
hydroplaning, even when only small amounts of 
water are present on the road surface.
When winter tires wear down past a tread depth of 1/6 in/4 mm, they become perceptibly less 
suitable for winter conditions. In the interest of 
safety, new tires should be installed.
Wear indicators in the base of the tread groove 
are distributed around the tire's circumference; 
the letters TWI, for Tread Wear Indicator, on the 
tire's sidewalls identify tires that incorporate 
these wear indicators. Once the tire tread has 
worn down to the wear indicators, the tire has 
worn to a depth of 1/16 in/1.6 mm.
Wheel/tire damage
Please note that low-profile tires cause wheels, 
tires and suspension parts to be more suscep-
tible to road hazard and consequential dam-
ages.
Unusual vibrations encountered during normal 
vehicle operation can indicate tire failure or 
some other vehicle defect. This can, for exam-
ple, be caused by driving over curbs. The same 
applies to any other abnormal road behavior, 
such as pulling severely to the right or left.
In these cases, reduce speed immedi-
ately and have wheels and tires thor-
oughly checked. To do so, drive carefully to the 
nearest BMW center or tire shop that works 
according to BMW repair procedures with cor-
respondingly trained personnel. If necessary, 
have the vehicle towed there. 
Otherwise, tire damage can be extremely dan-
gerous for vehicle occupants and other road 
users.<
Tire age
For various reasons, such as the development 
of brittleness, BMW recommends tire replace-
ment after no more than 6 years, regardless of 
the actual wear of the tires. 

Mobility
 223Reference
At a glance
Controls
Driving tips
Communications
Navigation
Entertainment
Recommended tire brands
Certain makes of tire are recommended by 
BMW for each tire size. They are marked with a 
clearly visible BMW designation on the sidewall 
of the tire.
When properly used, these tires meet the high-
est standards in terms of safety and handling 
characteristics.
Special characteristics of winter tires
BMW recommends winter tires for use in cold 
winter driving conditions. Although all-season 
M+S tires provide better winter traction than 
summer tires, they generally fail to provide the 
same levels of cold-weather performance as 
winter tires.
Pay attention to speed
Always comply with the speed limit for the 
winter tires mounted on your car; failure 
to do so could result in tire damage and acci-
dents.<
If the car is capable of speeds higher than that 
permitted for the winter tires, a label stating the 
maximum permitted speed for the mounted 
tires must be displayed in your field of view. 
Specialist tire dealers and your BMW center 
can supply these labels.
Storage
Always store wheels and tires in a cool, dry 
place with as little exposure to light as possible. 
Always protect tires against all contact with oil, 
grease and fuels. 
Swapping wheels between axles
BMW advises against swapping wheels 
between the front and rear axles, even if all tires 
have the same size, as this could impair driving 
characteristics. If the tires are of mixed sizes, 
swapping wheels between the axles is not per-
missible.
Snow chains*
Only certain fine-link snow chains have been 
tested by BMW, classified as safe for use and 
recommended. Consult your BMW center for 
more information. 
Snow chains must be mounted in pairs and on 
the rear wheels only. Observe the manufac-
turer's instructions when mounting snow 
chains. Do not exceed a speed of 30 mph or 
50 km/h.
Do not initialize the Flat Tire Monitor if 
snow chains are mounted, otherwise the 
instrument might issue an incorrect reading.
When driving with snow chains, you may find it 
helpful to activate DTC temporarily, refer to 
page90.< 

Mobility
 225Reference
At a glance
Controls
Driving tips
Communications
Navigation
Entertainment
Important parts of the engine compartment
1Expansion tank for coolant, refer to 
page227
2Washer fluid filler neck for headlamp clean-
ing system and window washer system, 
refer to page653Jump-starting connection, refer to 
page237
4Filler neck for engine oil, refer to Adding 
engine oil
Engine oil
The engine oil consumption is dependent on 
driving style and driving conditions.
Checking oil level
Your car is equipped with an electronic oil-level 
monitor.
For a precise measurement and display of the 
oil level, it is necessary that the engine be at 
operating temperature, i.e. after uninterrupted 
driving for at least approx. 6.5 miles/10 km. You 
can have the oil level displayed while you are 
driving, or while the vehicle is at a standstill on a 
level surface and the engine is running.
Display in the instrument cluster
1.Push button 1 in the turn indicator lever up 
or down repeatedly until the appropriate 
symbol is shown in the display, accompa-
nied by the word "OIL".
2.Press button 2 in the turn indicator lever. 
The oil level is checked and the reading dis-
played. 

Mobility
 227Reference
At a glance
Controls
Driving tips
Communications
Navigation
Entertainment
more than 1 US quart/1 liter, refer also to 
Adding engine oil below.
>"Engine oil level too high"
Too much oil will harm the engine. 
Have the vehicle checked without 
delay.<
>"Please observe recalculated service inter-
val for engine oil"
Do not add engine oil. You can continue 
your journey. Note the newly calculated dis-
tance remaining to the next oil service, refer 
to page79. Have the system checked as 
soon as possible.
Adding engine oil
Do not add 1 US quart/1 liter of engine oil until a 
corresponding message is shown on the Con-
trol Display.
Add oil within the next 125 miles/200 km, 
otherwise the engine could be dam-
aged.<
Keep oils, greases, etc. out of the reach of 
children and comply with the relevant 
warnings on the containers. Otherwise, health 
hazards may result.<
Oil change
Have oil changed only at your BMW center or at 
a workshop that works according to BMW 
repair procedures with correspondingly trained 
personnel.
Specified engine oils
The quality of the engine oil selected has critical 
significance for the operation and service life of 
an engine. BMW continuously approves spe-cific oils after confirming their suitability for use 
in its vehicles with extensive testing.
Do not use oil additives as these may 
cause engine damage.<
Only use approved BMW High Performance 
Synthetic Oil.
If BMW High Performance Synthetic Oil is not 
available, you can add small quantities of other 
synthetic oils in between oil changes. Only use 
oils with the API SM specification or higher.
Your BMW center will be glad to answer 
any questions regarding BMW High Per-
formance Synthetic Oil or approved synthetic 
oils.<
You can also call BMW of North America at 
1-800-831-1117 or visit the website 
www.bmwusa.com to obtain this information.
Viscosity ratings
Viscosity is a measure of an oil's flow rating and 
is categorized in SAE classes.
Selecting the appropriate SAE class depends 
on the regional climatic conditions in which you 
normally drive your BMW.
Approved oils belong to the 5W-40 and 
5W-30 classes.<
These oils can be used for driving at all outside 
temperatures.
Coolant
Do not add coolant to the cooling system 
when the engine is hot. Escaping coolant 
can cause burns.<
Coolant consists of half water and half additive. 
Not all commercially available additives are suit-
able for your BMW. Ask your BMW center for 
suitable additives.
Only use suitable additives, otherwise 
engine damage may result. Because 
additives are harmful to your health, it is impor-
tant to follow the instructions on the contain-
ers.< 

Mobility
 229Reference
At a glance
Controls
Driving tips
Communications
Navigation
Entertainment
Maintenance
BMW Maintenance System
The BMW Maintenance System supports the 
preservation of the traffic and operating safety 
of your BMW. The objective is to optimize 
efforts with respect to minimal vehicle mainte-
nance costs.
If and when you come to sell your BMW, a com-
prehensive record of servicing will prove a sig-
nificant benefit.
CBS Condition Based Service
Sensors and special algorithms take the differ-
ent driving conditions of your BMW into 
account. Condition Based Service uses this to 
determine the current and future service 
requirements. By letting you define a service 
and maintenance regimen that reflects your 
own individual requirements, the system builds 
the basis for trouble-free driving.
On the Control Display, you can have the 
remaining times or distances for selected main-
tenance tasks and any legally prescribed dates 
displayed, refer to page79:
>Engine oil
>Brake pads: separately for front and rear
>Brake fluid
>Vehicle check
>Legally mandated inspections depending 
on local regulations
Service data in the remote control
Your vehicle continuously stores service-
requirement information in the remote control 
while you are driving. Your BMW Service Advi-
sor can read out this data from the remote con-
trol unit, and propose an optimized mainte-
nance approach. Whenever you take your car in 
for servicing you should therefore hand your 
BMW Service Advisor the remote control unit 
that you last used.
Make sure that the date is always set cor-
rectly, refer to page82; otherwise the 
effectiveness of Condition Based Service CBS 
is not assured.<
Service and Warranty Information 
Booklet for US models and Warranty 
and Service Guide Booklet for 
Canadian models
Please consult your Service and Warranty Infor-
mation Booklet for US models and Warranty 
and Service Guide Booklet for Canadian models 
for additional information on service require-
ments.
BMW recommends that you have service 
and repair operations performed at your 
BMW center. 
Take the time to ensure that these service pro-
cedures are confirmed by entries in your vehi-
cle's Service and Warranty Information Booklet 
for US models and Warranty and Service Guide 
Booklet for Canadian models. These entries 
verify that your vehicle has received the speci-
fied regular maintenance.< 

Mobility
 231Reference
At a glance
Controls
Driving tips
Communications
Navigation
Entertainment
Replacing components
Onboard tool kit
Coupe
The onboard tool kit is stored in a compartment 
on the right-hand side of the cargo bay. 
Remove the cover.
Convertible
The onboard tool kit is stored in a pouch under 
the cargo bay floor panel.
Wiper blades
1.Fold up the wiper arm.
2.Remove the cover. To do so, press the hook 
on the bottom, see arrow.3.Fold the wiper blade upwards.
4.Remove the wiper blade in the direction of 
the windshield, see arrow.
To avoid damage, make sure that the 
wiper arms are against the windshield 
before you open the engine compartment.<
Lamps and bulbs
Lamps and bulbs make an essential contribu-
tion to vehicle safety. They should, therefore, 
be handled carefully. BMW recommends hav-
ing your BMW center perform any work that you 
do not feel competent to perform yourself or 
that is not described here.
Never touch the glass of new bulbs with 
your bare fingers, as even minute 
amounts of contamination will burn into the 
bulb's surface and reduce its service life. Use a 
clean tissue, cloth or something similar, or hold 
the bulb by its base.<
You can obtain a selection of replacement bulbs 
at your BMW center.
Only change bulbs while they are cool to 
the touch, otherwise you could suffer 
burns.<
When working on electrical systems, 
always begin by switching off the con-
sumer in question, otherwise short-circuits 
could result. To avoid possible injury or equip-
ment damage when replacing bulbs, observe 
any instructions provided by the bulb manufac-
turer.< 

Mobility
 233Reference
At a glance
Controls
Driving tips
Communications
Navigation
Entertainment
3.Push the wire bracket out of the anchor 
towards the right and fold it up.
4.Disconnect the plug, change the bulb and 
reconnect the plug.
5.Insert the bulb.
6.Fold the wire bracket down and engage it.
7.Reattach the cover.
Tail lamps
Coupe
>Turn signal:
PY21W bulb, 21 watts
>Brake lamp in the luggage compartment lid:
H21W bulb, 21 watts
>Other lamps:
W16W bulb, 16 watts
The tail lamps are divided in two parts. One part 
is in the luggage compartment lid, the other is in 
the fender.
1Turn signal
2Roadside parking lamp/tail lamp, LED
3Backup lamp
4Brake lamp, consisting of two individual 
bulbs
5Brake Force Display lamp6Roadside parking lamp/tail lamp, LED
If one of the bulbs 2, 5 or 6 malfunctions, please 
contact your BMW center or a workshop that 
works according to BMW repair procedures 
with correspondingly trained personnel.
Convertible
>Turn signal:
PY21W bulb, 21 watts
>Brake lamp in the luggage compartment lid:
H21W bulb, 21 watts
The tail lamps are divided in two parts. One part 
is in the luggage compartment lid, the other is in 
the fender.
1Turn signal
2Roadside parking lamp/tail lamp, LED
3Backup lamp
4Brake lamp, consisting of two individual 
bulbs
5Brake Force Display lamp
6Roadside parking lamp/tail lamp, LED
If one of the bulbs 2 to 6 malfunctions, please 
contact your BMW center or a workshop that 
works according to BMW repair procedures 
with correspondingly trained personnel.
Fender-mounted lamps
Coupe
1.Left-hand side: use a screwdriver to pry off 
the cover in the cargo bay and remove the 
cover.
Right-hand side: remove the cover from the 
right-hand side panel of the cargo bay.