2008 AUDI Q5 high

Media drives11
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
Media drives
General notes on CD/DVD operation
These general notes apply to audio CDs and navigation
DVDs.
Requirements for good sound reproduction
Please note the following in order to ensure perfect high-quality
sound reproduction and avoid damage to media drives:
•Do not use damaged or scratched CDs or DVDs .
•Do not use single CDs (diameter 8 cm / 3 inches) .
•Do not use non-circular CDs (shape CDs) .
•Do not use labels .
•Do not use protective rings .
•Do not use dirty CDs or DVDs.
•Do not use a CD cover or a stabiliser.
•Always store unused CDs/DVDs in a suitable CD case and do not
expose them to direct sunlight.
Cleaning media drives, CDs and DVDs
Never use a CD player cleaning disc to clean the media drives.Clean CDs and DVDs with a soft, lint-free cloth. Wipe the disc in a
straight line from the centre outwards. If necessary, dirt can be
removed with a commercially available CD cleaner or with isopropyl
alcohol. Please never use petrol, paint thinner or record cleaner, as
these can damage CDs and DVDs.
Use of laser equipment
Laser devices are divided into the safety classes 1 to 4, as specified
by DIN IEC 76 (CO) 6/ VDE 0837. The audio devices used on your
vehicle are classified as safety class 1. Lasers used in devices that
fall into this category are very weak and well screened, so there is
no danger if used correctly.
Read errors
If the display indicates a read error, any of the following causes are
possible:
Note
•Under certain circumstances audio CDs that are copy-protected
or CDs that do not comply with the standard audio format cannot be
Fig. 2 CDs that should
not be used.
AA
AB
AC
AD
AE
ProblemRemedy
CD/DVD is dirty.Clean the CD/DVD.
CD/DVD is scratched.Replace the CD/DVD with a
scratch-free CD/DVD.
CD/DVD was inserted upside
down.Insert the CD/DVD with the text
facing upwards.
Condensation has formed on
the CD/DVD.Wait until the CD/DVD is dry.
A mechanical malfunction has
occurred on the media drive.Contact an Audi dealer or quali-
fied workshop.










Media drives 12
played. CDs that comply with the standard audio format have the
label “Compact Disc Digital Audio”.
•At extremely high or low outside temperatures, it is possible that
the playback of a CD/DVD will not function temporarily. A thermostat
switch is installed to protect the CD/DVD and the reading laser.
•Never remove the device cover. The device has no components
that can be serviced by the owner.
CD changer
Introduction
Eject button
CD slot
button
Position buttons with integrated diodes
The CD changer is located in the centre console. You can load
standard audio CDs or MP3/WMA CDs into the CD changer. The MMI
is used for playing CDs
page 63.
MP3/ WMA files must meet the following specifications:In the case of MP3 files with variable bit rate the display of elapsed
playing time may deviate from the actual figure.
Please note that music files are copyright-protected.
Note
•Please observe the notes for handling CDs
page 11.
•The CD changer does not support playlists and DRM-protected
files.
•In view of the variety of CD-Rs and CD-RWs and the difference in
memory capacities, the quality of this function may vary in the case
of some memory media.
Loading CDs
Do not use any force when inserting a CD into the drive. The
CD will be drawn into the slot automatically.
Fig. 3 CD changer
A1
A2
A3LOAD
A4
MP3 filesWMA files
FormatMPEG-1 Layer 2 and 3
MPEG-2 Layer 2 and 3Version 7, 8 and 9
StandardISO 9660 Level 1 and 2
File systemJoliet (single session and multisession)
Bit rates32 to 320 kbit/s and variable bit rate
Number of
files and
directoriesMax. 255 files per directory, max. 255 directories;
in total not more than 512 files and directories
per medium
ID3 tags/
WMA tagsVersion 1, 1.1, 2.2, 2.3
and 2.4,
max. 30 charactersVersion 7, 8 and 9,
max. 30 characters
Supported
mediaCD-ROM, CD-R, CD-RW with a capacity of 650 MB
and 700 MB











Media drives15
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
Note
Please observe the notes on handling navigation DVDs
page 11.
Audi music interface
Applies to vehicles: with Audi music interface - under development at the time of printing
Introduction
Various portable players can be connected to the Audi
music interface.
Connection on Audi music interface
Storage bayCover cap
Connector plug for Audi music interface
Adapter cable* (e.g. iPod adapter cable*)
Sliding storage tray
iPod connector on iPod adapter cable*
iPod
iPod adapter cable*
Stereo adapter cable with 3.5 mm jack plug*
Mini USB adapter cable*
USB adapter cable*
The Audi music interface is located in the glove box. You can
connect your portable player (e.g. MP3 player) to the Audi music
interface using special adapter cables*. The adapter cables* are
available from Audi dealers or specialist retailers.
Caution
Very high or very low temperatures (a common occurrence in a car's
interior) can cause damage to the portable player and/or impair its
performance.
•Please do not leave your portable player in the vehicle in case of
extreme temperatures.
Applies to vehicles: with Audi music interface and adapter cable - under development at the
time of printing
Connecting an adapter cable to the Audi
music interface
– Open the glove box.
–Open the cover cap
fig. 5.
– Connect the adapter cable to the Audi music interface

fig. 5.
Fig. 5 Audi music
interface with iPod
adapter cable and iPod
Fig. 6 Audi music
interface: Adapter
cable
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A3










Phone pre-installation19
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
Phone pre-installation
Applies to vehicles: with phone pre-installation
Introduction
A mobile phone can be connected to the on-board phone
system and operated via the MMI control console, the
multi-function steering wheel or the speech control
system.
The phone pre-installation is located in the centre armrest. A special
mobile phone adapter is needed in order to connect your mobile
phone to this interface
page 20. Mobile phone adapters are avail-
able from Audi dealers or specialist retailers.
You can operate your mobile phone using the MMI control console

page 87, the multi-function steering wheel*
page 132, the
speech dialogue system*
page 169 or the telephone speech
control system*
page 160. You can also use the talk button *
on the mobile phone adapter to answer and end a call.
When your mobile phone is in the mobile phone adapter, call
signals are sent and received via the external car aerial. This ensures
good transmission quality and reduces radiation emissions in the
interior of the vehicle.
WARNING
•Please note that persons should maintain a minimum distance
of 15 cm from the aerial as prescribed by the certification regula-
tions for mobile high frequency transmission devices.
•Please direct your full attention to the road at all times! As the
driver, you have full responsibility for the safety of the vehicle and
other road users. For this reason, you should only use the func-
tions in a manner that allows you to maintain control of the
vehicle in all situations - accident risk!
•The speech dialogue system*
page 169 and the telephone
speech control system*
page 160 must not be used in cases of
emergency, since the voice changes in stressful situations. This
could result in a failed or delayed telephone connection. Always
dial emergency numbers manually!
Caution
•Always obey the laws regulating the use of telephones in vehi-
cles.
•Always switch off your telephone in areas where using mobile
phones is prohibited.
•Switch off the telephone in all areas where there may be a risk of
explosion. Remember that these areas may not always be
adequately marked. Such places are filling stations, fuel and chem-
ical storage facilities or transport vehicles and other places where
fumes, chemicals (e.g. from leaking propane or fuel vapours in vehi-
cles or buildings) or large quantities of dust particles (e.g. from flour
or wood) could accumulate in the air. This warning also applies to
all other places where you would normally switch off your engine.
Note
•In order to use the telephone functions, your mobile phone must
be compatible with the phone pre-installation in the vehicle, and the
functions must be supported by your service provider.
•For up-to-date information on the phone pre-installation, please
ask an Audi dealer or specialist retailer.


WARNING (continued)










Basic operation 42
MMI display
“Standard” menus
After pressing a function selector button
page 41, a menu will
appear in the MMI display.
Fig. 30 Setup Naviga-
tion
Fig. 31 Radio
submenu
LegendSymbol /
MarkingExplanation
Heading
Selected mode (e.g. radio
fig. 31).
Display in Setup menu: Setup menu in
the selected mode (e.g. Setup Naviga-
tion
fig. 30).
In vehicles with a telephone* the net-
work provider and, if applicable, the
roaming symbol
 will be shown.
TMC symbolsReception of TMC traffic messages

page 121.
Arrows
pointing
up/downIndicate further menu options
(next/previous page).
CursorPoints to the item selected in a menu.
Selected
optionA selected item is highlighted in white.
Selection boxSelection possibilities for selected
item.
ArrowIndicates more selection or setting
possibilities.
Temperature
display*Selected temperature setting in vehi-
cles with automatic air conditioner*.
Signal
strength indi-
cator*Quality of mobile phone connection,
or
PIN: Entering PIN
page 88
PUK: Entering PUK
page 88
SIM: Inserting SIM card
Envelope*
Unread text message
page 100.
Crossed-out envelope: No more text
messages can be received (SIM card
memory is full)
page 100.
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10











Basic operation 44
Entering letters, numbers and symbols using
the speller
You can find an overview of the speller on
page 43.
Entering letters, numbers and symbols
– Turn the rotary pushbutton and select the letter, number
or symbol with the cursor . The selected figure will
appear larger in the selection ring .
– To apply the letter, number or symbol, press the rotary
pushbutton. Your entry will appear in the entry space .
– After entering all the characters, turn the rotary push-
button to OK and press the rotary pushbutton.
Deleting letters, numbers and symbols
– Turn the rotary pushbutton and use the pointer to select
DEL .
– To delete the last character in the entry space, press the
rotary pushbutton.
– To delete all characters in the entry space, press and hold
the rotary pushbutton until no characters are displayed
in the entry space.
In some cases (such as when using the navigation* function) certain
letters are not available for selection if they are an illogical option.
This means that you can only select those letters that are offered as
a logical possibility for this entry.
Use the speller for numbers to enter special characters (such as a
dash or full stop).
LegendSymbol /
MarkingExplanation
Po i n t e rTo highlight the selected item in white
and make it appear larger in the selec-
tion ring.
DELTo delete the character to the left of
the highlighted cursor.
To move the cursor in the entry space
forwards and backwards.
OKTo confirm a completed entry.
A...ZTo switch the speller from numbers to
letters.
Cursor
Entry space
Selection ringTo enlarge the character selected with
the cursor.
To switch from lower case to upper
case letters.
LISTTo show a list of suggestions.
0..9To switch the speller from letters to
numbers.
SpaceTo enter a space in the entry space.
List of sug-
gestionsTo show suggested entries in alpha-
betical order.
Indicates additional list entries.
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A1
A8
A7
A4
A2










Basic operation45
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
Switching the MMI display on and off
Switching off the display
– Starting from any one of the Setup menus, press the
control button for Display.
– Turn the rotary pushbutton to Switch off display

fig. 34 and press the rotary pushbutton. The display
will be switched off.
Switching on the display
– Press or turn the rotary pushbutton, or
– Press a function selector button, or
– Press a control button, or
– Press the button.
Note
After switching off the display, you can still change the station on a
selected audio/video source using the arrow buttons on the MMI
control console.
Adjusting the volume
Current audio/video* source
Adjust the volume or mute the audio sources using the
ON/OFF button.
Increasing and reducing the volume
– Turn the ON/OFF button clockwise or anti-clockwise. The
volume level you select is stored in the memory.
Mute
– Briefly press the ON/OFF button. A crossed-out loud-
speaker will appear in the MMI display.
Unmute
– Briefly press the ON/OFF button, or
– Turn the ON/OFF button.
When you switch on the MMI system, very high/very low volume
levels are automatically reduced/increased to a preset level.
If you activate the mute/pause function by pressing the ON/OFF
button briefly before switching off the MMI, the mute/pause func-
tion will remain active when the MMI is switched on again.
Fig. 34 Switching off
the MMI display
RETURN
Fig. 35 Increasing,
reducing and muting
volume of MMI system










Basic operation49
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
– Press the rotary pushbutton to confirm your
adjustment.
Setting the time
You can choose between a quartz clock and a radio-
controlled clock*. If you have chosen the quartz clock,
you must set the time and date yourself. The radio-
controlled clock* receives the time and date automati-
cally.
Calling up the Time setting menu
– Press the function selector button marked .
– Press the Time control button. The Time setting menu
will appear on the MMI display.
Selecting the time source*
7)
– Turn the rotary pushbutton to Time source and press to
confirm.– Turn the rotary pushbutton to quartz or radio clock* and
press to confirm. When the time source is selected as
radio clock*, the “signal reception symbol” appears on
the rev counter display.
Setting the time (only possible for time source:
quar t z)
– Turn the rotary pushbutton to Time and press to confirm.
The hour display will be highlighted in white on the MMI
display.
– To set the hour, turn the rotary pushbutton clockwise or
anti-clockwise and press it. The minute display will then
be highlighted in white on the MMI display.
– To set the minutes, turn the rotary pushbutton clockwise
or anti-clockwise.
– Confirm the time setting by pressing the rotary push-
button.
Setting the date (only possible for time source:
quar t z)
– Turn the rotary pushbutton to Date and press the rotary
pushbutton. The date display will then be highlighted in
white on the MMI display.
– To set the day, turn the rotary pushbutton clockwise or
anti-clockwise and press it. The month display will then
be highlighted in white on the MMI display.
– To set the month, turn the rotary pushbutton clockwise
or anti-clockwise and press it. The year display will then
be highlighted in white on the MMI display.
– To set the year, turn the rotary pushbutton clockwise or
anti-clockwise.
7)Applies to vehicles with radio-controlled clock
Fig. 41 Time setting
SETUP