2008 AUDI A4 mode

Playing media 64
Selecting a CD
The CDs in the CD changer can be selected from the MMI
control console.
Important: CD mode must be activated
page 63.
– Press the control button for Changer.
– Turn the rotary pushbutton to select a CD
fig. 55.
– Press the rotary pushbutton to confirm the CD. The CD
will then be played.
Note
A CD can also be selected directly by pressing a position button on
the CD changer
page 13.
Selecting a folder
The folders on an MP3 CD or a connected portable player*
appear on the MMI display.
Important: An MP3/ WMA CD must be inserted into the CD
changer
page 12 and must be playing, or the Audi music
interface* must be activated
page 63.
– Press the function selector button marked . The
structure of the folders on an MP3 CD or a connected
portable player will appear on the MMI display
fig. 56.
– Turn the rotary pushbutton to mark a folder.
– Press the rotary pushbutton to select the folder. The
content of the folder will appear.
Note
•An empty playlist folder will appear in grey lettering.
•The Compilations folder available in the iPod does not appear on
the MMI display.
Fig. 55 List of CDs in
the CD changerFig. 56 Track list of a
folder
MEDIA





!




Television71
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
Television
Applies to vehicles: with analog TV and DVB-T
Introduction
For safety reasons, the TV picture is not available while
the vehicle is moving.
Via the MMI system you can receive either analog TV channels or
digital TV channels as well as digital radio stations 9) in the DVB-T
standard.
Your MMI system automatically displays a list of the available TV
channels. You do not even have to set up the channels. Use the
rotary pushbutton in the usual way to select the TV channels.
However, which and how many channels you can receive depends
on your location and the quality of the reception.
DVB-T channels/stations can primarily be received in big metropol-
itan areas. Reception is dependent on a number of factors, e.g. the
distance to the transmitter and the speed at which the vehicle is
travelling.
Would you like to connect additional AV devices to your MMI
system? No problem! You can connect up to two AV devices
(audio/video out port). You only have to set the appropriate AV
standard
page 79. Suitable connector cables are available from
Audi dealers or specialist retailers.
The picture is at first only shown within the inner section of the
display; however, after a few seconds it will expand to the full
screen. The volume will automatically be muted if the TV reception
becomes poor. The volume will be switched on again automatically
if the TV reception quality improves. While you are driving, the
screen will be darkened for your safety. However, you can still listen
to the audio.
Note
•The analog/digital TV reception only supports the DVB-T
standard. Other standards such as DVB via satellite (DVB-S) or
encoded programmes / Pay TV are not supported.
•Playback of multi-channel programmes in Dolby Digital 5.1
sound is not supported. These programmes are then reproduced in
stereo.
•The DVB-T network is still in the process of expanding and is
therefore not available in all areas. Please obtain information
regarding DVB-T reception in the region you live in.
•You can operate the DVB functions via the MMI if the DVB-T
receiver was fitted at the factory.
Applies to vehicles: with analog TV and DVB-T
Activating TV mode
Important: The MMI system must be switched on

page 40, and the vehicle must be stationary.
– Press the function selector button marked .
9)Digital radio stations can only be received via DVB-T in some countries and
regions.
Fig. 62 List of possible
audio/video sources
MEDIA










Television 72
– If the list of TV channels
fig. 63 does not appear on the
MMI display, press the control button for Source

page 71, fig. 62.
– Turn the rotary pushbutton to TV
page 71, fig. 62.
– Press the rotary pushbutton to confirm TV as the source.
TV mode will be activated.
Note
The television playback will be interrupted by traffic announce-
ments if the Traffic Programme function is active
page 58.
Applies to vehicles: with analog TV and DVB-T
Selecting a TV channel
All TV channels that can currently be received appear in a
list in alphabetical order.
Important: TV mode must be activated
page 71.
– Briefly turn the rotary pushbutton when the picture has
expanded to the full MMI screen. A list of TV channels
and digital radio stations will be displayed.– Turn the rotary pushbutton to select a TV channel

fig. 63.
– Press the rotary pushbutton to confirm the TV channel.
To be able to distinguish between the analog and the digital TV
channels, the digital TV channels are marked with DVB. The digital
radio stations are marked with DVB audio.
TV channels that are broadcast without a name are listed by their
channel number (e.g. digital channel: DTV 60-01; analog channel:
Ch. 32) in the channel list.
Note
Selecting a TV channel on the multi-function steering wheel is even
easier
page 132. You can also change the channel by pressing the
arrow buttons on the MMI control console.
Applies to vehicles: with DVB-T
Display in the MMI system
Fig. 63 Channel list
Fi g . 6 4 I n fo b a r o f a T V
channel











Television73
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control Info bar
After changing the channel or updating the contents, an info bar
will briefly be displayed.
Depending on availability, the info bar of a TV channel/radio station
can indicate:
Time at which the current programme starts and ends
Identification of digital (DVB-T) or analog channel
Channel name
Name of current programme
EPG availability
Teletext availability
Current audio format - dual channel sound (sound channel)
Current audio format - stereo
No symbol is displayed for the audio format Mono.
Interference
Short periods of interference on digital channels are indicated by a
freeze frame, muting of the volume and a radio tower symbol with
a crossed-out loudspeaker symbol. Long periods of interference or
no DVB-T reception are indicated by the blacking out of the MMI
display, muting of the volume, the radio tower symbol and the
symbol for signal disruption.When the signal for analog channels becomes weaker, the sound
quality worsens (hiss). No TV reception is indicated by the radio
tower symbol with the symbol for signal disruption.
A channel selected from the memory list that cannot be received is
marked with the tower radio symbol, the symbol for "No TV recep-
tion", the blacking out of the MMI display and muting of the volume.
Thermal cut-out
The thermal cut-out of the television receiver switches the picture
and sound off temporarily if the outside temperature is unusually
high. A thermometer will appear in the MMI display.
Applies to vehicles: with analog TV and DVB-T
Selecting TV channels
The automatic channel search selects channels with good
reception.
Important: TV mode must be activated
page 71.
Selecting the next available channel
– Briefly turn the rotary pushbutton when the picture has
expanded to the full MMI screen. A list of TV channels will
appear.
Fi g . 6 5 I n fo b a r o f a T V
channel
A1
A2
A3
A4
A5
A6
A7
A8
Fig. 66 Selecting chan-
nels manually (up)





 




Using the telephone 90
WARNING
Since your telephone operates via radio waves, a connection
cannot be guaranteed under all circumstances. Do not rely solely
on your telephone when a vital communication (e.g. medical emer-
gency) is involved.
Note
You can also place an emergency call using the handset*

page 147.
Dialling a telephone number
Applies to vehicles: with Bluetooth car telephone kit or phone pre-installation
Directly via the speller
Using the speller, you can enter a telephone number
directly (as a series of numbers or as a series of letters).
Important: The telephone mode must be activated

page 26, and the speller must be displayed on the MMI
display
fig. 83.
Entering a telephone number using numbers
– Enter the telephone number via the speller.
– To confirm your entry turn the speller to OK and press the
rotary pushbutton, or
– Press the control button for Dial. After the connection
has been established, the audio system will be muted.
Entering a telephone number using letters
– Enter a code, e.g. 0800 via the speller
fig. 83.
– To switch to the speller for letters, turn the speller to A-Z

fig. 83 and press the rotary pushbutton. The speller
for letters will appear on the MMI display
fig. 84.
– Enter a series of letters, e.g. AUDISERVICE via the speller

fig. 84.
– To confirm your entry turn the speller to OK and press the
rotary pushbutton, or
Fig. 83 Entering a tele-
phone number via the
speller for numbers
Fig. 84 Entering a tele-
phone number via the
speller for letters
A1










Using the telephone91
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control
– Press the control button for Dial. The telephone number
entered will be dialled.
Should you have entered a telephone number incorrectly, you can
delete the telephone number you have entered into the speller by
pressing the control button .
Note
•DTMF tones can be entered directly using the speller or loaded
from the telephone numbers stored in the memory lists
page 91.
•The audio source is muted automatically when you make or
receive telephone calls. The mute symbol
page 42, fig. 31 will
then appear in the status line.
•If you activate the voice guidance option off (phone)* in the navi-
gation* function you will not hear any navigation cues while you are
talking on the telephone*
page 119.
•If the MMI display was switched off, it will be switched on auto-
matically for the duration of the telephone call.
Applies to vehicles: with Bluetooth car telephone kit or phone pre-installation
From a list
Important: The telephone mode must be activated

page 26.
Finding and calling a telephone number from a
list
– Press the Memory control button.
– Turn the rotary pushbutton and select Numbers dialled,
Directory, Phone book, Received calls or Missed calls.
– Press the rotary pushbutton. The telephone numbers in
the selected list will appear in the MMI display.
– Turn the rotary pushbutton to the telephone number you
wish to select.
– Press the rotary pushbutton. The selected telephone
number will be entered into the speller automatically.
– To start the call, turn the speller to OK and press the
rotary pushbutton, or
– Press the control button for Dial.
Calling up the Numbers dialled list (shortcut) and
calling a number
– Press the function selector button marked . The
speller will appear on the MMI display. There will be no
phone number in the entry space of the speller.
– Press the control button for Dial. The Numbers dialled list
will appear in the MMI display.
– Turn the rotary pushbutton to the telephone number you
wish to select.
– Press the rotary pushbutton. The selected telephone
number will be entered into the speller automatically.
RETURN
Fig. 85 Selecting a
telephone number
from a list
TEL










Using the telephone 96
Switching between calls*13)
You can switch between two phone calls (one of them will be on
hold at any given time). The MMI display shows the active call, the
call on hold and the length of time for the connection.
Press the control button for End call to end whichever call is
currently active. The call on hold will remain in the hold queue.
Conference calling*
13)
Up to five callers can take part in a conference (depending on the
network service).
Select Join conference
page 95, fig. 89 to set up a conference. The
call on hold and the active call are added to the conference.
To set up a further call, select Hold to place all the members of an
existing conference on hold. Then press the control button for
Options or the button on the control console to close the
Options menu. Now enter a telephone number using the speller

page 90, fig. 83. Select OK or Dial to start dialling. To add this
caller to the existing conference, select Conference.
Select Resume if you want to retrieve all callers of an existing
conference from the hold queue. The Show conference participants

page 95, fig. 90 option allows you to display the callers.
Note
•The option Call waiting must be activated for you to be made
aware of incoming calls during a conversation
page 97. This
option depends on your mobile network service provider.
•The options available during a call may vary depending on the
mobile network service provider.
Applies to vehicles: with Bluetooth car telephone kit
Telephone settings
– Select: Function selector button > function selector
button > Telephone settings.
Set ring tone*14)
The selected ring tone is played and is stored when you close the
submenu.
Bluetooth settings*
•Search for mobile phone*14) - to find and list any Bluetooth
mobile phones within range.
•Bluetooth devices - to display a list of Bluetooth devices bonded
to the MMI system. The Bluetooth symbol marks the Bluetooth
device which contains the SIM card and which is actively connected.
•Delete ext. Bluetooth dev. - to delete all bonded mobile phones.
Bonded handsets* (e.g. “AUDI BTHS”) have to be deleted one at a
time. To delete bonded Bluetooth devices one at a time, choose a
device and select Delete this device.
•Bluetooth name - to change the name of the vehicle base station
on your car telephone kit (“AUDI BTA”).
•PIN for handsfree mode15) - to change the factory default (1234).
This PIN number has to be entered when you bond a mobile phone
with the Hands-Free Profile
page 28.
•Discoverability - to switch the car telephone discoverability on or
off. This setting determines whether the vehicle base station can be
detected by a mobile phone or handset*. If you select auto, the
vehicle base station can be discovered by mobile phones or the
handset* for a period of about five minutes while the car is
stationary and the key is in the ignition. Discoverability is switched
off after this period. Mobile phones which have already been
bonded can connect via Bluetooth even when discoverability is
RETURN
14)Applies to mobile phones with SIM Access Profile.15)Applies to mobile phones with Hands-Free Profile.
TEL
SETUP





!




Using the telephone101
MMI componentsMMI control consoleMulti-function steering wheelTelephone handsetVoice control Options
20)
The following functions are available under Options when you open
a text message to read it:
•Delete - to delete the open text message.
•Call - to dial the number of the person who sent the text
message.
•Extract number - to copy a telephone number contained in the
open text message into the speller for editing.
Note
•A crossed-out envelope symbol in the status line indicates that
there is not enough memory space available for new text messages.
In this case, you will have to delete one or more text messages from
the SIM card before you can receive further text messages.
•You can write and send text messages using the handset*

page 154.
Other settings for the phone pre-
installation
Applies to vehicles: with phone pre-installation
Options during a call
Important: You must be talking on the phone
page 90.
– Select: Control button Options > Mike off.
Switching microphone on/off
Your caller cannot hear your private conversations when the micro-
phone is off. You can still hear the caller. Mike off appears in the
MMI display.Replacing a call
If you are already talking on the phone when someone else calls, the
options Replace and Ignore will appear on the MMI display.
If you select Replace, the active call will be replaced by the incoming
call. If you select Ignore, the incoming call will be declined.
The display in the MMI may remain for several seconds afterwards
(depends on your type of phone). Should you use the function
Replace or Ignore in the MMI system during this time, it is possible
that the current call will be ended.
Note
The option Call waiting must be activated on your mobile phone for
you to be made aware of incoming calls during a conversation. The
call options depend on your mobile network service provider.
Applies to vehicles: with phone pre-installation
Telephone settings
– Press the > buttons on the MMI control
console and select Telephone settings on the MMI.
Bluetooth settings
•PIN for handsfree mode - to change the factory default (1234).
This PIN number has to be entered when you bond a Bluetooth
mobile phone with the Hands-Free Profile to the on-board phone
system
page 22.
•Remove Bluetooth devices - to delete all bonded mobile phones.
Default settings
The on-board phone system is returned to the factory defaults. This
will delete your user data, including the phone books stored in the
memory
page 23, any bonded Bluetooth devices
page 22 and
your mailbox number.
TELSETUP