2008 Alfa Romeo GT lock

IN AN EMERGENCY
213
IF THE CAR IS TO BE TOWED
The tow ring supplied with the car is
housed in the tool box under the boot mat.
To install the tow ring, proceed as follows:
– Take the tow ring from the tool box.
– Remove the cover (A) snap-fitted on
the front (fig. 55) or rear (fig. 56)
bumper. To do this, using the flat-bladed
screwdriver provided, protect the tip with a
soft cloth to avoid damaging the car.– Firmly screw the ring in its housing.
fig. 55 - front
A0A0650b
fig. 56 - rear
A0A0670b
Before tightening the ring
carefully clean the thread-
ed housing. Before begin-
ning to tow the car, make sure that
the ring is firmly tightened in its
threaded housing.
Before starting to tow,
turn the ignition key to
MAR and back to STOP,
again without removing it. Re-
moving the key automatically en-
gages the steering lock resulting in
the impossibility to steer the
wheels. When towing remember
that without the help of the engine
brake and power steering greater
effort is required on the pedal and
steering wheel. Do not use flexible
cables for towing and avoid jerks.
During towing operations make
sure that fastening the joint to the
car does not damage the compo-
nents in contact with it. When tow-
ing the car, it is compulsory to fol-
low specific traffic regulations con-
cerning both the towing device and
behaviour on the road.

IN AN EMERGENCY
215
– In motorways pileups, especially with
poor visibility, the risk of being involved in
other crashes is high. Leave the car imme-
diately and go beyond the guard-rail.
– If doors are blocked, do not try to get
out of the car breaking the windscreen which
is stratified. The windows and rear screen
are easier to break.
– Remove the ignition key of the cars in-
volved.
– If you note a smell of fuel or other chem-
ical products, do not smoke and have a cig-
arette stubbed out.
– To put out fires, even small ones, use
the extinguisher, blankets, sand, or earth.
Never use water.
– If use of the lighting system is not nec-
essary, disconnect the battery negative ter-
minal (–).IN THE EVENT
OF AN ACCIDENT
– It is important to keep calm.
– If you are not directly involved, stop at
least a few dozen metres away from the ac-
cident.
– On motorways, stop without blocking
the emergency lane.
– Turn the engine off and the hazard warn-
ing lights on.
– At night, illuminate the place of the ac-
cident with the headlights.
– Take care, do not risk being run over.
– Signal the accident placing the triangle
at regulation distance in a clearly visible
place.
– Call the emergency organisation, giving
the most accurate information possible. On
motorways use the special phones provid-
ed.
IF PEOPLE ARE INJURED
– An injured person must never be aban-
doned. Helping is compulsory also for per-
sons not directly involved in the accident.
– Do not crowd around injured people.
– Reassure the injured person that help
is on the way, and stay near to overcome
any panic.
– Release or cut the seat belt restraining
injured persons.
– Do not give injured persons anything
to drink.
– An injured person should never be
moved except in the following circum-
stances.
– Remove an injured person from the car
only in danger of fire, sinking or falling.
When removing an injured person: do not
pull the limbs or bend the head and keep
the body as horizontal as possible.
FIRST AID KIT
In addition to the first-aid kit, it is also
wise to keep an extinguisher and a blan-
ket in the car.

CAR MAINTENANCE
217
SCHEDULED MAINTENANCE PROGRAMME
20 40 60 80 100 120 140 160 180Thousands of km
Check tyre conditions/wear and adjust pressure if necessary
Check operation of lighting system (headlights, direction indicators,
hazard warning lights, boot, passenger compartment, glovebox lights, warning lights, etc..)
Check operation of windscreen washer system, adjust spray jets
Check position/wear of windscreen/rearscreen wiper blades
Check operation of front disk brake pad wear indicator
Check wear conditions of rear disk brake pads
Sight check the conditions of: body exterior, underbody protection, stiff pipes
and hoses (exhaust - fuel supply - brakes), rubber parts
(boots - sleeves - bushes etc..)
Check cleanness of locks, bonnet and boot and lever cleanness, and lubrication
Sight inspect accessory drive belt conditions
Check handbrake lever stroke adjustment
Check antievaporation system (petrol versions)
Change air cleaner cartridge (petrol versions)
Change air cleaner cartridge (JTD versions)
Top up fluid levels (engine coolant, brakes, windscreen washer, battery, etc..)
●●●●●●●●●
●●●●●●●●●
●●●●●●●●●
●●●●●●●●●
●●●●●●●●●
●●●●
●●●●●●●●●
●●●●●●●●●
●●
●●●●
●●
●●●●
●●●●●●●●●
●●●●●●●●●

CAR MAINTENANCE
219
ADDITIONAL
OPERATIONS
Every 1000 kmor before long journeys,
check and if necessary top up:
– engine coolant fluid level
– brake/hydraulic clutch control fluid level
– power steering fluid level
– windscreen washer and headlamp wash-
er fluid level
– tyre pressure and conditions.
Every 3000 kmcheck and if necessary
top up the engine oil level.
The use of FL Seleniaproducts is rec-
ommended which have been designed and
made expressly for Alfa Romeo cars (see
“Refuelling” in the “Technical Specifica-
tions” chapter).
ANNUAL INSPECTION
PROGRAMME
For cars with an annual mileage
of below 20,000 km (for example
about 10,000 km) the following
yearly inspection programme is ad-
vised:
– Check tyre conditions/wear and if nec-
essary adjust the pressure (including spare
wheel)
– Check operation of lighting system
(headlights, direction indicators, hazard
warning lights, boot, passenger compart-
ment, glovebox lights, warning lights, etc.)
– Check operation of windscreen wiper
system, spray jet adjustment
– Check windscreen blade position/wear
– Check front disk brake pad conditions
and wear
– Check cleanness of bonnet and boot
locks, and lever cleanness and lubrication.– Sight check for conditions of: engine,
gearbox, transmission, pipes (exhaust - fu-
el supply - brakes), rubber parts (boots -
sleeves - bushes etc..), brake and fuel sup-
ply system hoses
– Check battery charge
– Sight check for conditions of various dri-
ve belts
– Check and if necessary top up fluid lev-
els (engine coolant, brakes, windscreen
washer, battery etc. )
– Change engine oil and oil filter
– Change pollen filter.

CAR MAINTENANCE
227
Oil consumption is very
low; if topping up again is
needed shortly afterwards,
have the system checked for pos-
sible leaks by Alfa Romeo Autho-
rised Services.Do not allow the power
steering fluid to touch hot
parts of the engine: it is in-
flammable.
fig. 12
A0A0217b
fig. 11
A0A0400b
BRAKE AND HYDRAULIC
CLUTCH FLUID
(fig. 12)
Check that the fluid level in the reservoir
is at maximum. Top up with the brake fluid
specified in the table “Fluids and lubricants”
(see section “Technical specifications").
NOTEClean accurately the tank cap A
and the surrounding surface. When opening
the cap take the utmost care to prevent im-
purities entering the tank. When topping up,
always use a funnel with built-in filter with
mesh equal to or lower than 0.12 mm.
IMPORTANTFor this operation it is
however recommended to contact Alfa
Romeo Authorised Services.
POWER STEERING FLUID
(fig. 11)
Check that the level of the oil in the reser-
voir is at maximum.
This operation should be carried out with
the car on a level surface and the engine
switched off and cold.
Check that the level reaches the MAX
mark on the reservoir or coincides with the
upper notch (maximum level) on the dip-
stick (A) integral with the reservoir cap.If the oil level in the reservoir is below the
specified one, top up only with one of the
products listed in the “Fluids and lubricants”
table in the “Technical specifications” chap-
ter proceeding as follows:
– Start the engine and wait for the oil lev-
el in the reservoir to stabilise.
– With the engine running, turn the steer-
ing wheel lock to lock a few times.
– Top up to the MAXlevel notch, then
refit the cap.

CAR MAINTENANCE
239
Do not keep aerosol cans
in the car. There is the risk
they might explode. Aerosol
cans must never be exposed to a
temperature above 50°C. The tem-
perature inside the car might go well
beyond that figure when exposed
to the sun’s rays.
INTERIOR PLASTIC PARTS
For routine cleaning of interior plastic parts
use a soft cloth moistened with water and
neutral soap. Remove grease or persisting
stains using appropriate solvent-free prod-
ucts designed to preserve appearance and
colour of plastic components.
IMPORTANTNever use spirit or petro-
leum to clean the glass of the instrument
panel or other plastic components.
STEERING WHEEL/GEAR LEVER
KNOB WITH GENUINE LEATHER
COVERING
These components shall only be cleaned
with water and neutral soap. Never use spir-
it or alcohol-based products.
Before using special products for cleaning
interiors, read carefully label instructions and
indications to make sure they are free from
spirit and/or alcohol-based substances. If
when cleaning the windscreen with special
glass products, some drops fall on the
leather covering of the steering wheel/gear
lever knob remove them immediately and
then clean with water and neutral soap.
IMPORTANTTake the utmost care
when engaging the steering lock to prevent
scratching the leather covering.
CLEANING LEATHER SEATS
– Remove dried on dirt with a lightly
moistened chamois leather or cloth with-
out pressing too hard.
– Remove liquid and grease stains with
a dry absorbent cloth without rubbing. Then
wipe with a soft cloth or chamois leather
with water and neutral soap. If the stain per-
sists, use specific products, carefully follow-
ing the instructions for use.
IMPORTANTNever use spirit or alco-
holbased products, even in small percentage.
Fabric upholstery of your
car is purpose-made to
withstand common wear
resulting from normal use of the
car. It is however absolutely nec-
essary to prevent hard and/or pro-
longed scratching/scraping caused
by clothing accessories like metal-
lic buckles, studs, “Velcro” fixings,
etc. that stressing locally the fabric
could break yarns and damage the
upholstery as a consequence.

TECHNICAL SPECIFICATIONS
244
FRONT WHEEL DRIVE WITH
SELF-LOCKING DIFFERENTIAL
(upon request for versions/
markets where applicable)
Alfa Q2characteristics are such as to
guarantee top performance with whatever
road condition.Alfa Q2features front wheel drive with
front mechanical self-locking differential LSD
(Limited Slip Differential). Torque level be-
tween right and left wheel is modulated ac-
cording to the TORSEN Bfront differen-
tial grip. Mechanical modulation is continu-
ous and gradual thus optimizing drive under
whatever running condition and guarantee-
ing smooth drive, high stability and keeping
top comfort conditions.This type of differential enables to exploit
the tyre-road grip at the best even under
poor grip conditions: the driver is however
charged with observing common safety rules
since road safety is always the driver's re-
sponsibility.

RIGHT HAND DRIVE VERSION
257
DASHBOARD
fig. 1
A0A0724b
1.Adjustable side air vents - 2.Fixed side window air vents -3.Front passenger’s air bag - 4.Tailgate release button - 5.Cards holder (for versions/mar-
kets where applicable) - 6. Sound system (for versions/markets where applicable) -7.Adjustable central air vents - 8.Upper fixed vent - 9.Glass/can
holder (for versions/markets where applicable) - 10.Front fog light button - 11.Hazard light switch - 12.Rear fog light button - 13.External lights con-
trol lever - 14.Instrument panel - 15.Windscreen wiper stalk - 16. Bonnet opening lever - 17.Set of controls - 18.Ignition key and ignition switch - 19.
Horn - 20.Steering wheel locking/release lever - 21.Driver’s air bag - 22.Door locking button - 23.Heating/ventilation/climate controls - 24.Cigar
lighter/ashtray housing lid - 25.Temperature sensor - 26.Glovebox.