2008 Acura TSX ignition

You can customize some vehicle
control settings f or ‘‘DRIVER 1’’ and
‘‘DRIVER 2’’ separately.
To have the driver’s ID detected,
make sure you use your transmitter
to unlock the driver’s door.
If you use the key to unlock the
driver’s door, the system cannot
recognize either ‘‘DRIVER 1’’ or
‘‘DRIVER 2.’’ In this case, when you
try to enter the customizing mode,‘‘DRIVER UNKNOWN
CUSTOMIZE IMPOSSIBLE’’ will be
displayed, and you cannot customize
some of the settings.
Refertothetableonpagetosee
what settings you can customize.
If you use your remote transmitter to
unlock the driver’s door, and the
system f ails to recognize either
‘‘DRIVER 1’’ or ‘‘DRIVER 2’’ see
page to link your transmitter to
your vehicle.
To use the system, your cell phone
and the HFL system must be linked.
Not all cell phones are compatible
with this system. Ref er to page
for instructions on how to link
your cell phone to the HFL and how
to receive or make phone calls, or
visit the acura.com/handsfreelink
website.
With the ignition switch in the ON
(II) position, press and hold the
INFO button for more than 3
seconds. ‘‘CUSTOMIZE ENTRY’’
appears on the multi-inf ormation
display. 219
88
132
Multi-Inf ormation Display
Customized Settings
86
DRIVER’S
ID
\f—\f—
y
y
(\fy\f\f
y
2008 TSX

While the multi-information display
shows ‘‘METER SETUP,’’ press the
SEL/RESET button on the steering
wheel. Press the INFO button until
you see ‘‘PRIMARY DISP
SELECTION’’ as shown above.
When you turn the ignition switch to
the ON (II) position, the primary
display of the trip computer always
shows ‘‘INST. MPG’’ (U.S. models)
or ‘‘INST. L/100 km’’ (Canadian
models) in def ault setting. You can
customize this setting to your liking
in f ollowing procedure.
Press the SEL/RESET button. The
display changes as shown above.
The lower segment changes f rom
‘‘INST. FUEL,’’ to ‘‘AVG. FUEL,’’ to
‘‘RANGE,’’ to ‘‘ELAPSED TIME,’’
then to ‘‘AVG. SPEED’’ each time
you press the INFO button. Enter
your selection by pressing the SEL/
RESET button.
Primary Display Select ion
Multi-Inf ormation Display
102
\f—\f—
y
\f\f
\fy
(\fy\f
\fy
2008 TSX

The headlights, parking lights,
taillights, and license plate lights
turn of f af ter the selected time when
you remove the key f rom the ignition
switch and close the driver’s door.If you f ail to enter your selection,
you will see the above display f or
several seconds, then the display
goes back to ‘‘CUSTOMIZE MENU.’’
Repeat the setup.To exit ‘‘HEADLIGHT AUTO OFF
TIMER,’’ press the INFO button
until you see ‘‘EXIT,’’ then press the
SEL/RESET button. The display
goes back to ‘‘CUSTOMIZE MENU.’’
Multi-Inf ormation Display
Inst rument s and Cont rols
109
\f—\f—
y
\f
\fy
(\fy\f

y
2008 TSX

µµPush down on the
lef t lever to signal a lef t turn and up
to signal a right turn. To signal a lane
change, push lightly on the lever in
the proper direction and hold it. The
lever will return to center when you
release it or complete a turn. Turning the switch
on the lef t lever to the
‘‘ ’’position turns on the parking
lights, taillights, instrument panel
lights, side-marker lights, and rear
license plate lights.
Turning the switch to the ‘‘ ’’
position turns on the headlights.
When the light switch is in the
‘‘ ’’ or the ‘‘ ’’ position, the
Lights On indicator comes on as a
reminder. This indicator stays on if
you leave the light switch on and
turn the ignition switch to the
ACCESSORY (I) or LOCK (0)
position.
If you leave the lights on with the
key removed f rom the ignition
switch, you will hear a reminder
chime when you open the driver’s
door.
Turn signal
Of f
Parking and indicator lights
Headlights
High beams
Flashhighbeams
Fog lights of f
Fog lights on
1.
2.
3.
4.
5.
6.
7.
8.
CONT INUED
Turn Signal
Headlights
Turn Signals and Headlights
Inst rument s and Cont rols
121
\f—\f—
y
\fy
(\fy\f
y
2008 TSX

µTo switch f rom low
beams to high beams, push the lef t
lever f orward until you hear a click.
The high beam indicator will come
on (see page ). Pull it back to
return to low beams. To flash the
high beams, pull the lever back
lightly, then release it. The high
beams will stay on as long as you
hold the lever back.
Turn the f og lights on and of f by
turning the switch next to the
headlight switch.
You can use the f og lights only when
the headlights are on low beam.
They will go of f when you turn the
headlights of f or onto high beam. This f eature turns of f the headlights,
parking lights, taillights, and license
plate lights within 15 seconds of
removing the key from the ignition
switch and closing the driver’s door.
You can change this 15 second timer
to 0, 30, or 60 seconds (see page
). With the headlight switch in the off
or position, the high beam
headlights and the high beam
indicator come on with reduced
brightness when you turn the
ignition switch to the ON (II)
position and release the parking
brake. They remain on until you turn
the ignition switch of f , even if you
set the parking brake.
This feature activates if you leave
the headlight switch in the or
position, remove the key, then
open and close the driver’s door.
If you remove the key f rom the
ignition switch with the headlight
switch on, but do not open the door,
the lights will turn of f af ter 10
minutes. The lights will turn on again when
you unlock or open the driver’s door.
If you unlock the door, but do not
open it within 15 seconds, the lights
will go off. With the driver’s door
open, you will hear a lights on
reminder chime.
66
108
Automatic Lighting Of f Feature
High Beams
Fog Lights (Canadian Models)
Daytime Running L ights
Headlights, Automatic Lighting Of f Feature, Daytime Running Lights
122
\f—\f—
y
\f\fy
(\fy\f
y
2008 TSX

Make sure the rear window is clear
and you have good visibility bef ore
starting to drive.
The rear window def ogger will clear
fog, frost, and thin ice from the
window. Push the def ogger button to
turn it on and of f . The indicator
above the button comes on to show
the def ogger is on. If you do not turn
it of f , the def ogger will shut itself of f
af ter about 35 minutes. It also shuts
of f when you turn of f the ignition
switch. You have to turn the
def ogger on again when you restart
the vehicle.
Push the button between the center
vents to turn on the hazard warning
lights (f our-way f lashers). This
causes all f our outside turn signal
lights and both turn signal indicators
in the instrument panel to flash. Use
the hazard warning lights if you need
to park in a dangerous area near
heavy traffic, or if your vehicle is
disabled.
The def ogger and antenna wires on
the inside of the rear window can be
accidentally damaged. When
cleaning the glass, always wipe side-
to-side.
Rear Window Def ogger
Hazard Warning Button
Hazard Warning Button, Rear Window Def ogger
124
Without navigation system With navigation system
\f—\f—
y
\fy
(\fy\f
y
2008 TSX

These keys contain electronic
circuits that are activated by the
immobilizer system. They will not
work to start the engine if the
circuits are damaged.Protect the keys f rom direct
sunlight, high temperature, and
high humidity. Donotdropthekeysorsetheavy
objects on them.
Keep the keys away f rom liquids.
If they get wet, dry them
immediately with a sof t cloth.
Youshouldhavereceivedakey
number tag with your keys. You will
need this key number if you ever
have to get a lost key replaced. Use
only Acura-approved key blanks.
The keys do not contain batteries.
Do not try to take them apart.
The master key fits all the locks on
your vehicle. The valet key works
only in the ignition and the door
locks. You can keep the trunk
release lever, rear seat trunk access,
and glove box locked when you leave
your vehicle and the valet key at a
parking f acility.
Keys and Locks
126
KEY
NUMBER
TAG MASTER
KEY
(Black)VALET KEY
(Light Gray)
\f—\f—
y
\fy
(\fy\f

y
2008 TSX

If the system repeatedly does not
recognize the coding of your key,
contact your dealer.
Do not attempt to alter this system
or add other devices to it. Electrical
problems could result that may make
your vehicle undrivable.
If you lose your key and you cannot
start the engine, contact your dealer.
The immobilizer system protects
your vehicle f rom thef t. If an
improperly-coded key (or other
device) is used, the engine will not
start.
When you turn the ignition switch to
the ON (II) position, the immobilizer
system indicator should come on f or
a f ew seconds, then go of f . If the
indicator starts to blink, it means the
system does not recognize the
coding of the key. Turn the ignition
switch to the LOCK (0) position,
remove the key, reinsert it, and turn
the ignition switch to the ON (II)
position again.
The system may not recognize your
key’s coding if another immobilizer
key or other metal object (i.e. key
f ob) is near the ignition switch when
you insert the key.As required by the FCC:
This device complies with Part 15 of theFCC rules. Operation is subject to thef ollowing two conditions: (1) This devicemay not cause harmf ul interf erence, and(2) this device must accept anyinterf erence received, includinginterf erence that may cause undesiredoperation.
Changes or modif ications not expresslyapproved by the party responsible f orcompliance could void the user’sauthority to operate the equipment.
This device complies with IndustryCanada Standard RSS-210.Operation is subject to the f ollowing twoconditions: (1) this device may not causeinterf erence, and (2) this device mustaccept any interf erence that may causeundesired operation of the device.
Immobilizer System
Inst rument s and Cont rols
127
Always take the ignition key with you
whenever you leave the vehicle alone.
\f—\f—
y
\fy
(\fy\f
y
2008 TSX