2008 Acura RL engine

When you are pressing the ignition
switch, or when the ignition switch is
in the ON (II) position, the beeper
sounds if you take the remote out of
the vehicle and close the door.
To remove the ignition switch cover,
insert the built-in key (see page ),
then pull the cover out by pulling the
built-in key while pushing it.
Also, if you close the door when the
ignition switch is not in the LOCK
(0) position and the remote is not
inside the vehicle, the keyless access
alarm sounds outside the vehicle, a
message appears on the multi-
inf ormation display, and the beeper
sounds if the ignition switch is in the
ON (II) position.
When the beeper sounds af ter you
close the driver’s door outside the
vehicle, check the position of the
ignition switch and the location of
the remote.
If the engine is running and you
removetheremotefromthevehicle,
it will continue to run. But once
turned to the LOCK (0) position, the
engine will not restart until a remote
is brought back into the vehicle.
177
K eyless A ccess System
Beeper and Message
Removing the Ignition Switch
Cover
K eyless Remot e Not Det ect ed
174
BUILT-IN KEY
IGNITION SWITCH COVER
pushpull
\f—\f—
y\f\f\f
y
(\fy\f
y
2008 RL

Thebatteriesintheremotenormally
lasts about 2 years. To ensure
maximum battery lif e, do not store
the remote close to electrical devices
such as computers or TVs. When the
multi-inf ormation display shows
‘‘KEYLESS REMOTE LOW
BATTERY,’’ replace the batteries as
soon as possible (see page ).
The engine does not restart if you
turn the ignition switch to the LOCK
(0) position when the remote is
outside the vehicle. Check where the
remote is. Make sure that you carry
the remote or built-in key with you
when you operate the ignition switch.
When the ignition switch is in the
ON (II) position, the multi-
inf ormation display shows
‘‘KEYLESS REMOTE NOT
DETECTED,’’ and the inside and
outside beepers sound.
The multi-inf ormation display
message goes away when you
bring the remote back inside the
vehicle, and close the door or
apply the parking brake.
The outside beeper sounds when
the ignition switch is in the
ACCESSORY (I) or the ON (II)
position.
If the engine is running and you
removetheremotefromthe
vehicle, it will continue to run.
Once turned to the LOCK (0)
position, the engine will not restart
until a remote is brought back into
the vehicle. If you pass the remote through an
open window, the system does not
respond.Also,evenwhentheremote
is inside the vehicle, the beeper may
sound when the location of the
remote is not detected due to
surrounding conditions. It is not a
f ailure. Make sure that you carry the
remote with you.
171
CONT INUED
K eyless A ccess System
K eyless Remot e L ow Bat t ery
Inst rument s and Cont rols
175
\f—\f—
y\f\f
\fy
(\fy\f
\fy
2008 RL

The indicator stays on while you
are driving.
The indicator comes on with the
ignition switch in the ON (II)
position.
The indicator comes on f or several
seconds when you turn the ignition
switch to the ON (II) position. Have
your vehicle checked by your dealer
if : The multi-inf ormation display
shows ‘‘CHECK KEYLESS
ACCESS SYSTEM.’’
In this case, use the built-in key to
lock/unlock the doors and start the
engine.
K eyless A ccess System
Check K eyless A ccess Syst em
176
KEYLESS ACCESS SYSTEM
INDICATOR
\f—\f—
y\f\f
y
(\fy\f

y
2008 RL

In the LO setting, the heater runs
continuously. It does not cycle with
temperature changes.
Follow these precautions whenever
you use the seat heaters:Use the HI setting only to heat the
seats quickly, because it draws
large amounts of current f rom the
battery.
If the engine is lef t idling f or an
extended period, do not use the
seat heaters, even on the LO
setting. It can weaken the battery,
causing hard starting.
Both f ront seats are equipped with
seat heaters. The passenger seat
only has heaters in the seat bottom
because of the side airbag cut of f
system. The ignition switch must be in the
ON (II) position to use the heaters.
Push the top of the switch, HI, to
rapidly heat up the seat. Af ter the
seat reaches a comfortable
temperature, select LO by pushing
the bottom of the switch. This will
keep the seat warm.
In the HI setting, the heater turns off
when the seat gets warm, and turns
back on after the seat’s temperature
drops.
If equipped
Seat Heaters
178
SEAT HEATER SWITCHES
Passenger’s
seat
Driver’s
seat
HEATERS
\f—\f—
y\f\fy
(\fy\f
y
2008 RL

ÝÛ
Û Ý
µ µ
µ µ Follow these precautions whenever
you use the seat heaters and the seat
ventilation:
Use the HI setting only to heat or
to ventilate the seats quickly,
because it draws large amounts of
current from the battery.
If the engine is lef t idling f or an
extended period, do not use the
seat heaters or the seat ventilation,
even on the LO setting. It can
weaken the battery, causing hard
starting.
When you press the button once,
the system is set to HI. To change to
the lower mode, press the button.
To turn the air ventilation off, press
the button until the indicators go
off.
To ventilate the seat, press the
button. The indicator (green) next to
the button will come on. The air
ventilation system has four settings:
HI Three indicators on.
MID Two indicators on.
LO One indicator on.
OFF All indicators of f .
Seat Heaters and Seat Ventilation (Canadian models)
180
\f—\f—
y\f\fy
(\fy\f
y
2008 RL

To apply the parking brake, push the
parking brake pedal down with your
f oot. To release the parking brake,
push on the pedal again. The parking
brake indicator on the instrument
panel should go out when the
parking brake is f ully released with
the engine running (see page ).63
Parking Brake
Inst rument s and Cont rols
187
PARKING BRAKE PEDAL
Driving the vehicle with the parking
brake applied can damage the rear
brakes, axles, and tires. A beeper will
sound if the vehicle is put into gear
with the parking brake on.
\f—\f—
y\f
\fy
(\fy\f
y
2008 RL

The heater uses engine coolant to
warm the air. If the engine is cold, it
will be several minutes bef ore you
f eel warm air coming f rom the
system.
The f low-through ventilation system
draws in outside air, circulates it
through the interior, then exhausts it
through vents near the rear window. Set the temperature to the lower
limit.
Make sure the A/C is of f .
Select and fresh air mode.
Set the f an to the desired speed. Press the A/C button to view
the climate control display.
Turn on the A/C by pushing
ENTER on the interf ace selector.
You will see A/C ON in the display.
Make sure the temperature is set
to maximum cool.
Push the interf ace selector down,
then select by turning the
interf ace knob.
If the outside air is humid, select
recirculation mode. If the outside
air is dry, select f resh air mode.
Push the interf ace selector down,
then set the f an to the desired
speed by turning the interf ace
knob.
Press the A/C button to view
theclimatecontroldisplay.
Turn the interface knob to set the
fantothedesiredspeed.
Push the interf ace selector down,
then select and f resh air
mode.
Adjust the warmth of the air with
the temperature control bars.
You can set the temperature for the
driver’s side and the passenger’s side
separately when this button is
pressed (indicator on). When the
indicator in the DUAL button is off,
you can adjust both sides to the
same temperature with the driver’s
side temperature control bar.
Air conditioning places an extra load
on the engine. Watch the engine
coolant temperature gauge (see page). If it moves near the red zone,
turn of f the A/C until the gauge
reading returns to normal. you can
cool it down more rapidly by partially
opening the windows, turning on the
air conditioning, and setting the fan
to maximum speed in f resh air mode.
1.
2.
3.
4. 1.
2.
3.
4.
5.
6.
1.
2.
3.
4.
70
If the interior is very warm,
Using the Heater
Dual Button
Ventilation
Using the A/C
Climate Control System
Features
203
\f—\f—
y\f
y
(\fy\f\fy
2008 RL

CONT INUED
If within ten minutes the system fails
to locate a suf f icient number of
satellites to locate your position, the
screen above appears. Follow the
instructions on the screen.You have acquired a device
(‘‘DEVICE’’) that includes sof tware
licensed by ALPINE ELECTRONICS,
INC., f rom an af f iliate of Microsof t
Corporation (collectively ‘‘MS’’).
Those installed software products of
MSorigin,aswellasassociated
media, printed materials, and
‘‘online’’ or electronic documentation
(‘‘SOFTWARE’’) are protected by
international intellectual property
laws and treaties. The SOFTWARE
is licensed, not sold. All rights
reserved.
After 30 minutes with this screen
displayed, turn of f the engine and
restart the vehicle. If you now see
the , the GPS
initialization is complete.
The average acquiring time is less
than 10 minutes, but it can take as
long as 45 minutes.
If the system is still unable to
acquire a signal, f ollow the
instructions on the screen, or
contact your local dealer for
assistance. License notice
Disclaimer screen
Compass System (U.S. model without navigation system)
Features
261
NOTE:
\f—\f—
y\fy
(\fy\fy
2008 RL