2008 Acura RL lock

ÛÝÛÝ
With the multi-information display
and the INFO ( / ) and SEL/
RESET buttons on the right side of
the steering wheel, you can
customize some vehicle control
settings f or ‘‘DRIVER 1’’ or
‘‘DRIVER 2’’. If ‘‘DRIVER 1’’ or
‘‘DRIVER 2’’ is not displayed,
customizing is not possible.
To have the driver’s ID detected,
make sure your remote is linked to
the system (see
on page ). Then use your
remote to unlock the doors (see on page
). To enter the customizing mode,
press and hold the INFO ( / )
button for more than 3 seconds while
the multi-information display is in its
normal mode.
If you turn the ignition switch to the
ACCESSORY (I) or the LOCK (0)
position, or move the shif t lever out
of Park, the display will change to
the normal screen.
When the multi-information
display does not show the driver’s
ID. The f irst customizing menu is:
CHG SETTING (see page )
If you disconnect the battery, and
then do not unlock the door.
When the keyless memory
settings are of f (see page ). DEFAULT ALL (see page )
You cannot customize the settings
under these conditions:
To change the settings, the ignition
switch must be in the ON (II)
position, and the vehicle must be
stopped with the transmission in
Park. Ref er to the f ollowing table f or a
brief summary of each customizable
setting and its default. For more
inf ormation, ref er to the page
number ref erences in the table.
104
108 170
87
85
CONT INUED
Customized Settings
Memory Position
Link
K eyless A ccess Setup
Multi-Inf ormation Display
Inst rument s and Cont rols
81
\f—\f—
y\f
y
(\fy\f\fy
2008 RL

Î
Î
Î
Î
Î
Î Î
Î DOOR UNLOCK MODE
KEYLESS ACCESS LIGHT
FLASH
KEYLESS ACCESS BEEP
INTERIOR LIGHT
DIMMING T IME
HEADLIGHT AUT O OFF
TIMER
AUTO LIGHT
SENSITIVITY
AUTO DOOR LOCK
CUST OMIZE MENU
DRIVER DOOR
ALL DOORS
ON
OFF
ON
OFF
60 SEC
30 SEC
15 SEC
60 SEC
30 SEC
15 SEC
MAX
HIGH
MID
LOW
SHIFT FROM P
WITH VEH SPD
OFF
KEYLESS ACCESS
SETUP
(see page108)
LIGHTING SETUP
(see page115)
DOOR/WINDOW
SETUP
(see page122) Page
109
111
113
116
118
120
123
CHG SETTING
(see page87)
Description
Changes which doors unlock when
you use the remote or grab the
driver’s doorhandle.
Causes some exterior lights to
blinktwicewhenyouunlockthe
doors by grabbing the driver’s
door handle.
Cause the beeper to sound twice
when you unlock the doors by
grabbing the driver’s door handle.
Changes how long (in seconds)
the interior lights stay on after you
close the doors.
Changes how long (in seconds)
the exterior lights stay on after
you close the driver’s door.
Changes the light level that causes
theheadlightstocomeon.The
headlight switch needs to be in the
AUTO position.
Changes when the doors
automatically lock.
: Default setting 0SEC
MIN
CONT INUED
CUSTOMIZE SET UPCUST OMIZE GROUP
CUSTOMIZE ENTRY
Multi-Inf ormation Display
Inst rument s and Cont rols
83
——
yy
(yy
2008 RL

ÎÎ
Î
Î Î
Î CUST OMIZE MENU
DOOR/WINDOW
SETUP
(see page122)
WIPER SETUP
(see page133) AUTO DOOR UNLOCK
DOOR LOCK MODE
KEYLESS LOCK
ACKNOWLEDGMENT
SECURITY RELOCK
TIMER
WIPER ACTION
SHIFT TO P
IGN OFF
OFF
DRIVER DOOR
ALL DOORS
ON
OFF
90 SEC
60 SEC
30 SEC
INTERMITTENT
WITH VEH SPD
SETPage
125
127
129
131
134
85
CHG SETTING
(see page87)
DEFAULT ALL
(see page85) Description
Changes when the doors
automatically unlock.
Changes which doors unlock with the
f irst push of the remote’s unlock
button.
The exterior lights flash each time
you press the LOCK or UNLOCK
button.
Changes how long it takes (in
seconds) f or the doors to relock and
the security system to set after you
unlock the driver’s door without
opening it.
Changes the wiper operation among
two settings when the wiper switch is
in the INT position.
Changes all settings to the default.
: Default setting
CUST OMIZE GROUP
CANCEL
CUSTOMIZE ENTRYCUSTOMIZE SET UP
Multi-Inf ormation Display
84
——
yy
(yy
2008 RL

ÛÝ
µ
µ
µ
ÛÝ
While METER SETUP is shown in
the CUSTOMIZE GROUP of the
multi-inf ormation display, press the
SEL/RESET button. The screen
changes to CUSTOMIZE MENU.
Press the INFO ( / ) button until
you see the above display.
IGN OFF The elapsed time is
reset when you turn the ignition
switch to the LOCK (0) position.
TRIP A The elapsed time is reset
when the Trip A is reset.
TRIP B The elapsed time is reset
when the Trip B is reset.
Press the SEL/RESET button. The
screen changes as shown above.
Select the desired setting by
pressing the INFO ( / ) button,
then press the SEL/RESET button
to enter your selection.
There are three elapsed time reset
choices you can make:
CONT INUED
Elapsed T ime Reset
Multi-Inf ormation Display
Inst rument s and Cont rols
101
\f—\f—
y\f\fy
(\fy\f
\fy
2008 RL

ÛÝÛÝ
When AUTO TILT & TELESCOPIC
is set to ON, the steering wheel
automatically moves f ully in and up
when you turn the ignition switch to
the LOCK (0) position and release it,
or when you remove the built-in key
from the ignition switch.
While the multi-information display
is in the POSITION SETUP screen
of the CUSTOMIZE GROUP, press
the SEL/RESET button. The screen
changes to CUSTOMIZE MENU.
Press the INFO ( / ) button until
you see the above display.Press the SEL/RESET button. The
screen changes as shown above.
Select ON or OFF by pressing the
INFO ( / ) button, then press the
SEL/RESET button to enter your
selection.
A ut o T ilt & T elescopic
Multi-Inf ormation Display
106
\f—\f—
y\fy
(\fy\f


y
2008 RL

Û
Ý
ÛÝ Û
Ý
ÛÝ
DOOR UNLOCK MODE
KEYLESS ACCESS
LIGHT FLASH
KEYLESS ACCESS BEEP
Each time you press the INFO ( / ) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button, until you see
the setting you want to customize,
then press the SEL/RESET button
to enter your selection.
There are three settings in the
keyless access setup:
While the multi-information display
is in the CUSTOMIZE GROUP
screen, select KEYLESS ACCESS
SETUP by pressing the INFO ( / ) button, then press the SEL/
RESET button.
K EYL ESS A CCESS Setup
Multi-Inf ormation Display
108
Press the or button.
Press the SEL/RESET button. seepage109
seepage111
seepage113
\f—\f—
y\f\fy
(\fy\f

y
2008 RL

ÛÝ
To select whether the driver’s door
or all doors unlock when you open
the driver’s door with the remote or
by grabbing the door handle (while
carrying the remote), f ollow these
instructions:
While the multi-information display
is in the KEYLESS ACCESS SETUP
screen of the CUSTOMIZE GROUP,
press the SEL/RESET button. The
screen changes to the above display.Press the SEL/RESET button. The
screen changes as shown above.
Select DRIVER DOOR ONLY or
ALL DOORS by pressing the INFO
( / ) button, then press the SEL/
RESET button to enter your
selection.
CONT INUED
Door Unlock Mode
Multi-Inf ormation Display
Inst rument s and Cont rols
109
\f—\f—
y\f

y
(\fy\f

y
2008 RL

ÛÝ
To exit DOOR UNLOCK MODE
without changing the current setting,
select EXIT by pressing the INFO
( / ) button, then press the SEL/
RESET button. The screen goes
back to CUSTOMIZE MENU.
When your choice is set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE ENTRY.
If your choice is not set, you will see
the above display f or several seconds,
then the screen goes back to
CUSTOMIZE SETUP. If this
happens, you need to repeat the door
unlock mode setup.
Multi-Inf ormation Display
110
\f—\f—
y\f
y
(\fy\f

y
2008 RL