2008 Acura RL dead battery

Your vehicle’s audio system may
disable itself if it is disconnected
f rom electrical power f or any reason.
To make it work again, you must
enter a specif ic f ive-digit code with
the preset buttons. Because there
are hundreds of number
combinations possible f rom the f ive
digits, making the system work
without knowing the exact code is
nearly impossible.
If you lose the card, you must obtain
the code number f rom your dealer.
To do this, you will need the audio
system’s serial number.If your vehicle’s battery is discon-
nected or goes dead, or the radio
f use is removed, the audio system
will disable itself . If this happens,
youwillsee‘‘ ’’intheupper
display the next time you turn on the
system. Use the preset buttons to
enter the code. The code is located
on the radio code card included in
your owner’s manual kit. When it is
entered correctly, the radio will start
playing.
If you make a mistake entering the
code, do not start over; complete the
f ive-digit sequence, then enter the
correct code. You have 10 tries to
enter the correct code.
If thecodecardislost,yourdealer
can access your code with your
radio’s serial number. To access the
serial number, turn the radio on. It
must display ‘‘ ’’, then turn
the radio off. Push and hold the
preset 1 and preset 6 buttons, thenpush the power/volume knob. The
serial number will appear in two sets
of f our digits.
The system will retain your AM and
FM presets even if power is
disconnected.
You should have received a radio
code card that lists your audio
system’s code and serial numbers. It
is best to store this card in a saf e
place at home. In addition, you
should write the audio system’s
serial number in this owner’s manual.
Radio T hef t Protection
Features
241
\f—\f—
y\f\f\fy
(\fy\fy
2008 RL

CONT INUED
Enter the f our-digit compass system
security code. If you have entered it
correctly, the display changes to the. You have ten
chances to enter the correct code. If
all ten are incorrect, turn the ignition
to OFF, then back to ON (II) to have
ten more chances to enter the
correct code.
When you purchased the vehicle,
you should have received two cards
that have the audio and compass
system’s security codes and serial
numbers. Keep these cards in a saf e place in case you need the codes. If
you lose the cards, you must obtain
the security codes f rom your dealer.
If the battery goes dead or is
disconnected f or any reason, you will
have to enter a security code into
both the audio system and the
compass system bef ore you can use
it again. To enter the code, turn the interf ace
knob to select the number, then
press the interf ace selector to enter
it. Keep doing the same procedure to
enter all f our correct numbers. If you
need to delete the number you
entered mistakenly, move the
interface selector to the right.
If f or any reason, you lose power to
the compass system (the battery was
disconnected), the system needs to
be initialized bef ore you can use it.
Initialization requires this:
Entry of the compass system 4-
digit security code to ‘‘unlock’’ the
system.
GPS initialization. This may not be
needed depending on how long the
system was without power. Disclaimer screen
System Initialization
Entering the Security Code
Compass System (U.S. model without navigation system)
Features
259
\f—\f—
y\f\fy
(\fy\fy
2008 RL

µµµ µ
µ
µ
Do this:
Press the brake pedal, then
move the shift lever.
Move the lever.
To shift from:
PtoR
RtoN
NtoD
DtoD
DtoD DtoNNtoR RtoP
3
3
To avoid transmission damage, come
to a complete stop bef ore shif ting
into Park. The shif t lever must be in
Park bef ore you can turn the ignition
switch to the LOCK (0) position, or
remove the built-in key from the
ignition switch. Press the brake
pedal to shif t f rom Park to reverse.
To shif t f rom neutral to reverse,
come to a complete stop and then
shif t.
Your vehicle has a reverse lockout so
you cannot accidentally shif t to
reverse f rom neutral or any other
driving position when the vehicle
speed exceeds 5 6 mph (8 10
km/h).
If you cannot shif t to reverse when
the vehicle is stopped, press the
brake pedal, slowly shif t to neutral,
andthenshifttoreverse. If there is a problem in the reverse
lockout system, or your vehicle’s
battery is disconnected or goes dead,
you cannot shif t to reverse. (Ref er to
on page ).
Use neutral if you
need to restart a stalled engine, or if
it is necessary to stop brief ly with
the engine idling. Shif t to the Park
position if you need to leave your
vehicle for any reason. Press on the
brake pedal when you are moving
the shift lever from neutral to
another gear.
Use this position f or
your normal driving. The
transmission automatically selects a
suitable gear (1 through 5) f or your
speed and acceleration. You may
notice the transmission shif ting up at
higher engine speeds when the
engine is cold. This helps the engine
warm up f aster.
If you have done all of the above and
still cannot move the lever out of
Park, see on
page . This position mechani-
cally locks the transmission. Use
Park whenever you are turning of f or
starting the engine. To shif t out of
Park, you must press on the brake
pedal and have your f oot of f the
accelerator pedal. Move the shif t
levertotherighttoshiftoutof Park.
354 354
Automatic Transmission
Reverse (R)
Shif t L ock Release
Neutral (N)
Drive (D)
Shif t L ock Release
Park (P)
350
\f—\f—
y\f\fy
(\fy\fy
2008 RL

If your vehicle’s battery is
disconnected or goes dead, all stored
driving positions will be lost. To
store the driving positions again, see
the storing procedure on page .
The navigation system will also
disableitself.Thenexttimeyouturn
on the ignition switch, the system
will require you to enter a PIN
bef ore it can be used. Ref er to the
navigation system manual.Turn the knob of the battery cover
toUNLOCKasshowninthe
illustration.
If your vehicle’s battery is
disconnected or goes dead, the audio
system may disable itself . The next
timeyouturnontheradioyouwill
see ‘‘ ’’ in the f requency
display. Use the preset buttons to
enter the code (see page ).
The compass System will also
disableitself.Thenexttimeyouturn
on the ignition switch, the system
will require you to enter a PIN
bef ore it can be used. Enter the f our-
digit anti-thef t security code (see
page ). You will also need reset
the clock according to the
instruction of setting the clock (see
page ). If your vehicle’s battery is
disconnected or goes dead, the
power tilt and telescopic steering
wheel system will be disabled. The
system needs to be reset af ter
reconnecting the battery (see page
). 1.
160
259 274 241
148
On vehicles with navigation system
On vehicles without navigation system
Checking the Battery
Removing the Battery Cover
428
KNOB TABUNLOCK
LOCK
\f—\f—
y\fy
(\fy\fy
2008 RL

Your vehicle has certain ‘‘readiness
codes’’ that are part of the on-board
diagnostics f or the emissions
systems. In some states, part of the
emissions testing is to make sure
these codes are set. If they are not
set, the test cannot be completed.
If this indicator comes on
while driving, or if you see
a ‘‘CHECK EMISSION
SYSTEM’’ message on the multi-
inf ormation display, it means one of
the engine’s emissions control
systems may have a problem. Even
though you may f eel no dif f erence in
your vehicle’s perf ormance, it can
reduce your f uel economy and cause
increased emissions. Continued
operation may cause serious damage. If the indicator comes on repeatedly,
even though it may go of f as you
continue driving, have the vehicle
checked by your dealer as soon as
possible.
If you have recently ref ueled your
vehicle, the indicator coming on
could be due to a loose or missing
f uel f ill cap. You will also see a
‘‘TIGHTEN FUEL CAP’’ message on
the multi-information display.
Tighten the cap until it clicks at least
once (see page ). Tightening the
cap will not turn the indicator of f
immediately; it can take several days
of normal driving. If the battery in your vehicle has
been disconnected or gone dead,
thesecodesmaybeerased.Itcan
take several days of driving under
various conditions to set the codes
again.
To check if they are set, turn the
ignition switch to the ON (II)
position, without starting the engine.
The malf unction indicator lamp will
come on f or 20 seconds. If it then
goes of f , the readiness codes are set.
If it blinks f ive times, the readiness
codes are not set. If possible, do not
take your vehicle f or an emissions
test until the readiness codes are set.
Refer to for
more information (see page ).
475
331 Readiness Code
Emissions T esting
Malf unction Indicator L amp
448
If you keep driving with the
malf unction indicator lamp on, you can
damage your vehicle’s emissions
controls and engine. Those repairs may
not be covered by your vehicle’s
warranties.
\f—\f—
y\fy
(\fy\fy
2008 RL

If you take your vehicle f or an
emissions test shortly af ter the
battery has been disconnected or
gone dead, it may not pass the test.
This is because of certain ‘‘readiness
codes’’ that must be set in the on-
board diagnostics f or the emissions
systems. These codes are erased
when the battery is disconnected,
and set again only after several days
of driving under a variety of
conditions.If the testing f acility determines that
the readiness codes are not set, you
will be requested to return at a later
date to complete the test. If you must
get the vehicle retested within the
next two or three days, you can
condition the vehicle f or retesting by
doing the f ollowing.
Make sure the gas tank is nearly,
but not completely, f ull (around
3/4). Without touching the accelerator
pedal, start the engine, and let it
idle f or 20 seconds.
Keep the vehicle in Park. Increase
the engine speed to 2,000 rpm, and
hold it there until the temperature
gauge rises to at least 1/4 of the
scale (about 3 minutes).
Make sure the vehicle has been
parked with the engine of f f or 6
hours or more.
Make sure the ambient
temperature is between 40° and
95°F. Without touching the accelerator
pedal and let the engine idle f or 20
seconds.
1.
2.
3. 4.
5.
6.
CONT INUED
T esting of Readiness Codes
Emissions T esting
Technical Inf ormation
475
\f—\f—
y
\f\fy
(\fy\f\fy
2008 RL

Î
CONT INUED
..............................
Economy, Fuel .334
..................................
Emergencies .431
.............
Battery, Jump Starting .441
...........
Brake System Indicator .449
................
Changing a Flat Tire .436
.....
Charging System Indicator .447
..................
Checking the Fuses .453 .......
Hazard Warning Flashers .145
............................
Jump Starting .441
.....
Low Oil Pressure Indicator .447
...
Malf unction Indicator Lamp .448
Opening the Fuel Fill Door
................................
Manually .450
..................
Overheated Engine .444
.......................................
Towing .459
.........................
Emergency Brake .187
....................
Emergency Flashers .145
......................
Emergency Towing .459
..........
Emergency Trunk Opener .154
.......................
Emissions Controls .472
........................
Emissions Testing .475
...............
DANGER, Explanation of .iii
...................................
Dashboard .4,60
..............
Daytime Running Lights .142
.......................................
Indicator .65
.................................
Dead Battery .440
............
Def ects, Reporting Saf ety .480
..............
Def ogger, Rear Window .146
..............
Def rosting the Windows .204
..........................
Dif f erential Fluid .464
....................................
Dimensions .464
.............
Dimming the Headlights .140
Dipstick
..........
Automatic Transmission .404
..................................
Engine Oil .333 ........................
Directional Signals .140
........
Disc Brake Wear Indicators .358
.....................
Disposal of Used Oil .401
Doors
............
Locking and Unlocking .152
..................
Lockout Prevention .152
.................
Monitor Indicator .13,79
....................
Power Door Locks .152
........
DOT Tire Quality Grading .466
...........
Driver and Passenger Safety .7
.......................................
Driver’s ID .81
...........................................
Driving .345
....................................
Economy .336
Driving Position Memory ........................................
System .160
..................
Dust and Pollen Filter .415
.........................
Customize Settings .81
...................................
ACC Setup .89
................
Door/Window Setup .122
.......
KEYLESS ACCESS Setup .108
...........................
Lighting Setup .115
.................................
Meter Setup .94
...........................
Position Setup .103
........................
Setting to Def ault .85
...............................
Wiper Setup .133
Index
E
D
INDEX
III
——
y
y
(yy
2008 RL

Î
Î
ÎÎ Î................................
Saf ety Belts .10,21
.........
Safety Defects, Reporting .480
.................................
Saf ety Features .9
.........................................
Airbags .11
.....................................
Seat Belts .10
.............
Saf ety Labels, Location of .57
..............................
Saf ety Messages . iii
.................
Satellite Digital Radio .217
...................................
Seat Belts .10,21
...............
Additional Information .21
Automatic Seat Belt
...............................
Tensioners .23
.....................................
Cleaning .415
.............................
e-pretensioner .24
................
Lap/Shoulder Belt .17,22
................................
Maintenance .25
Reminder Indicator and
................................
Beeper .21,62
...................
System Components .21
...............
Use During Pregnancy .19
..................................
Seat Heaters .178
..................
Seat Position Memory .160
.........................
Seat Ventilation .179
......................
Seats, Adjusting the .155 ............................
Security System .276
.....
Sequential Sports Shif t Mode .351
..........................
Paddle Shif ters .351
...............................
Serial Number .462
...........................
Service Intervals .387
......
Service Manual, Purchasing .481
.........
Service Station Procedures .329
Super Handling-All Wheel Drive
.............................
(SH-AWD) .356
..
Torque Distribution Monitor .356
.......................................
Indicator .66
...
Shif t Lever Position Indicators .349
........................
Shif t Lock Release .354
..............................
Side Airbags .11,32
How the Side Airbag of f ......................
Indicator Works .35
...
How Your Side Airbags Work .32
................
Side Curtain Airbags .11,34
How Your Side Curtain ..........................
Airbags Work .34
Side Marker Lights, Bulb .........................
Replacement in .411
.............................
Signaling Turns .140
.....................................
Snow Tires .424
................................
Sound System .207 Spare Tire
......................................
Inf lating .435
............................
Specif ications .465
.....................
Specif ication Charts .464
................................
Speed Limiter .354
.......................................
Spotlights .196
..........
SRS, Additional Inf ormation .26
...
Additional Safety Precautions .37
..
How the SRS Indicator Works .34
How Your Airbags
............................
Work .29,32,34
........................
SRS Components .26
..................................
SRS Service .36
.............................
SRS Indicator .34,63
START (Ignition Switch
.....................................
Position) .151
.......................
Starting the Engine .347
...................
Auto Control Mode .347
In Cold Weather at High
..................................
Altitude .347
................
With a Dead Battery .441
........
Steam Coming f rom Engine .444
Steering Wheel
..............................
Adjustments .147
...........
Anti-thef t Column Lock .151
......................
Position Memory .160
Index
S
VIII
——
y

y
(yy
2008 RL