2008 Acura RL clock

To adjust the minute, turn the
interface knob to the right to display
the adjustment screen f or MINUTE.Press the center of the interf ace
selector to enter the time. The
screen will return to the
screen (see page ).
Turn the interface knob to adjust the
minute.
To adjust the hour, turn the interface
knob, then press the center of the
interf ace selector.
274
Clock
adjustment
Compass System (U.S. model without navigation system)
Features
275
\f—\f—
y\fy
(\fy\f\fy
2008 RL

The coolant level should be up to
the base of the f iller neck. Add
coolant if it is low.
When the radiator and engine are
cool, relieve any pressure in the
cooling system by turning the
radiator cap counterclockwise,
without pressing down.
Remove the radiator cap by
pushing down and turning
counterclockwise. Put the radiator cap back on, and
tighten it fully.
Pour coolant into the reserve tank.
Fill it to half way between the MAX
and MIN marks. Put the cap back
on the reserve tank.
Do not add any rust inhibitors or
other additives to your vehicle’s
cooling system. They may not be
compatible with the coolant or
engine components.
Pourthecoolantslowlyandcarefully
so you do not spill any. Clean up any
spill immediately; it could damage
components in the engine
compartment.
3.
1.
2. 4.
5.
Engine Coolant
Maint enance
403
RADIATOR CAP
RESERVE TANK
\f—\f—
y\fy
(\fy\f\fy
2008 RL

CONT INUED
Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb by turning it one-
quarter turn counterclockwise.
Remove the left or right side
engine compartment cover f rom
thesideyouareworkingonby
caref ully pulling the cover out (see
page ).
If youarereplacingthebulbon
the driver’s side, remove the
battery cover (see page ), then
remove the battery hold-down by
removing the two nuts with a 10
mm wrench. Then caref ully slide
the battery toward the engine to
access the bulb.2.
3.
1.
398
428
Lights
Maint enance
409
NUTSBULB
BATTERY HOLD-DOWN CONNECTOR
\f—\f—
y\f\fy
(\fy\f
y
2008 RL

Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Turn on the headlights to test the
new bulb.
(Driver’s side)
Reinstall the engine compartment
side cover.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Push the bulb in slightly, and turn
it counterclockwise.
Reinstall the battery in the reverse
order of removal, and reinstall the
cover on the battery. Remove the left or right side
engine compartment cover f rom
thesideyouareworkingonby
caref ully pulling the cover out (see
page ).
If you are replacing a driver’s side
bulb, slide the battery toward the
engine to get more clearance (see
page ).
2.
1.
4.
5.
6.
7.
8.
3.
398
428
Lights
Replacing a Front T urn Signal/
FrontParkingLightBulb
410
SOCKET
BULB
\f—\f—
y\f
\f\fy
(\fy\f
y
2008 RL

CONT INUED
If you are replacing a driver’s side
bulb, slide the battery toward the
engine to get more clearance (see
page ).
Use a f lat-tipped screwdriver to
remove the holding clip f rom the
windshield washer reservoir.
(Passenger’s side)
Remove the left or right side
engine compartment cover (see
page ).
Pull the bulb straight out of its
socket. Install the new bulb into the
socket.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the lights to make sure
the new bulb is working.
(Driver’s side)
Reinstall the battery and the
battery cover.
Reinstall the engine compartment
side cover.
1.
2.
5.
6.
7.
8.
4.
398
428
On model without adaptive f ront lighting system
Lights
Replacing a Front Position/Side
Marker L ight Bulb
Maint enance
411
SOCKET
BULB
\f—\f—
y\f

y
(\fy\f
y
2008 RL

Your vehicle uses halogen light
bulbs. When replacing a bulb, handle
it by its plastic case, and protect the
glass from contact with your skin or
hard objects. If you touch the glass,
clean it with denatured alcohol and a
clean cloth.
Install the new bulb into the
socket.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Turn on the lights to make sure
the new bulb is working.
(Driver’s side)
Reinstall the battery and the
battery cover.
(Passenger’s side)
Reinstall the windshield washer
reservoir.
Reinstall the engine compartment
side cover.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. 5.
6.
7.
8.
9.
3.
4.
Lights
ReplacingaFogLightBulb
412
SOCKET
HOLDING CLIP
BULB
Halogen bulbs get very hot when lit. Oil,
perspiration, or a scratch on the glass
can cause the bulb to overheat and
shatter.
\f—\f—
y\f
y
(\fy\f
y
2008 RL

Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Turn on the f og lights to test the
new bulb.
Reinstall the two undercover bolts
onthesideundercoverand
tighten them securely. Put the
holding clip back on the side
under cover and push on the
center until it locks (the center is
flushwiththehead).
Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb by turning it one-
quarter turn counterclockwise.
Caref ully push up the side under
cover into the bumper.
Use a Phillips-head screwdriver to
remove the two undercover bolts,
and remove the holding clip with a
f lat-tipped screwdriver. 3.
4. 5.
6.
8.
7.
1.
2.
Lights
Maint enance
413
CLIP CONNECTORBULB
BOLTS
\f—\f—
y\f
y
(\fy\f
y
2008 RL

Determine which of the two bulbs
is burned out: turn signal or back-
up light.
Remove the socket by turning it
one-quarter turn counterclockwise.
Remove the burned out bulb by
pulling it straight out of its socket.
Open the trunk lid, and remove
the lef t or right maintenance lid.
Remove the mounting nut with an
8mmwrench.
Carefully pry in the top or bottom
edge of the trim with a small f lat-
tipped screwdriver, and pull the
trim straight back.
Remove the two mounting bolts
with an 8 mm wrench.
Pull the taillight assembly straight
back out of the body.
2.
1. 3.
4.
5.6.
7.
8.
Lights
Replacing Rear Bulbs
414
MOUNTING NUT
MAINTENANCE LID BOLTS
BULBS
TAIL LIGHT TRIM SOCKETS
\f—\f—
y\f
\fy
(\fy\f
y
2008 RL