2008 Acura MDX bulb

This indicator normally comes on f or
a f ew seconds when you turn the
ignition switch to the ON (II)
position.
If itcomesonandstaysonatany
other time, or it does not come on
when you turn the ignition switch to
the ON (II) position, there is a
problem with the VSA system. You
will also see a ‘‘CHECK VSA
SYSTEM’’ message on the multi-
inf ormation display (see page ).
Take your vehicle to a dealer to have
it checked. Without VSA, your
vehicle still has normal driving ability,
but will not have VSA traction and
stability enhancement. For more
inf ormation, see page .
This indicator may also come on if
there is a problem with the trailer
stability assist f unction (see page). This indicator normally comes on f or
a f ew seconds when you turn the
ignition switch to the ON (II)
position. For more inf ormation, see
page .
This indicator has f our f unctions.
Itcomesonasareminderthatyou
have turned off the vehicle
stability assist (VSA) system.
It flashes when VSA is active (see
page ).
It f lashes when trailer stability
assist is activating (see page ).
It comes on along with the VSA
system indicator if there is a
problem with the VSA system.
You will also see a ‘‘CHECK VSA
SYSTEM’’ message and a
‘‘CHECK TRAILER STABILITY
ASSIST’’ message on the multi- inf ormation display (see page ).
The lef t or right turn signal indicator
blinks when you signal a lane change
or turn. If an indicator does not blink
or blinks rapidly, it usually means
one of the turn signal bulbs is
burned out (see page ). Replace
the bulb as soon as possible, since
other drivers cannot see that you are
signaling.
When you press the hazard warning
button, both turn signal indicators
and all turn signals on the outside of
the vehicle f lash.
1.
2.
3.
4.
81 81
359
375 359
359 375 404
Instrument Panel Indicators
Vehicle Stability Assist
(VSA ) System Indicator
VSA A ctivation Indicator
Turn Signal and
Hazard Warning
Indicators
Inst rument s and Cont rols
67
——yy
()-
yy
2008 MDX

CONT INUED
Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb by turning it
about one-quarter turn
counterclockwise.
Remove the f ront bulkhead cover
(see page ).
Open the hood.
Your vehicle has halogen headlight
bulbs. When replacing a bulb, handle
it by its base, and protect the glass
f rom contact with your skin or hard
objects. If you touch the glass, clean
it with denatured alcohol and a clean
cloth.
The low beam headlight bulbs are a
type of high voltage discharge tube.
High voltage can remain in the
circuit even with the light switch of f
and the key removed. Because of
this, you should not attempt to
examine or change a low beam
headlight bulb yourself . If a low
beam headlight bulb fails, take the
vehicle to your dealer to have it
replaced.
Theheadlightswereproperlyaimed
when your vehicle was new. If you
regularly carry heavy items in the
trunk or pull a trailer, readjustment
may be required. Adjustments
should be done by your dealer or
other qualif ied technician.
1.
2.3.
4.
392
MDX and Technology Packages models
Headlight A iming Replacing a High Beam Headlight Bulb
L ow Beam Headlight Bulb
Replacement
Lights
Maint enance
403
BULB
CONNECTOR
Halogen headlight bulbs get very hot
when lit. Oil, perspiration, or a scratch
on the glass can cause the bulb to
overheat and shatter.
\f—\f—\fy
\f
\f\fy
()-
\fy\f\fy
2008 MDX

Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector onto
the new bulb.
Turn on the headlights to test the
new bulb.
Push the new bulb straight into
the socket until it bottoms.
Turn on the lights to make sure
the new bulb is working.
Open the hood.
Pull the bulb straight out of its
socket.
Remove the socket by turning it
one-quarter turn counterclockwise.
Remove the f ront bulkhead cover
(see page ).
1.
2.
3.
4. 5.
5.
6.
7.
6.
7.
392
Replacing Front Turn Signal/
Parking and Side Marker Light
Bulbs
Lights
404
BULB
BULB
SOCKET
FRONT TURN SIGNAL LIGHT
PARKING LIGHT
SOCKET
\f—\f—\fy
\f


y
()-
\fy\f\fy
2008 MDX

CONT INUED
Remove the bolt and use the f lat-
tip screwdriver to remove the
holding clips located under the
f ront bumper.
Push down the inner f ender.
Your vehicle uses halogen light
bulbs. When replacing a bulb, handle
it by its plastic case, and protect the
glass from contact with your skin or
hard objects. If you touch the glass,
clean it with denatured alcohol and a
clean cloth.
1.
2.
Lights
Replacing Front Fog/Daytime
Running L ight Bulbs
Maint enance
405
SIDE MARKER LIGHT BOLT
HOLDING
CLIPS
BULB
SOCKET
Halogen bulbs get very hot when lit.
Oil, perspiration, or a scratch on the
glass can cause the bulb to overheat
and shatter.
\f—\f—\fy
\f

y
()-
\fy\f
\fy
2008 MDX

Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb f rom the f og
light assembly by turning it one-
quarter turn counterclockwise.Remove the two bolts, and remove
the rear light assembly f rom the
rear pillar.
Open the tailgate. Use a flat-tip
screwdriver protected with a cloth
to pry open the two covers.
Determine which of the two bulbs
is burned out: turn signal/hazard
lights or side marker light.
1. 2.
3.
3.
4.
Lights
Replacing Rear Bulbs
(in Rear Pillar)
406
CONNECTOR
INNER FENDER COVER
BOLT
BOLT
\f—\f—\fy
\f
y
()-
\fy\f

y
2008 MDX

CONT INUED
Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket.Push the new bulb straight into
the socket until it bottoms.
Turn on the lights to make sure
the new bulb is working.
Put the socket back into the light
assembly, and turn it clockwise to
lock it in place.
Install the rear light assembly in
the rear pillar. Tighten the two
bolts. Snap the bolt covers into
position.
Open the tailgate. Place a cloth on
the edge of the light assembly
cover. Remove the cover by
caref ully prying in the notch on its
middle edge with a f lat-tip
screwdriver.
1.
4.
5. 6.
7.
8.
9.
Lights
Replacing a Back-up L ight Bulb
Maint enance
407
COVER
BULB SOCKET
\f—\f—\fy
\f
y
()-
\fy\f
y
2008 MDX

Each outside mirror has side turn
signal lights. The lights should be
replaced by your dealer.
The license plate has two lights
above it. The bulbs should be
replaced by your dealer.
Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
Turn on the lights to make sure
the new bulb is working. Place the cover back into the light
assembly. Push it up until it locks
in place.
Put the socket back into the light
assembly, and turn it clockwise to
lock it in place.
4.
5. 6.
2.
3. 7.
Lights
Side T urn Signal L ight
Rear L icense Plate Bulb
408
BULB
SOCKET
\f—\f—\fy
\f
y
()-
\fy\f
y
2008 MDX

µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
µ
Î
Î
Specif ications
Technical Inf ormation
453
Battery Engine
Fuses
Tires
Alignment
Lights
60 W
12 V
12 V 35 W
12 V 5 W
12 V 5 W
8W
5W
2W
3.4 W
12 V
12 V
12 V
12 V
The low beam headlights are high voltage discharged type.
Replacement of a low beam headlight bulb should be performed by
your dealer.
Capacity 12 V Type
BorexStroke
Displacement
Compression ratio
Spark plugs
11.0 : 1
223.5 cu-in (3,664 cm
)
3.54 x 3.78 in (90.0 x 96.0 mm) Water cooled 4-stroke SOHC
VTEC V6 gasoline engine
Interior
Rear
Under-hood
12 V
12 V
21 W
3CP
SKJ20DR-M11
12 V 3 CP
12 V 18 W
12 V 3 CP
21 W
12 V
12 V 3.4 W 55 W
12 V
12 V 3 CP 60 W
12 V
12 V 65 AH/5 HR
76 AH/20 HR
Size
Pressure 60 psi (420 kPa , 4.2 kgf/cm
)
32 psi (220 kPa , 2.2 kgf/cm)
T165/80D17 104M P255/55R18 104H
Toe-in
Camber
Caster 4°12’
0°30’
0°30’
0.08 in (2.0 mm)
0.00 in (0.0 mm)
Headlights
Daytime running light
Front side marker lights
Front turn signal lights
Parking lights
Fog light
Front foot lights
Rear turn signal lights
Rear side marker light
Backup lights
License plate lights
Individual map lights
Cargo area light
Tailgate light
Vanity mirror light
Door light
IZFR6K11
See page445or the fuse label
attached to the inside of the fuse
box lid.
See page444or the fuse label
attached to the inside of the fuse
box lid.
See page443and 444 or the fuse
box cover.
Front/Rear
Spare
Front/Rear
Spare
Front
Rear
Front
Rear
Front
Front
Rear
High
Low
: (H11)
(HB3)
(D2S)
(HB3)
DENSO:
NGK:
\f—\f—\fy
\fy
()-
\fy\fy
2008 MDX