2008 Acura MDX lock

ÛÝÛÝ
Key and Remote Unlock Mode
To select whether the driver’s door
unlocks or all the doors unlock when
you unlock the doors with the
remote transmitter, follow these
instructions.
You can choose this customize item
f rom ‘‘DOOR/WINDOW SETUP’’ by
pressing the INFO ( / ) button
repeatedly.Press the SEL/RESET button to see
the selections.
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to ‘‘KEY
AND REMOTE UNLOCK MODE’’
and repeat the procedure again.
Select the desired setting by
pressing the INFO ( / ) button,
then enter your selection by pressing
the SEL/RESET button.
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
109
\f—\f—\fy\f
y
()-
\fy\f

y
2008 MDX

ÛÝÛÝ
Keyless Lock Acknowledgment
When you push the LOCK button on
the remote transmitter, some
exterior lights f lash, and a beeper
sounds when you push the LOCK
button again within 5 seconds to
verify that the doors and the tailgate
arelockedandthesecuritysystem
has set (see page ). You can
customize the exterior lights not to
f lash and the beeper not to sound.
You can choose this customize item
f rom ‘‘DOOR/WINDOW SETUP’’ by
pressing the INFO ( / ) button
repeatedly.Press the SEL/RESET button to see
the selections.
Select ON or OFF by pressing the
INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button.
269
Multi-Inf ormation Display
110
\f—\f—\fy\fy
()-
\fy\f

y
2008 MDX

ÛÝ
Security Relock Timer
If you unlock the doors and the
tailgate with the remote transmitter,
but do not open any of the doors or
thetailgatewithin30seconds,the
doors and the tailgate automatically
relock and the security system sets.
You can change this relock time
f rom 30 seconds to 60 or 90 seconds.You can choose this customize item
f rom ‘‘DOOR/WINDOW SETUP’’ by
pressing the INFO ( / ) button
repeatedly.
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘KEYLESS LOCK
ACKNOWLEDGMENT’’ and repeat
the procedure again.
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
111
\f—\f—\fy\f
y
()-
\fy\f

y
2008 MDX

ÛÝ
Press the SEL/RESET button to see
the selections.
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘SECURITY RELOCK TIMER’’ and
repeat the procedure again.
Select the desired setting by
pressing the INFO ( / ) button,
then enter your selection by pressing
the SEL/RESET button.
Multi-Inf ormation Display
112
\f—\f—\fy\fy
()-
\fy\f

y
2008 MDX

Î
Î
Î
Î
Î
Î To use the horn, press the center pad of the steering wheel. If equipped
1:
2:
Controls Near the Steering Wheel
Inst rument s and Cont rols
115
DRIVING POSITION
MEMORY SYSTEM VEHICLE STABILITY
ASSIST SYSTEM
OFF SWITCH
REAR WINDOW
DEFOGGER
HAZARD WARNING
BUTTON
MIRROR CONTROLS PASSENGER AIRBAG
OFF INDICATOR INSTRUMENT PANEL
BRIGHTNESS
WINDSHIELD
WIPERS/WASHERS
STEERING WHEEL
AUDIO CONTROLS
FUEL FILL DOOR
RELEASE BUTTON HEADLIGHT/TURN SIGNAL/
FRONT FOG LIGHTS
POWER DOOR LOCK
MASTER SWITCH POWER WINDOW
SWITCHES SEAT HEATER
SWITCHES
(P.117)
(P.122)
(P.122) (P.34) (P.123)
(P.116)
(P.118)
(P.130) ACCESSORY POWER
SOCKETS
HORN
HEADLIGHT WASHER
SWITCH
ACTIVE DAMPER
SYSTEM SWITCH
(P.233)
(P.360)
(P.155)
(P.157)
(P.149)
(P.323) (P.166)
(P.148)
(P.361)
CRUISE CONTROL
BUTTONS
STEERING WHEEL
ADJUSTMENTS
(P.124)
POWER TAILGATE
BUTTON (P.132)
HOOD RELEASE
HANDLE
(P.325) (P.270)
2
1
1
1
——yy
()-
y
y
2008 MDX

The headlight washers can be
operated at any time by pressing the
headlight washer button located next
to the steering wheel column. The
headlights must be turned on to use
this button. In addition, the headlight
washer operates without pressing
the button, at the first time you turn
on the windshield washers af ter you
turn the ignition switch to the ON
(II) position.The headlight washers use the same
f luid reservoir as the windshield
washers.
Rotate the switch clockwise to
turn the rear window wiper ON.
Hold past ON to turn the rear
window wiper on and to spray the
rear window washer.
1.
2.
CONT INUED
Windshield Wipers and Washers
Headlight Washers
(On Canadian models)Rear Window Wiper and Washer
Inst rument s and Cont rols
117
\f—\f—\fy\f
y
()-
\fy\f
y
2008 MDX

µµ
Rotate the switch
counterclockwise to spray the
window washer.
When you shif t the transmission
to the reverse position with the
f ront windshield wipers activated,
the rear window wiper operates
automatically.
When the wiper control lever
position is INT, the rear wiper
operates intermittently. When it is
LO or HI, the rear wiper operates
continuously. Push down on the
lever to signal a lef t turn and up to
signal a right turn. To signal a lane
change, push lightly on the lever,
and hold it. The lever will return to
center when you release it or
complete a turn.
Turning the switch to the ‘‘ ’’
position turns on the headlights. If
you leave the lights on with the key
removed f rom the ignition switch,
you will hear a reminder chime when
you open the driver’s door.
Turn signal
Of f
Parking and indicator lights
AUTO
Headlights on
High beams
Flashhighbeams
Fog lights of f
Fog lights on
Therearwindowwasherusesthe
same f luid reservoir as the wind-
shield washer. When you turn the wiper switch to
the ‘‘OFF’’ position, the wiper will
return to its parked position.
Turning the
switch to the ‘‘ ’’ position turns
on the parking lights, taillights,
instrument panel lights, side-marker
lights, and rear license plate lights.
1.
2.
3.
4.
5.
6.
7.
8.
9.
3.
4.
Turn Signal
Turn Signal and Headlights
Headlights On
Windshield Wipers and Washers, Turn Signal and Headlights
118
\f—\f—\fy\fy
()-
\fy\f
y
2008 MDX

µµ
When the light switch is in either of
these positions, the lights on
indicator comes on as a reminder.
This indicator stays on if you leave
the lights on and turn the ignition
switch to the ACCESSORY (I) or
LOCK (0) position.
To switch f rom low
beams to high beams, push the lef t
lever f orward until you hear a click.
The blue high beam indicator will
come on (see page ). Pull it back
to return to low beams. To flash the
high beams, pull the lever back
lightly, then release it. The high
beamsstayonaslongasyouhold
the lever back. Even with the automatic lighting
f eature turned on, we recommend
thatyouturnonthelightsmanually
when driving at night or in a dense
f og, or when you enter dark areas
such as long tunnels or parking
f acilities.
To change the ‘‘AUTO LIGHT
SENSITIVITY’’ setting, see page
.
Do not leave the light switch in
AUTO if you will not be driving the
vehicle f or an extended period (a
weekormore).Youshouldalsoturn
of f the lights if you plan to leave the
engine idling or of f f or a long time.
The automatic lighting
f eature turns on the headlights and
all other exterior lights, when it
senses low ambient light.
To turn on automatic lighting, turn
the light switch to AUTO at any time.
The lights will come on automatically
when the outside light level becomes
low (at dusk, f or example). The
lights on indicator comes on as a
reminder. The lights and indicator
will turn of f automatically when the
system senses high ambient light.
The lights will remain on when you
turn of f the ignition switch. They will
turn of f automatically when you
remove the key and open the driver’s
door. To turn them on again, either
turn the ignition switch to the ON
(II) position or turn the light switch
to the position.
70
103
Headlights
High BeamsAUTO
Inst rument s and Cont rols
119
\f—\f—\fy\fy
()-
\fy\f
y
2008 MDX