2008.5 Peugeot 1007 Dag spare wheel
[x] Cancel search: spare wheelPage 97 of 194
6
93
This message is also dis-
played when one of the
wheels is away from the
v e h i c l e ( b e i n g r e p a i r e d ) o r
when one or more wheels
w i t h o u t a s e n s o r a r e fi t t e d .
T h e s p a r e w h e e l i s n o t fi t t e d w i t h a
sensor.
All repairs and changing of
t y r e s o n a w h e e l fi t t e d w i t h
this system must be carried
out by a PEUGEOT dealer.
If, when changing a tyre, you install
a wheel which is not detected by
y o u r v e h i c l e ( e x a m p l e : fi t t i n g o f s n o w
t y r e s ) , y o u m u s t h a v e t h e s y s t e m
reinitialised by a PEUGEOT dealer.
Puncture
This warning light and the
STOP warning light come
on on the instrument panel,
accompanied by an audible
signal and a message on the multi-
function display locating the wheel
concerned.
S t o p i m m e d i a t e l y , a v o i d i n g a n y
s u d d e n m o v e m e n t o f t h e s t e e r i n g
wheel and the brakes.
Change the damaged wheel
( p u n c t u r e d o r v e r y d e fl a t e d
t y r e ) , a n d h a v e t h e t y r e p r e s s u r e
checked as soon as possible.
Sensor(s) not detected or faulty This warning light comes
on on the instrument panel,
accompanied by an audible
signal and a message on the
multifunction display locating the wheel
or wheels which are not detected or
indicating a fault in the system.
Contact a PEUGEOT dealer to re-
place the faulty sensor(s). This system does not elimi-
n a t e t h e n e e d t o h a v e t h e
tyre pressure checked regu-
l a r l y ( r e f e r t o t h e " I d e n t i fi c a -
tion features" paragraph) to ensure
that the optimum dynamic perfor-
m a n c e o f t h e v e h i c l e i s m a i n t a i n e d
a n d p r e v e n t p r e m a t u r e w e a r o f t h e
t y r e s , p a r t i c u l a r l y i n a r d u o u s d r i v i n g
c o n d i t i o n s ( h e a v y l o a d , h i g h s p e e d ) .
The tyre pressures must be checked
cold, at least once a month. Remember
to check the pressure of the spare
wheel.
T h e t y r e u n d e r - i n fl a t i o n d e t e c t i o n
s y s t e m m a y e x p e r i e n c e t e m p o r a r y
interference due to radioelectric
emissions on a frequency close to
that used by the system.
Page 123 of 194
9
117
Parking the vehicle
- If possible, park the vehicle on level, stable and non-slippery
ground.
- It is imperative that you ensure that the occupants get out of the vehi-
cle and wait in a safe location.
- Apply the handbrake, switch off t h e i g n i t i o n a n d e n g a g e fi r s t o r
reverse gear (position R for the
"2 Tronic" gearbox).
CHANGING A WHEEL
1. Jack with integrated handle.
2. Chock.
3. Wheelbrace.
4. Extension.
5. "Bolt cover" tool.
6. Removable towing eye. Access to the spare wheel and
the jack
The wheel is located outside the ve-
h i c l e , u n d e r t h e r e a r fl o o r , s u p p o r t e d
by a metal carrier.
- Unclip the cover to gain access
to the spare wheel carrier retain-
ing bolt, located on the inside
near the closing system.
- Using the wheelbrace 3 and the
extension 4 , slacken the spare
wheel carrier retaining bolt.
- Lift the carrier to release the hook rearwards, then lower it.
- Remove the spare wheel and the box.
- Remove the jack 1 from the box.
Tools provided
The jack is stored in a box in the cen-
tre of the spare wheel. The chock is
fi x e d o n t h e s i d e o f t h e b o x .
The other tools are stored in a case
in the left boot trim.
Note: i f y o u r v e h i c l e i s fi t t e d w i t h a
towbar, the case is stored in the left
s t o r a g e t r a y ( l o c a t e d i n t h e fl o o r o f
the rear footwell).
Page 124 of 194
9
118
Removing a wheel
- Place the chock 2 (integrated
with the box) at the rear of the
wheel diagonally opposite the
wheel to be changed.
- Remove the wheel trim, using the wheelbrace 3 , by pulling at
the valve passage hole.
- Remove the chrome-plated bolt covers and the plastic cover from
the bolts using the "bolt cover" tool 5
(Special features of alloy wheels).
- Slacken the wheel bolts.
- Place the jack 1 under one of the
four locating points A on the sub-
frame closest to the wheel to be
changed. Ensure that the entire
surface of the jack base plate is
in contact with the ground.
-
Extend the jack, completely unscrew
the bolts and remove the wheel.
Refitting the wheel
- Position the wheel on the hub.
- Lightly pre-tighten the bolts us- ing the wheelbrace 3 .
-
Compress the jack 1 and release it.
- Fully tighten the bolts using the wheelbrace.
- Replace the trim, starting at the valve passage hole, and press it
on using the palm of the hand.
For your safety, always
change a wheel:
- Stow the tools in the case, then
put it back in the left boot trim.
T h e j a c k a n d t h e t o o l k i t a r e s p e c i fi c
to your vehicle. Do not use them for
other purposes.
Replacing the wheel in the
carrier
- Replace the jack 1 in the box.
- Replace the box in the wheel.
- Replace the wheel in the carrier.
- Lift the wheel then the carrier and reposition the hook.
- Do not forget to fully tighten the spare wheel carrier retaining bolt. After changing the wheel
- Have the tightening of the bolts
and the pressure of the spare
tyre checked as soon as possi-
ble by a PEUGEOT dealer.
- Do not exceed its maximum au- thorised speed: 50 mph (80 km/h).
- Have the punctured tyre repaired and replace it on the vehicle as
soon as possible.
- 15 and 16 inch punctured wheels cannot be placed in the carrier.
- on level, stable and non-slippery
ground,
- with the handbrake applied,
- w i t h fi r s t o r r e v e r s e g e a r e n g a g e d (position R for the "2 Tronic" gear-
box),
- with the vehicle chocked,
- never go underneath a vehicle raised using a jack (use an axle
stand).
Page 125 of 194
9
119
Special features of alloy
wheels Fitting the spare wheel
I f y o u r v e h i c l e i s fi t t e d w i t h a s t e e l
s p a r e w h e e l , w h e n fi t t i n g i t , i t i s
nor-
mal when tightening the bolts to no-
tice that the washers do not come
into contact with the rim. The spare
wheel is secured by the cone shape
of each bolt. Anti-theft bolts
I f y o u r w h e e l s a r e fi t t e d w i t h a n a n t i -
theft bolt (one per wheel), the chrome
trim must be removed before un-
screwing the bolt using the anti-theft
socket and the wheelbrace.
Fitting snow tyres
I f y o u fi t s n o w t y r e s m o u n t e d o n s t e e l
wheels onto your vehicle, it is es-
sential to use special bolts available
from PEUGEOT dealers.
Wheels equipped with 195/50R16
t y r e s c a n n o t b e fi t t e d w i t h s n o w
chains.
For further information, contact a
PEUGEOT dealer.
Bolt covers
Alloy wheel bolts are covered by
chrome trims.
Use the yellow tool to remove the
trims before slackening the bolts.
Page 138 of 194
9
131
ACCESSORIES FOR YOUR 1007
A wide range of accessories recom-
mended by PEUGEOT and original
parts are offered by the Network.
T h e y a l l b e n e fi t f r o m P E U G E O T ' s
recommendation.
These accessories and parts, having
been tested and approved for reli-
ability and safety, are all adapted to
your PEUGEOT vehicle. T h e fi t t i n g o f e l e c t r i c a l e q u i p -
ment or accessories which
are not recommended by
PEUGEOT may result in a
failure of your vehicle's electronic
system.
P l e a s e n o t e t h i s s p e c i fi c w a r n i n g .
You are advised to contact a repre-
sentative of the Marque to be shown
the range of recommended equip-
ment and accessories.
Depending on the country in which
the vehicle is sold, it is compulsory to
have a safety jacket, warning trian-
gle and spare bulbs available in the
vehicle.
"Protection": anti-theft
alarm , engraved windows,
wheel anti-theft devices,
system which assists with
t h e i d e n t i fi c a t i o n o f a s t o l e n
v e h i c l e , fi r s t a i d k i t , w a r n -
ing triangle, high visibility
safety jacket, fog lamps kit,
snow chains, non-skid cov-
ers, audible rear parking
assistance.
"Touring": central arm-
rest, storage under the rear
shelf, mats * , boot tray, sun
blinds.
For leisure pursuits: roof
bars, transportation ac-
cessories (bicycle carrier,
ski carrier), roof box, child
seats and booster cushions, audio/
telephone console, cool box.
"In-Car Technology": hands-
free kits, satellite navigation
systems, CD changer, DVD
player, multimedia, audio
equipment, speakers, auxil-
iary audio socket permitting
the connection of a portable
MP3 player (compatible with
WIP Sound), USB socket.
"Styling": seat covers, al-
loy wheels, wheel trims,
spoiler, styling strips, door
spoilers, sill protectors,
aluminium footrest, rear si-
lencer, exhaust tail pipe.
"Universal": windscreen
w a s h fl u i d , i n t e r i o r a n d e x -
terior cleaning and mainte-
nance products.
You can obtain "Van" conver-
sion kits for conversion from
a private vehicle to a van.
You can obtain other
"Cameleo" customising kits
from PEUGEOT dealers.
You will be offered either a
complete kit, like the original kit, or a
partial kit consisting of the vent trims
only.
Should you need to change one or
more elements of the Cameleo kit of
your vehicle, due to damage..., you
will be offered replacement elements
from the exchange kits available at
that time.
This product range offered by PEUGEOT
Accessories is structured around 5 catego-
ries: PROTECTION - TOURING - IN-CAR
TECHNOLOGY - STYLING - UNIVERSAL.
* To prevent jamming under the
pedals:
- ensure that the mat is positioned and secured correctly,
- n e v e r fi t o n e m a t o n t o p o f a n - other.
T r a i l e r t o w b a r w h i c h m u s t b e fi t t e d b y
the PEUGEOT network.