2008.5 Peugeot 1007 Dag brake
[x] Cancel search: brakePage 123 of 194
9
117
Parking the vehicle
- If possible, park the vehicle on level, stable and non-slippery
ground.
- It is imperative that you ensure that the occupants get out of the vehi-
cle and wait in a safe location.
- Apply the handbrake, switch off t h e i g n i t i o n a n d e n g a g e fi r s t o r
reverse gear (position R for the
"2 Tronic" gearbox).
CHANGING A WHEEL
1. Jack with integrated handle.
2. Chock.
3. Wheelbrace.
4. Extension.
5. "Bolt cover" tool.
6. Removable towing eye. Access to the spare wheel and
the jack
The wheel is located outside the ve-
h i c l e , u n d e r t h e r e a r fl o o r , s u p p o r t e d
by a metal carrier.
- Unclip the cover to gain access
to the spare wheel carrier retain-
ing bolt, located on the inside
near the closing system.
- Using the wheelbrace 3 and the
extension 4 , slacken the spare
wheel carrier retaining bolt.
- Lift the carrier to release the hook rearwards, then lower it.
- Remove the spare wheel and the box.
- Remove the jack 1 from the box.
Tools provided
The jack is stored in a box in the cen-
tre of the spare wheel. The chock is
fi x e d o n t h e s i d e o f t h e b o x .
The other tools are stored in a case
in the left boot trim.
Note: i f y o u r v e h i c l e i s fi t t e d w i t h a
towbar, the case is stored in the left
s t o r a g e t r a y ( l o c a t e d i n t h e fl o o r o f
the rear footwell).
Page 124 of 194
9
118
Removing a wheel
- Place the chock 2 (integrated
with the box) at the rear of the
wheel diagonally opposite the
wheel to be changed.
- Remove the wheel trim, using the wheelbrace 3 , by pulling at
the valve passage hole.
- Remove the chrome-plated bolt covers and the plastic cover from
the bolts using the "bolt cover" tool 5
(Special features of alloy wheels).
- Slacken the wheel bolts.
- Place the jack 1 under one of the
four locating points A on the sub-
frame closest to the wheel to be
changed. Ensure that the entire
surface of the jack base plate is
in contact with the ground.
-
Extend the jack, completely unscrew
the bolts and remove the wheel.
Refitting the wheel
- Position the wheel on the hub.
- Lightly pre-tighten the bolts us- ing the wheelbrace 3 .
-
Compress the jack 1 and release it.
- Fully tighten the bolts using the wheelbrace.
- Replace the trim, starting at the valve passage hole, and press it
on using the palm of the hand.
For your safety, always
change a wheel:
- Stow the tools in the case, then
put it back in the left boot trim.
T h e j a c k a n d t h e t o o l k i t a r e s p e c i fi c
to your vehicle. Do not use them for
other purposes.
Replacing the wheel in the
carrier
- Replace the jack 1 in the box.
- Replace the box in the wheel.
- Replace the wheel in the carrier.
- Lift the wheel then the carrier and reposition the hook.
- Do not forget to fully tighten the spare wheel carrier retaining bolt. After changing the wheel
- Have the tightening of the bolts
and the pressure of the spare
tyre checked as soon as possi-
ble by a PEUGEOT dealer.
- Do not exceed its maximum au- thorised speed: 50 mph (80 km/h).
- Have the punctured tyre repaired and replace it on the vehicle as
soon as possible.
- 15 and 16 inch punctured wheels cannot be placed in the carrier.
- on level, stable and non-slippery
ground,
- with the handbrake applied,
- w i t h fi r s t o r r e v e r s e g e a r e n g a g e d (position R for the "2 Tronic" gear-
box),
- with the vehicle chocked,
- never go underneath a vehicle raised using a jack (use an axle
stand).
Page 128 of 194
9
122
Rear lights
1. Brake/side lights
(P21 W/5 W).
2. Direction indicators (P21 W).
3. Reversing light (P21 W), right
side.
Fog lamp (P21 W), left side.
These 4 bulbs are changed by re-
moving the light:
R e m o v e t h e a c c e s s fl a p i n t h e
corresponding boot side trim to
access the light,
R e m o v e t h e t w o l i g h t fi x i n g n u t s
inside the boot,
Unclip the harness,
Remove the light pressing on the
retaining tabs,
Remove the seal,
Remove the bulb holder moving
aside the two tabs A ,
Turn the bulb a quarter of a turn,
Remove the bulb and change it.
Note: if necessary, use the wheel-
brace to remove the nuts.
W h e n r e fi t t i n g , p r o c e e d i n t h e r e -
verse order and take care to position
the bulb holder, the seal and the light
correctly. Third brake light
(4 W 5 W bulbs)
Using a 10 mm box spanner, un-
s c r e w t h e 2 fi x i n g n u t s A .
Release the lamp unit by push-
ing it outwards.
Disconnect the connector and
the rear wash-wipe pipe.
Turn the bulb holder a quarter of
a turn and remove it.
Remove the bulb and change it.
W h e n r e fi t t i n g , p r o c e e d i n t h e r e -
verse order and ensure that the lamp
unit seal and the rear wash-wipe pipe
have been put back in place correctly.
Do not tighten the nuts more than is
necessary at the risk of breaking the
light.
Number plate lights (W 5 W)
Insert a thin screwdriver into one
of the external holes of the lens.
Push it outwards to unclip it.
Remove the lens.
Remove the bulb and change it.
Page 131 of 194
9
124
Fuse N°RatingFunctions
115 ARear wiper.
35 AAir bags and pre-tensioners control unit.
410 ADiagnostic socket - Clutch switch - Steering wheel angle sensor - P a r t i c l e e m i s s i o n fi l t e r p u m p .
530 AElectric windows - Sunroof.
6-Not used.
75 ACourtesy light - Glove box lighting.
820 A T y r e u n d e r - i n fl a t i o n d e t e c t i o n c o n t r o l u n i t - E l e c t r i c m i r r o r f o l d i n g - A l a r m s i r e n - Multifunction display - Alarm control unit - Audio equipment - Aud io/telephone.
930 AAudio equipment - Lighter/12 V socket (100 W max).
1015 ASteering wheel controls.
1115 ADiagnostic socket - Low current ignition switch - Motorised strikers.
1215 AAir bags and pre-tensioners control unit - Rain/brightness sensor.
135 AABS relay - Speed sensor - Engine Fuse Box - "2 Tronic" gear lever - Brake swit ch.
1415 AParking assistance control unit - "Sesame" doors control unit and switches - Instrument panel - Seat belt warning lights bar - Air conditioning control panel - Headlamp adjustment - Hands-free kit.
1530 ALocking - Deadlocking - Unlocking.
1740 ARear screen and exterior mirrors demisting.
SH-PARC shunt.
Page 133 of 194
9
126
Fuse N°RatingFunctions
120 AEngine control unit supply and fan assembly control - Engine control unit main relay - Injection control unit (Diesel) - Injection pump (Diesel) - Air heating solenoid valves (Diesel) - A i r fl o w s e n s o r ( D i e s e l ) .
215 AHorn.
310 AFront and rear wash-wipe pump.
420 AHeadlamp wash pump.
515 AFuel pump (petrol).
610 APower steering control unit - Water in diesel sensor - Vehicle spe ed sensor.
710 ASwitching and protection unit (Diesel) - Engine coolant level detector (Diesel).
825 AStarter.
910 AABS/ESP control unit - ABS cut-off relay - Brake switch.
1030 A
Engine control unit actuators (petrol: ignition coils, oxygen se nsors, injectors, purge canister and variable timing solenoid valves, controlled thermosta t) (Diesel: injection c o n t r o l u n i t , a i r fl o w s e n s o r , i n j e c t i o n p u m p , d i e s e l h i g h p r e s s u r e r e g u l a t o r , E G R a n d T u r b o pressure regulation solenoid valves) - Blow-by heaters - Diesel heate r.
1140 AAir blowers.
1230 AWindscreen wipers (low/high speed).
1340 A(ignition positive) Built-In Systems Interface.
14-Not used.
1510 ARight main beam headlamp.
1610 ALeft main beam headlamp.
1715 ALeft dipped headlamp.
1815 ARight dipped headlamp.