2008.5 Peugeot 1007 Dag ESP
[x] Cancel search: ESPPage 79 of 194
4
80
Automatic central locking
The doors can lock automatically
when you are driving (at a speed of
more than 6 mph (10 km/h).
You can activate or deactivate this
function. Driving with the doors locked
may make access to the pas-
senger compartment by the
emergency services more
d i f fi c u l t i n a n e m e r g e n c y .
Activation
With the ignition on, press and hold
button A .
Activation of the function is accompa-
nied by an audible signal and a mes-
sage on the multifunction display.
Deactivation
With the ignition on, press and hold
button A .
Deactivation of the function is
accompanied by an audible signal
and a message on the multifunction
display.
"Door open" alert -
when the vehicle is moving,
by lighting of the "door open"
warning light, accompanied by
an audible signal and a message
on the multifunction display for a
few seconds.
Opening/Closing using the
remote control
Press button C or D to open or close
the left or right door.
The opening and closing of the door is
accompanied by an audible signal.
2nd press on button C or D during
opening/closing interruption of the
movement.
3rd press on button C or D move-
ment of the door in the opposite
direction.
You are advised to use the
remote control or the controls
as much as possible.
Opening/Closing from the front
Press switch
B to open or close the
corresponding door.
Choosing the movement of the door
using the controls:
- pull opens the door,
- push closes,
- second press stops the
movement,
- the controls do not function above 3 mph (5 km/h).
If a door or the boot is not
closed properly, you are
warned:
- when the engine is running,
by lighting of the "door open"
warning light, accompanied by
a message on the multifunction
display for a few seconds.
Page 84 of 194
4
84
PANORAMIC SUNROOF
This sunroof is a panoramic assembly
which provides maximum brightness
and visibility in the passenger com-
partment.
It consists of two parts:
- a fi x e d r e a r p a r t ,
- a moving front part.
Each part has an independent manual
shutter.
The sunroof is controlled electrically
by a dial with 9 opening positions. Operation
To open: turn the dial to the left (nine
possible settings).
Once the roof is open, the front shutter
cannot be closed.
To close: return the control to the
initial position "O" . Reinitialisation
Following reconnection of the bat-
tery, in the event of a malfunction or
in the event of unwanted opening of
the roof on closing, the safety auto-
reverse must be reinitialised:
- place the dial in the fully closed
position (initial position "O" ),
- press the dial immediately,
- continue to press until the roof is fully closed.
Always remove the ignition
key when leaving the vehi-
cle, even for a short time.
In the event of contact during
operation of the roof, the movement
of the roof must be reversed. To do
this, operate the control concerned.
When the driver operates the roof
control, he must ensure that no one
is preventing the roof from closing
correctly.
The driver must ensure that the pas-
sengers use the sunroof correctly.
Be aware of children when operating
the roof.
Check that the slides are clean to en-
sure that the sunroof slides correctly.
Safety auto-reverse
When the roof meets an obstacle
while closing, it partially opens again.
You can close the sunroof
using the remote control
when locking (refer to the
corresponding chapter).
The safety auto-reverse function is
not operational during this operation.
Page 94 of 194
5
91
COURTESY LIGHT
1. Front courtesy light
2. Map reading lights In the permanently on posi-
tion, there are different dura-
tions of lighting:
Boot light
The boot light is located in the left
boot trim.
It comes on automatically when the
boot is opened and switches of auto-
matically when the boot is closed.
Front courtesy light Permanently off.
Permanently on.
In this position, the courtesy
light comes on gradually:
- when the vehicle is unlocked,
- when the key is removed from the ignition,
- when the remote control locking button is pressed, in order to
locate your vehicle.
It switches off gradually:
- when the vehicle is locked,
- when the ignition is switched on,
- 30 seconds after the last door is closed. Map reading lights
With the ignition on, press
the corresponding switch 2 .
- when the ignition is off, approxi-
mately ten minutes,
- in energy economy mode, ap- proximately thirty seconds,
- when the engine is running, no limit.
Page 99 of 194
6
95
If this warning light comes on
on the instrument panel and
the indicator light on the but-
ton comes on, this indicates
that the ASR and ESP sys-
tems are disarmed.
TRACTION CONTROL (ASR) AND DYNAMIC STABILITY CONTROL (ESP)
Operation of the ASR and ESP
systems T h e w a r n i n g l i g h t fl a s h e s i f
t h e A S R o r E S P i s a c t i v a t e d . Disarming
I n e x c e p t i o n a l c o n d i t i o n s ( s t a r t i n g a
v e h i c l e w h i c h i s b o g g e d d o w n , s t u c k
in snow, on soft ground, ...), it may
b e a d v i s a b l e t o d i s a r m t h e A S R a n d
ESP systems, so that the wheels can
m o v e f r e e l y a n d r e g a i n g r i p .
Press the "ESP OFF" button,
located in the centre of the
fascia.
Reactivation T h e s e s y s t e m s a r e r e a c t i v a t e d a u t o -
matically each time the ignition is
switched back on or from 30 mph
(50 km/h).
Press the "ESP OFF" button again
t o r e a c t i v a t e t h e m m a n u a l l y .
Operating fault
If this warning light comes on,
accompanied by an audible
signal and a message on the
multifunction display, this indi-
cates a malfunction of these
systems.
H a v e t h e s y s t e m s c h e c k e d b y a
PEUGEOT dealer.
T h e E S P / A S R s y s t e m s o f f e r e x c e p -
t i o n a l s a f e t y i n n o r m a l d r i v i n g , b u t
t h i s s h o u l d n o t e n c o u r a g e t h e d r i v e r
t o t a k e e x t r a r i s k s o r d r i v e a t h i g h
speed.
The correct functioning of these
s y s t e m s d e p e n d s o n o b s e r v a t i o n o f
the manufacturer's recommenda-
tions regarding the wheels (tyres
and rims), the braking components,
the electronic components and the
PEUGEOT assembly and operation
procedures.
A f t e r a n i m p a c t , h a v e t h e s e s y s t e m s
checked by a PEUGEOT dealer.
Activation of the ASR and ESP
systems
When the ignition is on, the ASR and
E S P s y s t e m s a r e a l w a y s a c t i v e .
These systems are linked and com-
plement the ABS.
T h e A S R s y s t e m o p t i m i s e s d r i v e t o
p r e v e n t t h e w h e e l s s k i d d i n g , b y a c t -
i n g o n t h e b r a k e s o f t h e d r i v e w h e e l s
and on the engine. It also allows the
d i r e c t i o n a l s t a b i l i t y o f t h e v e h i c l e t o
b e i m p r o v e d o n a c c e l e r a t i o n .
I f t h e r e i s a v a r i a t i o n b e t w e e n t h e t r a -
j e c t o r y f o l l o w e d b y t h e v e h i c l e a n d
t h a t r e q u i r e d b y t h e d r i v e r , t h e E S P
system automatically acts on the
engine and the brake of one or more
w h e e l s , i n o r d e r t o p u t t h e v e h i c l e
back on course, within the limits of
the laws of physics.
Page 101 of 194
6
97
Seat belt not fastened warning I f t h e d r i v e r a n d / o r t h e
front passenger has not
fastened his seat belt,
the corresponding warn-
ing light comes on when
the ignition is on, then, at a speed
a b o v e 1 2 m p h ( 2 0 k m / h ) , t h i s i s a c c o m -
p a n i e d b y a n a u d i b l e s i g n a l t h e v o l u m e
o f w h i c h i n c r e a s e s ( f o r a p p r o x i m a t e l y
two minutes) and a message on the
multifunction display.
Note: a bag or an animal placed on
the front passenger seat may trigger
lighting of the warning light.
Seat belt unfastened warning
I f t h e d r i v e r a n d / o r o n e
of the passengers has
unfastened his seat
belt, the corresponding
warning light comes on
when the engine is running, then, at a
s p e e d a b o v e 1 2 m p h ( 2 0 k m / h ) , t h i s
is accompanied by an audible signal
t h e v o l u m e o f w h i c h i n c r e a s e s ( f o r
a p p r o x i m a t e l y t w o m i n u t e s ) a n d a
message on the multifunction display.
Rear seat belts
T h e r e a r s e a t s a r e fi t t e d w i t h t w o
three-point inertia reel seat belts.
The retaining of the rear seat belt
buckle by the sliding block makes
folding down or complete folding of
the seats easier.
Fastening
Pull the strap, then insert the
buckle in the stalk.
Check that the seat belt is
fastened correctly by pulling the
strap.
Unfastening
Press the red button on the stalk.
Version with colour display
I f t h e d r i v e r a n d / o r o n e o f t h e p a s -
sengers has not fastened (or has
unfastened) his seat belt, a message
appears on the multifunction display.
Page 113 of 194
7
106
Operating fault
If a speed limiter malfunction occurs,
t h e s p e e d i s r e p l a c e d b y fl a s h i n g
dashes. Contact a PEUGEOT dealer
to have the system checked.
Activating/deactivating the limiter
Switch the speed limiter on by
pressing button 4 .
Programming
Place the dial 1 in the LIMIT posi-
tion. The limiter is not yet active.
By default, the display indicates
the last speed programmed: Return to normal driving
Turn dial 1 to position "0" : the
speed limiter mode is deselected.
The display returns to the dis-
tance recorder.
In the event of a steep de-
scent or sharp acceleration,
the speed limiter will not be
able to prevent the vehicle
from exceeding the pro-
grammed speed.
In any event, the speed limiter cannot
replace the need to observe speed
limits, nor can it replace the need for
vigilance and responsibility on the
part of the driver.
The driver must remain alert and stay
in complete control of his vehicle.
To prevent the mat from becoming
caught under the pedals:
- ensure that the mat is positioned correctly.
- n e v e r fi t o n e m a t o n t o p o f a n o t h e r .
Set the speed value by press-
ing button 2 or 3 ( e . g . : 7 0 m p h
( 1 1 0 k m / h ) ) .
You can then change the programmed
speed using buttons 2 and 3 :
- b y + o r - 1 m p h ( 1 k m / h ) = s h o r t press,
-
b y + o r - 5 m p h ( 5 k m / h ) = l o n g p r e s s ,
- i n s t e p s o f + o r - 5 m p h ( 5 k m / h ) = maintained press. Exceeding the programmed
speed
Pressing the accelerator pedal to
exceed the programmed speed will
not have any effect, unless you press
the pedal
fi r m l y passing the point of
resistance .
The speed limiter is deactivated tem-
porarily and the programmed speed,
w h i c h i s s t i l l d i s p l a y e d , fl a s h e s .
Returning to the programmed speed,
by means of intentional or uninten-
tional deceleration of the vehicle,
c a n c e l s t h e fl a s h i n g a u t o m a t i c a l l y
and reactivates the speed limiter.
Switch the speed limiter off by
pressing button 4 : the display
c o n fi r m s t h a t i t i s o f f ( O F F ) .
Switch the speed limiter back on
by pressing button 4 again.
Page 114 of 194
7
1 0 7
CRUISE CONTROL
This cruise control, of the new genera-
tion, is linked with the speed limiter. It
has a display on the instrument panel
to indicate the memorised reference
speed.
It enables the vehicle to maintain a
steady speed programmed by the
driver.
The cruise control is switched on
manually: it requires a minimum ve-
h i c l e s p e e d o f 2 5 m p h ( 4 0 k m / h ) a n d
fourth gear must be engaged on the
manual gearbox.
The cruise control is switched off
by means of a manual action or by
pressing the brake or clutch pedal or
in the event of activation of the ESP.
By pressing the accelerator pedal, it is
possible to exceed the programmed
speed temporarily.
To return to the programmed speed,
simply release the accelerator pedal.
Switching off the ignition or turning
the dial cancels any programmed
speed value. Instrument panel display
The programmed information is
grouped together on the instrument
panel display.
5. Cruise control on/off indication
6. Cruise control mode selection in-
dication
7. Programmed speed value
Steering wheel controls
This system's controls are grouped
together on lever
A .
1. Cruise control mode selection dial
2. Value decrease button
3. Value increase button
4. Cruise control on/off button
Page 115 of 194
7
108
Exceeding the programmed speed
Intentional or unintentional exceeding
of the programmed speed results in
fl a s h i n g o f t h e p r o g r a m m e d s p e e d
on the display.
Returning to the programmed speed,
by means of intentional or uninten-
tional deceleration of the vehicle,
c a n c e l s t h e fl a s h i n g a u t o m a t i c a l l y .
Using the accelerator:
exceed the memorised speed until
the required speed is reached,
press button 2 or 3 .
Programming
Place switch 1 in the CRUISE
position. The cruise control is
not yet active and no speed has
been memorised. The display
indicates: Cancelling the cruise control
Switch the cruise control off by
pressing button 4 : the display
c o n fi r m s t h a t i t i s o f f ( O F F ) .
When changing the memo-
rised reference speed by
means of a maintained
press, pay attention as
the speed can increase or
decrease rapidly.
Do not use the cruise control on slip-
p e r y r o a d s o r i n h e a v y t r a f fi c .
In the event of a steep slope, the
cruise control cannot prevent the
vehicle from exceeding the pro-
grammed speed.
In any event, the cruise control can-
not replace the need to comply with
speed limits, nor can it replace the
need for vigilance and responsibility
on the part of the driver.
To prevent the mat from becoming
caught under the pedals:
- ensure that the mat is positioned correctly.
- n e v e r fi t o n e m a t o n t o p o f a n o t h e r .
It is advisable to keep your feet near
the pedals.
Set the programmed speed by
accelerating to the required
speed, then press button 2 or 3
( e . g . : 7 0 m p h ( 1 1 0 k m / h ) ) .
Return to normal driving
Turn dial 1 to position "0" : the
cruise control mode is dese-
lected. The display returns to the
distance recorder. Operating fault
If a cruise control malfunction occurs,
t h e s p e e d i s r e p l a c e d b y fl a s h i n g
dashes. Contact a PEUGEOT dealer
to have the system checked.
You can then change the programmed
speed using buttons 2 and 3 :
- b y + o r - 1 m p h ( 1 k m / h ) = s h o r t press,
-
b y + o r - 5 m p h ( 5 k m / h ) = l o n g p r e s s ,
- i n s t e p s o f + o r - 5 m p h ( 5 k m / h ) = m a i n t a i n e d p r e s s . Reactivating the cruise control
Switch the cruise control back on
by pressing button 4 again.