2008.5 Citroen C4 display

29
I
I N S T R U M E N T S a n d C O N T R O L S
Maintenance indicator zero reset Engine oil level indicator
After each service, the maintenance
indicator must be reset to zero.
Your CITROËN technician resets the
indicator to zero after each service.
However, if you do your own servicing,
the procedure for resetting to zero is
as follows :

 switch off the ignition,

 press and hold the trip distance
recorder zero reset button,


switch on the ignition; the distance re-
corder display begins a countdown,

 when the display indicates "=0" ,
release the button; the spanner
disappears. System which informs the driver
whether the engine oil level is cor-
rect or not.
This information is displayed for a
few seconds when the ignition is
switched on, after the service infor-
mation.
The level read will only be correct if
the vehicle is on level ground and
the engine has been off for more
than 15 minutes.
Oil level correct
Oil level low
This is indicated by the fl ashing of

"OIL" , accompanied by an audible
signal and a message on the multi-
function screen.
If the low oil level is confi rmed by a
check using the dipstick, it is essen-
tial that the level is topped up to pre-
vent damage to the engine. Oil level gauge fault
This is indicated by the fl ashing of

"OIL--" . Contact a CITROËN dealer.
Dipstick
Refer to the "Checks" section to lo-
cate the dipstick and the oil fi ller cap
on your engine. There are 2 marks on
the dipstick:
- A = max; never ex-
ceed this level,
- B = min; top up the
level via the oil fi ller
cap, using the type
of oil suited to your
engine.
Following this operation, if you wish
to disconnect the battery, lock the
vehicle and wait at least fi ve minutes
for the zero reset to be taken into ac-
count.

30
I
I N S T R U M E N T S a n d C O N T R O L S
Total distance recorder
System which measures the total
distance travelled by the vehicle
during its life.
The total and trip distances are dis-
played for thirty seconds when the
ignition is switched off, when the
driver’s door is opened and when
the vehicle is locked or unlocked.
Trip distance recorder
System which measures a distance
travelled during a day or other period
until it is reset to zero by the driver.

 With the ignition on, press the
button until zeros appear. Dashboard lighting rheostat
Activation

 Turn control A or press control B
to adjust the brightness of the
dashboard lighting,

 With control B , press until the
brightness is at maximum, release,
press until you reach minimum.
Deactivation
When the lights are off, or in day
mode in the case of vehicles fi tted
with daytime running lights, the but-
ton has no effect.
System permitting manual adjust-
ment of the brightness of the dash-
board to suit the level of ambient
light.
The rheostat is active if the sidela-
mps are on and applies to:
- the instrument panel,
- the display screens.

31
II
M U L T I F U N C T I O N S C R E E N S
MULTIFUNCTION SCREEN A
Presentation

1. Time

2. Date and display zone

3. Ambient temperature
When the ambient temperature is
between +3 °C and -3 °C, the tem-
perature display fl ashes (ice risk).
The ambient temperature displayed
may be greater than the actual tem-
perature, if the vehicle is parked in
bright sunlight.
The display of certain types of infor-
mation is sometimes by scrolling and
sometimes by alternating between
them.
A. Access to the "Main Menu"

B. Scrolling in the screen menus

C. Confi rmation and selection in the
menus of the function chosen or
the value modifi ed

D. Cancellation of the operation or
return to the previous display

E. Selection of the type of information
to be displayed in zone 2 (date,
radio-CD and trip recorder)

B or F. Within the menus, choice
of activation/deactivation of
functions and selection of
adjustments By pressing button
A , then using
button B , you have access to the fol-
lowing functions:

33
II
M U L T I F U N C T I O N S C R E E N S
MULTIFUNCTION SCREEN C Main Menu
Presentation
Radio-CD
(see "Audio")
Trip computer
This permits:
Bluetooth
®

hands-free kit
(see "Audio")
Controls

1. Time

2. Ambient temperature

3. Date and display zone
When the ambient temperature is
between +3 °C and -3 °C, the tem-
perature display fl ashes (ice risk).
The ambient temperature displayed
may be greater than the actual tem-
perature, if the vehicle is parked in
bright sunlight.
It is recommended that the driver
should not operate the controls
while the vehicle is in motion.
A. Access to the "Main Menu"

B. Scrolling in the screen menus

C. Confi rmation and selection in the
menus of the function chosen or
the value modifi ed

D. Cancellation of the operation or
return to the previous display

E. Selection of the type of informa-
tion to be displayed permanently
(date, radio-CD, trip computer)
on the right of the screen (See
"Trip computer") Press button
A to view the "Main
Menu" of the multifunction screen.
This menu gives you access to the
following functions:
- entering the distance to your destination,
- access to the log of alerts (recall of alerts signalled previously),
- access to the status of functions, such as the activation/deactiva-
tion of the automatic headlamps,
of the automatic windscreen
wipers, of the ESP...

36
II
M U L T I F U N C T I O N S C R E E N S
NAVIDRIVE MULTIFUNCTION COLOUR SCREEN
Presentation

1. Ambinet temperature

2. Directory

3. Date

4. Telephone

5. Time
When the ambient temperature is
between +3 °C and -3 °C, the tem-
perature display fl ashes (risk of ice).
The ambient temperature displayed
may be greater than the actual tem-
perature, if the vehicle is parked in
bright sunlight.
It is recommended that the driver
should not operate the controls
while the vehicle is in motion. Controls
Main Menu

Traffi c Information

Navigation/Guidance

Map

Audio Functions

Telematics

Confi guration,
for adjusting various para-
meters (date, time, units)

Video

Vehicle Diagnostics

A. Access to the "Main Menu"

B. Scrolling in the screen menus

C. Confi rmation and selection in the
menus of the function chosen or
the value modifi ed

D. Cancellation of the operation or
return to the previous display

E. Selection of the type of informa-
tion to be displayed permanently
(date, radio-CD, trip computer)
on the right of the screen Press on the button
A to view the
"Main Menu" of the multifunction
screen.
This menu gives you access to the
following functions (see "NaviDrive
Instructions"):

37
II
M U L T I F U N C T I O N S C R E E N S
TRIP COMPUTER
System which provides current
information concerning the route
travelled (range, consumption...).
Monochrome screen A Data displays

 Press the control for more than
two seconds to reset to zero the
distance travelled, the average
consumption and the average
speed.
Zero reset
The trip computer provides the fol-
lowing information:
- range,
- current consumption,
- distance travelled,
- average consumption,
- average speed.

 The next press then returns you
to the normal display.

 Press the button, located at the
end of the wiper
stalk , to display
the various items of trip compu-
ter data in succession.

38
II
M U L T I F U N C T I O N S C R E E N S
TRIP COMPUTER
System which provides current
information concerning the route
travelled (range, consumption, …).
Monochrome screen C
NaviDrive colour screen Display of information
Trip zero reset

 Press the button, located at the
end of the wiper
stalk , to display
the various trip computer infor-
mation groups in succession:
- the current information group with:

38
II
M U L T I F U N C T I O N S C R E E N S
TRIP COMPUTER
System which provides current
information concerning the route
travelled (range, consumption, …).
Monochrome screen C
NaviDrive colour screen Display of information
Trip zero reset

 Press the button, located at the
end of the wiper
stalk , to display
the various trip computer infor-
mation groups in succession:
- the current information group with: