2008.5 Citroen C3 PICASSO ignition
[x] Cancel search: ignitionPage 107 of 204
!
!
96
If at least one of the two air bag
warning lights come on continu-
ously, do not install a child seat on
the front passenger seat.
Have the system checked by a
CITROËN dealer.
Operating fault If this warning light comes on on
the instrument panel, accompa-
nied by an audible warning and
a message on the multifunction
display, contact a CITROËN dealer to
have the system checked. The air bags
may no longer be triggered in the event
of a serious impact.
Reactivation
When you remove the child seat, turn
switch
1 to the "ON" position to re-arm
the air bag and so guarantee the safety
of your front passenger in the event of
an impact.
With the ignition on, this warn-
ing light comes on on the instru-
ment panel or on the seat belt
and passenger’s front air bag
warning lights display for approximately
one minute, if the passenger’s front air
bag is activated.
To guarantee the safety of your child,
it is imperative that the passenger’s
front air bag is disarmed when you
install a "rearwards-facing" child seat
on the front passenger seat.
Otherwise, the child would risk be-
ing seriously injured or killed if the
air bag were triggered.
According to version, this warn-
ing light comes on either on
the instrument panel or on the
seat belt and passenger’s front
air bag warning lights display when the
ignition is on and until the air bag is re-
armed. I f t h i s w a r n i n g l i g h t fl a s h e s ,
contact a CITROËN dealer.
The passenger’s front air bag
may no longer be triggered in
the event of a serious impact.
Deactivation
Only the passenger’s front air bag can
be disarmed:
with the ignition off , insert the key
in the passenger air bag disarming
switch 1 ,
turn it to the "OFF" position,
then, remove the key keeping the
switch in this position.
Page 112 of 204
i
100
DRIVING
SPEED LIMITER
System which prevents the vehicle from
exceeding the speed programmed by
the driver.
When the programmed speed limit is
reached, pressing the accelerator pedal in
the normal manner no longer has any effect.
The controls of this system are grouped
together on stalk A .
1. Speed limiter mode selection dial
2. Value decrease button
3. Value increase button
4. Speed limiter on/off button The programmed information is grouped
together on the instrument panel dis-
play.
5. Speed limiter on/off indication
6. Speed limiter mode selection indica-
tion
7. Programmed speed value
Steering wheel controls Displays on the instrument
panel
The speed limiter cannot, in any
circumstances, replace the need
to respect speed limits, nor can it
replace the need for vigilance and
responsibility on the part of the
driver.
The speed limiter is
switched on manu-
ally: it requires a programmed speed of
at least 20 mph (30 km/h).
The speed limiter is switched off by
manual operation of the control.
The programmed speed can be ex-
ceeded temporarily by pressing the ac-
c e l e r a t o r fi r m l y .
To return to the programmed speed,
simply slow down to a speed below the
programmed speed.
The programmed speed remains in the
memory when the ignition is switched
off.
Page 114 of 204
i
102
DRIVING
CRUISE CONTROL
System which automatically maintains
the speed of the vehicle at the value
programmed by the driver, without any
action on the accelerator pedal.
The cruise control is switched on
manually: it requires a minimum vehicle
speed of 25 mph (40 km/h) and the en-
gaging of at least 4th gear.
The controls of this system are grouped
together on lever A .
1. Cruise control mode selection dial
2. Speed programming/value decrease
button
3. Speed programming/value increase
button
4. Cruise control off/resume button The programmed information is grouped
together on the instrument panel dis-
play.
5. Cruise control off/resume indication
6. Cruise control mode selection indi-
cation
7. Programmed speed value
Steering wheel controls Displays on the instrument
panel
The cruise control cannot, in any
circumstances, replace the need
to respect speed limits, nor can it
replace the need for vigilance and
responsibility on the part of the
driver.
The cruise control is
switched off manu-
ally or by pressing the brake or clutch
pedal or on triggering of the ESP sys-
tem for safety reasons.
It is possible to exceed the programmed
speed temporarily by pressing the ac-
celerator pedal.
To return to the programmed speed,
simply release the accelerator pedal.
Switching off the ignition cancels any
programmed speed value.
Page 121 of 204
110
CHECKS
CHECKING LEVELS Brake fluid level
Oil level The reading will only be correct
if the vehicle is on level ground
and the engine has been off for
more than 15 minutes.
The check is carried out either when the
ignition is switched on using the oil level
indicator on the instrument panel, or us-
ing the dipstick.
Between two oil changes, the consump-
tion should not exceed 0.5 litre per
600 miles (1,000 km). T h e b r a k e fl u i d l e v e l s h o u l d b e
close to the "MAX" mark. If it is
not, check the brake pad wear.
Draining the circuit
Refer to the Maintenance and Warranty
Guide for details of the interval for this
operation.
Coolant level The coolant level should be
close to the "MAX" mark but
should never exceed it.
When the engine is warm, the
temperature of the coolant is regulated
by the fan. This can operate with the ig-
nition off.
O n v e h i c l e s w h i c h a r e fi t t e d w i t h a
p a r t i c l e e m i s s i o n fi l t e r , t h e f a n m a y
operate after the vehicle has been
s w i t c h e d o f f , e v e n i f t h e e n g i n e i s
cold.
In addition, as the cooling system is
pressurised, wait at least one hour after
switching off the engine before carrying
out any work. F l u i d s p e c i fi c a t i o n
For optimum cleaning and to avoid
f r e e z i n g , t h i s fl u i d m u s t n o t b e t o p p e d
up or replaced with water.
Draining the engine
Refer to the Maintenance and Warranty
Guide for details of the interval for this
operation.
In order to maintain the reliability of the
engine and emission control system,
the use of additives in the engine oil is
prohibited.
O i l s p e c i fi c a t i o n
The oil must correspond to your engine
and conform to the manufacturer’s re-
commendations. F l u i d s p e c i fi c a t i o n
T h e b r a k e fl u i d m u s t c o n f o r m t o t h e
manufacturer’s recommendations and
f u l fi l t h e D O T 4 s t a n d a r d s .
F l u i d s p e c i fi c a t i o n
The coolant must conform to the manu-
facturer’s recommendations.
Draining the circuit
The coolant does not have to be
changed.
Screenwash fluid level
Top up the level when neces-
sary.
Check all of these levels regularly and
top them up if necessary, unless other-
wise indicated.
I f a l e v e l d r o p s s i g n i fi c a n t l y , h a v e t h e
corresponding circuit checked by a
CITROËN dealer.
To avoid any risk of scalding, unscrew
the cap by two turns to allow the pres-
sure to drop. When the pressure has
dropped, remove the cap and top up
the level.
Page 142 of 204
i
!
!
130
PRACTICAL INFORMATION D o n o t d i s c o n n e c t t h e t e r m i n a l s
w h i l e t h e e n g i n e i s r u n n i n g .
D o n o t c h a r g e t h e b a t t e r i e s w i t h o u t
d i s c o n n e c t i n g t h e t e r m i n a l s fi r s t .
The batteries contain harmful sub-
stances such as sulphuric acid and
l e a d . T h e y m u s t b e d i s p o s e d o f i n
accordance with regulations and
must not, in any circumstances, be
d i s c a r d e d w i t h h o u s e h o l d w a s t e .
Take used remote control batteries
and vehicle batteries to a special
c o l l e c t i o n p o i n t .
Charging the battery using a
battery charger
D i s c o n n e c t t h e b a t t e r y f r o m t h e v e -
h i c l e .
Follow the instructions for use pro-
vided by the manufacturer of the
c h a r g e r .
Reconnect starting with the nega-
t i v e t e r m i n a l ( - ) .
Check that the terminals and con-
n e c t o r s a r e c l e a n . I f t h e y a r e c o v -
ered with sulphate (whitish or green-
ish deposit), remove them and clean
t h e m .
At the risk of discharging the bat-
tery, the deactivated functions can
b e r e a c t i v a t e d m a n u a l l y .
LOAD REDUCTION MODE
System which manages the use of cer-
tain functions in relation to the level of
c h a r g e r e m a i n i n g i n t h e b a t t e r y .
When the vehicle is being driven, the
load reduction function temporarily deac-
tivates certain functions, such as the air
c o n d i t i o n i n g , t h e r e a r s c r e e n d e - i c i n g . . .
The deactivated functions are reacti-
vated automatically as soon as condi-
t i o n s p e r m i t .
It is advisable to disconnect the
battery if the vehicle is to be left un-
u s e d f o r m o r e t h a n o n e m o n t h . Before disconnecting the
battery
Wait 2 minutes after switching off
the ignition before disconnecting
t h e b a t t e r y .
Close the windows and the doors
b e f o r e d i s c o n n e c t i n g t h e b a t t e r y .
Following reconnection of the
battery
Following reconnection of the bat-
tery, switch on the ignition and wait
1 minute before starting to permit in-
i t i a l i s a t i o n o f t h e e l e c t r o n i c s y s t e m s .
H o w e v e r , i f s l i g h t d i f fi c u l t i e s a r e e n -
countered following this operation,
c o n t a c t a C I T R O Ë N d e a l e r .
Referring to the corresponding sec-
tion, you must yourself reinitialise:
- the remote control key,
- the GPS satellite navigation
s y s t e m .
Page 143 of 204
i
!
!
130
PRACTICAL INFORMATION D o n o t d i s c o n n e c t t h e t e r m i n a l s
w h i l e t h e e n g i n e i s r u n n i n g .
D o n o t c h a r g e t h e b a t t e r i e s w i t h o u t
d i s c o n n e c t i n g t h e t e r m i n a l s fi r s t .
The batteries contain harmful sub-
stances such as sulphuric acid and
l e a d . T h e y m u s t b e d i s p o s e d o f i n
accordance with regulations and
must not, in any circumstances, be
d i s c a r d e d w i t h h o u s e h o l d w a s t e .
Take used remote control batteries
and vehicle batteries to a special
c o l l e c t i o n p o i n t .
Charging the battery using a
battery charger
D i s c o n n e c t t h e b a t t e r y f r o m t h e v e -
h i c l e .
Follow the instructions for use pro-
vided by the manufacturer of the
c h a r g e r .
Reconnect starting with the nega-
t i v e t e r m i n a l ( - ) .
Check that the terminals and con-
n e c t o r s a r e c l e a n . I f t h e y a r e c o v -
ered with sulphate (whitish or green-
ish deposit), remove them and clean
t h e m .
At the risk of discharging the bat-
tery, the deactivated functions can
b e r e a c t i v a t e d m a n u a l l y .
LOAD REDUCTION MODE
System which manages the use of cer-
tain functions in relation to the level of
c h a r g e r e m a i n i n g i n t h e b a t t e r y .
When the vehicle is being driven, the
load reduction function temporarily deac-
tivates certain functions, such as the air
c o n d i t i o n i n g , t h e r e a r s c r e e n d e - i c i n g . . .
The deactivated functions are reacti-
vated automatically as soon as condi-
t i o n s p e r m i t .
It is advisable to disconnect the
battery if the vehicle is to be left un-
u s e d f o r m o r e t h a n o n e m o n t h . Before disconnecting the
battery
Wait 2 minutes after switching off
the ignition before disconnecting
t h e b a t t e r y .
Close the windows and the doors
b e f o r e d i s c o n n e c t i n g t h e b a t t e r y .
Following reconnection of the
battery
Following reconnection of the bat-
tery, switch on the ignition and wait
1 minute before starting to permit in-
i t i a l i s a t i o n o f t h e e l e c t r o n i c s y s t e m s .
H o w e v e r , i f s l i g h t d i f fi c u l t i e s a r e e n -
countered following this operation,
c o n t a c t a C I T R O Ë N d e a l e r .
Referring to the corresponding sec-
tion, you must yourself reinitialise:
- the remote control key,
- the GPS satellite navigation
s y s t e m .
Page 144 of 204
i
!
131
PRACTICAL INFORMATION
A fl a t b a t t e r y p r e v e n t s t h e e n g i n e
from starting (refer to the corre-
s p o n d i n g p a r a g r a p h ) .
If the telephone is being used at
the same time with the MyWay au-
dio navigation, it will be interrupted
a f t e r 1 0 m i n u t e s .
ENERGY ECONOMY MODE
System which manages the duration of
use of certain functions to conserve a
s u f fi c i e n t l e v e l o f c h a r g e i n t h e b a t t e r y .
After the engine has stopped, you can
still use functions such as the audio
e q u i p m e n t , w i n d s c r e e n w i p e r s , d i p p e d
h e a d l a m p s , c o u r t e s y l i g h t s , e t c . f o r a
maximum combined duration of thirty
m i n u t e s . Exiting economy mode
These functions are reactivated auto-
m a t i c a l l y n e x t t i m e t h e v e h i c l e i s d r i v e n .
In order to resume the use of these
functions immediately, start the en-
g i n e a n d l e t i t r u n f o r a f e w m i n u t e s .
The time available to you will then be
double the duration for which the en-
g i n e i s l e f t r u n n i n g . H o w e v e r , t h i s p e r i o d
w i l l a l w a y s b e b e t w e e n fi v e a n d t h i r t y
m i n u t e s .
Switching to economy mode
Once the thirty minutes are over, a
message appears on the multifunction
display indicating that the vehicle has
switched to economy mode and the ac-
t i v e f u n c t i o n s a r e p u t o n s t a n d b y .
CHANGING A WIPER BLADE
Procedure for replacing a worn wiper
blade with a new one without the use
o f t o o l s .
Removing a front or rear wiper
blade
R a i s e t h e c o r r e s p o n d i n g w i p e r a r m .
U n c l i p t h e w i p e r b l a d e a n d r e m o v e i t .
Fitting a front or rear wiper blade
At the front, check the size of the
wiper blade as the shorter blade is
fi t t e d o n t h e r i g h t - h a n d s i d e o f t h e
v e h i c l e .
Put the corresponding new wiper
b l a d e i n p l a c e a n d c l i p i t .
F o l d d o w n t h e w i p e r a r m c a r e f u l l y .
Before removing a front wiper blade
Within one minute after switching off
the ignition, operate the wipers stalk
to position the wiper blades in the
v e r t i c a l p o s i t i o n .
This position must be used in order to
avoid damaging the wiper blade and the
b o n n e t .
After fitting a front wiper blade
S w i t c h o n t h e i g n i t i o n .
Operate the wipers stalk again to
p a r k t h e w i p e r b l a d e s .
Page 200 of 204
1
11
11
22
33
USB PLAYER
The system puts together playlists (temporary memory) created over a period which depends on the capacity of the USB e quipment. The other sources are available during this time. The playlists are updated each time the ignition is switched off or each time a USB stick is connected. W h e n c o n n e c t i n g f o r t h e fi r s t t i m e , t h e t r a c k s a r e c l a s s i fi e d b y f o l d e r . W h e n y o u r e c o n n e c t , t h e c l a s s i fi c a t i o n s y s t e m s e l e c t e d p r e v i o u s l y i s retained.
C o n n e c t t h e s t i c k t o t h e p o r t , d i r e c t l y or using a lead. If the audio equipment i s s w i t c h e d o n , t h e U S B s o u r c e i s detected as soon as it is connected. Play begins automatically after a delay which depends on the capacity of the USB stick. T h e fi l e f o r m a t s r e c o g n i s e d a r e . m p 3 ( m p e g 1 l a y e r 3 o n l y ) , . w m a ( s t a n d a r d 9 o n l y ) , . w a v a n d . o g g .
This unit consists of a USB port and a J a c k s o c k e t . I t r e a d s a u d i o fi l e f o r m a t s ( . m p 3 , . o g g , . w m a , . w a v . . . ) w h i c h a r e transmitted from portable equipment such as a digital player or a USB stick to y o u r a u d i o s y s t e m , t o b e l i s t e n e d t o v i a the vehicle's speakers.
U S B s t i c k ( 1 . 1 , 1 . 2 a n d 2 . 0 ) o r I p o d ® of ®
generation 5 or later: - the playlists accepted are of the type m 3 u , . p l s , . w p l . , - the Ipod ® l e a d i s e s s e n t i a l , ®
- n a v i g a t i o n t h r o u g h t h e fi l e b a s e i s b y m e a n s o f t h e s t e e r i n g w h e e l c o n t r o l s , - the battery of the portable equipment can charge automatically.
Other Ipod ® players of earlier generations ®
and players using the MTP protocol: - play via Jack-Jack lead only ( n o t s u p p l i e d ) , - n a v i g a t i o n t h r o u g h t h e fi l e b a s e i s f r o m the portable equipment.
The list of compatible equipment is available from dealers. USING THE USB PORT
CONNECTING A USB STICK