2008.5 Citroen BERLINGO MULTISPACE service
[x] Cancel search: servicePage 20 of 161
24
Accesses
CENTRAL LOCKING
An initial press permits
central locking of the vehicle,
when all of the doors are
closed.
A second press permits
central unlocking of the vehicle.
The control is inactive when the vehicle
has been locked using the remote
control or the key from the outside.
The doors can still be opened from the
inside.
Door open warning light
The control diode:
- fl a s h e s w h e n t h e d o o r s a r e l o c k e d
with the vehicle stationary and the
engine off,
- comes on when the doors are locked and from the time the
ignition is switched on. Protection against attack
If this warning light comes on,
check that all of your vehicle’s
doors are closed correctly.
Locking while driving
When the vehicle moves off, as soon
a s y o u r e a c h a p p r o x i m a t e l y 6 m p h
(10 km/h),
the system locks the doors. A noise
characteristic of central locking is
heard. The diode on the control on the
fascia central control panel comes on.
During the journey, opening a door
results in complete unlocking of the
vehicle.
In the event of a serious impact, the
doors are unlocked automatically
to permit access by the emergency
services.
Activating/deactivating the function
With the ignition on, press
and hold this button to
activate or deactivate the
function.
Page 21 of 161
READY TO SET OFF
25 25
22
Instruments and controls
INSTRUMENT PANEL Displays
INSTRUMENTS AND CONTROLS Screens
The information is presented on board
the vehicle in different display formats
according to the vehicle’s equipment.
Dials
1. Distance recorder in kilometres/
miles.
2. Display.
3. Fuel level, coolant temperature.
4. Rev counter.
5. Trip distance recorder/service
indicator zero reset.
6. Instrument panel lighting rheostat. - Speed limiter/cruise control.
- Kilometres/Miles travelled.
- Service indicator, engine oil level
indicator, total kilometres/miles.
- Presence of water in the diesel fi l t e r .
- Diesel pre-heating.
Page 24 of 161
28
Instruments and controls
Warning light is indicates Solution - action
Coolant
temperature
and level lit with needle
in the red
zone.
an abnormal increase in
temperature.
Park and switch off the ignition then allow to cool.
Visually check the level.
fl a s h i n g . a drop in the coolant level. Chapter 7, "Levels" section. Consult a CITROËN
dealer.
Service lit temporarily. minor faults or warnings.
Consult the warnings log on the display or on
the screen. If your vehicle is equipped with a
trip computer or a screen: refer to the "Audio
equipment - Trip computer" section of chapter 4.
Consult a CITROËN dealer.
remaining on. major faults.
Driver’s
seat belt not
fastened lit then
fl a s h i n g .
the driver has not fastened
his seat belt.
Pull the strap then insert the tongue in the buckle.
accompanied
by an audible
signal then
remains on. the vehicle is moving with
the driver’s seat belt not
fastened.
Check that the seat belt is fastened by pulling the
strap. Chapter 5, "Seat belts" section.
Page 28 of 161
Instruments and controls
Warning light on
the display
is indicates Solution - action
Cruise
control lit. cruise control selected. Manual selection. Chapter 3, "Steering wheel
controls" section.
Speed limiter lit. speed limiter selected. Manual selection. Chapter 3, "Steering wheel
controls" section.
Diesel
pre-heating lit. climatic conditions requiring
pre-heating. Wait until the warning light is switched off before
operating the starter.
Presence of
water in the
d i e s e l fi l t e r
lit and
accompanied by
a message on
the display.
w a t e r i n t h e d i e s e l fi l t e r . H a v e t h e fi l t e r b l e d b y a C I T R O Ë N d e a l e r w i t h o u t
delay. Chapter 7, "Checks" section.
According to country.
Service
spanner lit. that a service will be due
shortly. Refer to the list of checks in the servicing booklet.
Have the service carried out by a CITROËN
dealer.
Time fl a s h i n g . adjustment of the time. Use the left-hand button on the instrument panel.
Chapter 2, at the beginning of the "Instruments
and controls" section.
Page 31 of 161
READY TO SET OFF
35 35
22
Instruments and controls
SERVICE INDICATOR
This programmes service intervals
according to the use of the vehicle. More than 1 000 miles/km before the
next service is due
Example: 4 800 miles/km remain
b e f o r e t h e n e x t s e r v i c e i s d u e . W h e n
the ignition is switched on and for a
few seconds, the display shows:
A few seconds after the ignition is
switched on, the oil level is displayed,
then the total distance recorder
resumes normal operation showing the
total and trip distances.
Less than 1 000 miles/km before the
next service is due
Each time the ignition is switched on
and for a few seconds, the spanner
fl a s h e s a n d t h e n u m b e r o f m i l e s /
kilometres remaining is displayed: A few seconds after the ignition is
switched on, the oil level is displayed,
then the total distance recorder
resumes normal operation and the
spanner remains lit. This indicates that
a service should be carried out shortly.
Service overdue
First of the two terms reached: the
spanner also lights up if the two-year
interval has elapsed.
Operation
A few moments after the ignition
has been switched on, the spanner
indicating a service operation lights
up; the display for the total distance
r e c o r d e r t e l l s y o u ( i n r o u n d fi g u r e s )
t h e d i s t a n c e r e m a i n i n g b e f o r e t h e n e x t
service.
The points at which a service is due
are calculated from the last indicator
zero reset.
The point at which a service is due is
determined by two parameters:
- the distance travelled,
- the time which has elapsed since
the last service.
The distance remaining before the
n e x t s e r v i c e m a y b e w e i g h t e d b y
the time factor, depending on the
driver’s driving habits. With the engine running the
spanner remains lit until the
service has been carried out.
Each time the ignition is
switched on and for a few
seconds, the spanner
fl a s h e s a n d t h e e x c e s s
distance is displayed.
Page 32 of 161
36
Instruments and controls Trip recorder zero reset button
After this operation, if you wish to
disconnect the battery, lock the
v e h i c l e a n d w a i t f o r a t l e a s t fi v e
minutes, otherwise the zero re-set will
not be registered.
Zero re-set
Your CITROËN dealer carries out this
operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
- switch off the ignition,
- press and hold the trip recorder
reset button,
- switch on the ignition.
The display begins a countdown.
When the display shows "=0" , release
the button; the spanner disappears.
Engine oil level indicator
When the ignition is switched on, the
engine oil level is indicated for a few
seconds, after the service information. Oil level correct
Lack of oil
Flashing of
"OIL" ,
linked with the
service warning light,
accompanied by an
audible signal and a message on the
display, indicates a lack of oil which
could damage the engine.
I f t h e l a c k o f o i l i s c o n fi r m e d b y a c h e c k
using the dipstick, it is essential that
the level is topped up.
Oil level gauge fault
Flashing of "OIL --"
indicates a malfunction
of the engine oil level
gauge. Consult a
CITROËN dealer.
The level read will only be correct
if the vehicle is on level ground
and the engine has been off for
more than 15 minutes. Dipstick
A = m a x i m u m , n e v e r e x c e e d
this level as a surplus of oil
may damage the engine.
Contact a CITROËN dealer
without delay.
B = minimum, top up the level
v i a t h e o i l fi l l e r c a p , u s i n g
the type of oil suited to your
engine.
Lighting rheostat With the ignition on, press
the button until the zeros
appear.
With the lights on, press
the button to vary the
intensity of the lighting
of the instruments and
controls. When the lighting
reaches the minimum (or
m a x i m u m ) s e t t i n g , r e l e a s e
the button then press it again to
increase (or reduce) the brightness.
As soon as the lighting is of the
required brightness, release the button.
Page 93 of 161
9 4
1 1
2 2
33
1 1
2 2
5 5 1 1
0 4 HANDS-FREE KIT
F o r s a f e t y r e a s o n s a n d b e c a u s e t h e y r e q u i r e p r o l o n g e d a t t e n t i o n o n t h e p a r t o f t h e d r i v e r , t h e o p e r a t i o n s f o r m a t c h i n g o f t h e B l u e t o o t h mobile telephone with the audio equipment hands-fre e kit must be c a r r i e d o u t w i t h t h e v e h i c l e s t a t i o n a r y a n d t h e i g n i t i o n o n .
Select the accessory which corresponds to the n a m e o f t h e v e h i c l e , a s u p e r i m p o s e d c o n fi g u r a t i o n display appears on the multifunction display.
Activate the telephone’s Bluetooth function and carry out a search of the Bluetooth accessories present for the telephone.
S e l e c t t h e Y E S t a b o n t h e d i s p l a y u s i n g t h e b u t t o n s t h e n c o n fi r m b y p r e s s i n g O K .
E n t e r t h e v e h i c l e ’ s a u t h e n t i c a t i o n c o d e ( = 1 2 3 4 ) . D e p e n d i n g o n t h e t e l e p h o n e , y o u m a y b e a s k e d to enter this code before the superimposed c o n fi g u r a t i o n d i s p l a y a p p e a r s .
YES
YES
The services offered by the hands-free kit depend on the network, the SIM card and the compatibility of the Bluetooth equipment used. C o n s u l t y o u r t e l e p h o n e ’ s m a n u a l a n d y o u r o p e r a t o r t o fi n d o u t w h i c h s e r v i c e s a r e a v a i l a b l e t o y o u . A l i s t o f m o b i l e t e l e p h o n e s w h i c h o f f e r t h e b e s t r a n g e o f s e r v i c e s i s available from the network. Consult a CITROËN deal er. Refer to the end of the "Correct use of the hands-free kit telephone" section.
RECEIVING A CALL
A n i n c o m i n g c a l l i s a n n o u n c e d b y a r i n g a n d a s u p e r i m p o s e d d i s p l a y on the multifunction display.
S e l e c t t h e Y E S t a b o n t h e d i s p l a y u s i n g t h e b u t t o n s a n d c o n fi r m b y p r e s s i n g O K .
P r e s s t h e e n d o f t h e s t e e r i n g w h e e l s t a l k t o a c c e p t the call.
P r e s s t h e e n d o f t h e s t e e r i n g w h e e l s t a l k f o r m o r e than two seconds to access your directory.
To dial a number, use the keypad on your telephone.
MAKING A CALL
MATCHING A TELEPHONE
DISPLAY C
Page 100 of 161
1
1
2
3
4
3
4
3
4
2
3
4
3
4
2
3
4
2
4
4
3
4
4
4
3
4
4
1
2
3
2
3
3
2
2
1
2
3
3
3
4
4
4
2
3
4
3
4
3
4
2
3
3
3
4
0 8 1 0 1
PERSONALISATION-CONFIGURATION
AUDIO FUNCTIONS
DISPLAY C FLOW CHART
* T h e p a r a m e t e r s v a r y a c c o r d i n g t o v e h i c l e .
* * A c c o r d i n g t o c o m p a t i b i l i t y o f B l u e t o o t h t e l e p h o n e and service contract.
TELEPHONE
STATUS OF FUNCTIONS *
f u n c t i o n s a c t i v a t e d o r d e a c t i v a t e d
TRIP COMPUTER
FM BAND PREFERENCES
a l t e r n a t i v e f r e q u e n c i e s ( R D S )
activate/deactivate
r e g i o n a l m o d e ( R E G )
activate/deactivate
r a d i o - t e x t i n f o r m a t i o n ( R D T X T )
activate/deactivate
AUDIO CD PREFERENCES
CD c h a n g e r r e p e a t ( R P T )
activate/deactivate
t r a c k r a n d o m p l a y ( R D M )
activate/deactivate
ENTER DISTANCE TO DESTINATION
d i s t a n c e : x k m
WARNING LOG
d i a g n o s t i c s
DEFINE THE VEHICLE PARAMETERS *
DISPLAY CONFIGURATION
v i d e o b r i g h t n e s s a d j u s t m e n t
normal video
inverse video
b r i g h t n e s s ( - + ) a d j u s t m e n t
d a t e a n d t i m e a d j u s t m e n t
day/month/year adjustment
hour/minute adjustment
c h o i c e o f 1 2 h / 2 4 h m o d e
c h o i c e o f u n i t s
l / 1 0 0 k m - m p g - k m / l
° C e l s i u s / ° F a h r e n h e i t
CHOICE OF LANGUAGE
CONSULTING DIRECTORIES **
t e l e p h o n e d i r e c t o r y
c a l l l o g
s e r v i c e s d i r e c t o r y
customer contact centre
breakdown call
e m e r g e n c y c a l l
CONFIGURATION
d e l e t i o n o f a m a t c h
list of matches
c o n s u l t i n g m a t c h e s
list of matches
c h o i c e o f a m o b i l e t o c o n n e c t
list of mobiles
MANAGEMENT OF A COMMUNICATION
s w i t c h
t e r m i n a t e t h e c u r r e n t c a l l
s e c r e t m o d e
activate/deactivate