2008.5 Citroen BERLINGO MULTISPACE engine
[x] Cancel search: enginePage 32 of 161
36
Instruments and controls Trip recorder zero reset button
After this operation, if you wish to
disconnect the battery, lock the
v e h i c l e a n d w a i t f o r a t l e a s t fi v e
minutes, otherwise the zero re-set will
not be registered.
Zero re-set
Your CITROËN dealer carries out this
operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
- switch off the ignition,
- press and hold the trip recorder
reset button,
- switch on the ignition.
The display begins a countdown.
When the display shows "=0" , release
the button; the spanner disappears.
Engine oil level indicator
When the ignition is switched on, the
engine oil level is indicated for a few
seconds, after the service information. Oil level correct
Lack of oil
Flashing of
"OIL" ,
linked with the
service warning light,
accompanied by an
audible signal and a message on the
display, indicates a lack of oil which
could damage the engine.
I f t h e l a c k o f o i l i s c o n fi r m e d b y a c h e c k
using the dipstick, it is essential that
the level is topped up.
Oil level gauge fault
Flashing of "OIL --"
indicates a malfunction
of the engine oil level
gauge. Consult a
CITROËN dealer.
The level read will only be correct
if the vehicle is on level ground
and the engine has been off for
more than 15 minutes. Dipstick
A = m a x i m u m , n e v e r e x c e e d
this level as a surplus of oil
may damage the engine.
Contact a CITROËN dealer
without delay.
B = minimum, top up the level
v i a t h e o i l fi l l e r c a p , u s i n g
the type of oil suited to your
engine.
Lighting rheostat With the ignition on, press
the button until the zeros
appear.
With the lights on, press
the button to vary the
intensity of the lighting
of the instruments and
controls. When the lighting
reaches the minimum (or
m a x i m u m ) s e t t i n g , r e l e a s e
the button then press it again to
increase (or reduce) the brightness.
As soon as the lighting is of the
required brightness, release the button.
Page 34 of 161
Starting and stopping Good practice when stopping
Good practice when starting
Diesel pre-heating warning
light
If the temperature is high
enough, the warning light
comes on for less than one
second, you can start without
waiting.
In cold weather, wait for this warning
light to switch off then operate the
starter (Starting position) until the
engine starts. Door or bonnet open
warning light
If this comes on, a door or
the bonnet is not closed
correctly, check!
Minimise engine and gearbox wear
When switching off the ignition, let the
engine run for a few seconds to allow
the turbocharger (Diesel engine) to
return to idle.
Do not press the accelerator when
switching off the ignition.
There is no need to engage a gear
after parking the vehicle.
STARTING AND STOPPING
Running and accessories position.
To unlock the steering, turn the
steering wheel gently while turning the
key, without forcing. In this position,
certain accessories can be used.
Starting position.
The starter is operated, the engine
turns over, release the key.
STOP position: steering lock.
The ignition is off. Turn the steering
wheel until the steering locks. Remove
the key.
Page 35 of 161
39
READY TO SET OFF
39
22
Starting and stopping
This function, linked with the ESP,
makes hill starts easier and is activated
in the following conditions:
- the vehicle must be stationary, engine running, foot on the brake,
- the gradient of the road must be steeper than 5 %,
- u p h i l l , t h e g e a r b o x m u s t b e i n neutral or in a gear other than
reverse,
- downhill, reverse gear must be engaged. Operation
With the brake pedal and clutch pedal
pressed, from the time you release the
b r a k e p e d a l y o u h a v e a p p r o x i m a t e l y
2 seconds before the vehicle starts
to roll back and without using the
handbrake within which to move off.
During the moving off phase, the
function is deactivated automatically,
gradually releasing the braking
pressure. During this phase, the typical
noise of mechanical disengaging of
the brakes can be heard, indicating the
imminent movement of the vehicle.
Anomaly
The hill start assistance is deactivated
in the following situations:
- when the clutch pedal is released,
- when the handbrake is applied,
- when the engine is switched off,
- when the engine stalls.
If a malfunction of the
system occurs, this warning
light comes on accompanied
by an audible signal and
c o n fi r m e d b y a m e s s a g e
on the display. Contact a CITROËN
dealer to have the system checked.
HILL START ASSISTANCE
Page 46 of 161
4 8
Steering wheel controls H o w e v e r , p r e s s i n g t h e p e d a l b e y o n d
t h i s p o i n t o f r e s i s t a n c e t o t h e fl o o r
p e r m i t s e x c e e d i n g o f t h e p r o g r a m m e d
s p e e d . T o r e s u m e u s e o f t h e l i m i t e r ,
simply reduce the pressure on the
a c c e l e r a t o r p e d a l g r a d u a l l y a n d r e t u r n
t o a s p e e d b e l o w t h a t p r o g r a m m e d .
The operating actions may be
carried out when stationary, with the
engine running, or with the vehicle
moving. T h i s s p e e d l i m i t e r s h o w s t h e f u n c t i o n
s e l e c t i o n s t a t u s o n t h e i n s t r u m e n t
p a n e l a n d d i s p l a y s t h e p r o g r a m m e d
s p e e d :
SPEED LIMITER "LIMIT"
Function selected,
d i s p l a y i n g o f t h e
"Speed Limiter"
symbol.
F u n c t i o n d e a c t i v a t e d ,
l a s t p r o g r a m m e d
speed -
OFF
( e x a m p l e a t 6 5 m p h
( 1 0 7 k m / h ) ) .
F u n c t i o n a c t i v a t e d
( e x a m p l e a t 6 5 m p h
( 1 0 7 k m / h ) ) .
V e h i c l e s p e e d a b o v e
( e x a m p l e 7 0 m p h
( 1 1 8 k m / h ) ) , t h e
p r o g r a m m e d s p e e d i s
d i s p l a y e d fl a s h i n g .
O p e r a t i n g f a u l t
detected,
OFF - t h e d a s h e s
fl a s h .
" T h i s i s t h e s e l e c t e d s p e e d w h i c h t h e
d r i v e r d o e s n o t w i s h t o e x c e e d " .
T h i s s e l e c t i o n i s m a d e w i t h t h e e n g i n e
r u n n i n g w h i l e s t a t i o n a r y o r w i t h t h e
v e h i c l e m o v i n g . T h e m i n i m u m s p e e d
w h i c h c a n b e p r o g r a m m e d i s 2 0 m p h
( 3 0 k m / h ) .
T h e s p e e d o f t h e v e h i c l e r e s p o n d s
t o t h e p r e s s u r e o f t h e d r i v e r ’ s f o o t a s
f a r a s t h e a c c e l e r a t o r p e d a l p o i n t o f
r e s i s t a n c e w h i c h i n d i c a t e s t h a t t h e
p r o g r a m m e d s p e e d h a s b e e n r e a c h e d .
Page 47 of 161
49
Steering wheel controls
3
Selecting the function
- P l a c e t h e d i a l i n t h e LIMIT position.
T h e l i m i t e r i s s e l e c t e d b u t i s n o t y e t
a c t i v e . T h e d i s p l a y i n d i c a t e s t h e
l a s t p r o g r a m m e d s p e e d .
Programming a speed
A s p e e d c a n b e p r o g r a m m e d w i t h o u t
a c t i v a t i n g t h e l i m i t e r b u t w i t h t h e
engine running.
T o m e m o r i s e a s p e e d h i g h e r t h a n t h e
p r e v i o u s o n e :
- press the Set + button.
A b r i e f p r e s s i n c r e a s e s t h e s p e e d b y
1 m p h ( k m / h ) .
A m a i n t a i n e d p r e s s i n c r e a s e s t h e
s p e e d i n s t e p s o f 5 m p h ( k m / h ) .
T o m e m o r i s e a s p e e d l o w e r t h a n t h e
p r e v i o u s o n e :
- press the Set - button.
A b r i e f p r e s s d e c r e a s e s t h e s p e e d b y
1 m p h ( k m / h ) .
A m a i n t a i n e d p r e s s d e c r e a s e s t h e
s p e e d i n s t e p s o f 5 m p h ( k m / h ) . Activation/Deactivation (off)
P r e s s i n g t h i s b u t t o n o n c e a c t i v a t e s
t h e l i m i t e r , p r e s s i n g t h e b u t t o n a g a i n
d e a c t i v a t e s i t ( O F F ) .
Page 50 of 161
5 2
Ventilation
Intake of exterior air
Recirculation of interior air Air conditioning A/C
T h e d i o d e o n t h e b u t t o n
i s o f f . T h i s i s t h e p r e f e r r e d
o p e r a t i n g p o s i t i o n . Pressing the button triggers
t h e o p e r a t i o n o f t h e a i r
conditioning, the diode is lit.
P r e s s i n g t h e b u t t o n a g a i n
s w i t c h e s t h e f u n c t i o n o f f a n d
the diode is switched off.
T h e a i r c o n d i t i o n i n g d o e s n o t o p e r a t e i f
t h e a i r fl o w i s s e t t o 0 .
T h e a i r c o n d i t i o n i n g c a n o n l y o p e r a t e
with the engine running.
T h e d i o d e o n t h e b u t t o n i s
l i t . R e c i r c u l a t i o n t e m p o r a r i l y
p r e v e n t s e x t e r i o r o d o u r s
a n d s m o k e f r o m e n t e r i n g t h e
p a s s e n g e r c o m p a r t m e n t .
Used with the setting of the force of
b l o w n a i r ( f r o m 1 t o 4 ) , r e c i r c u l a t i o n
e n a b l e s y o u t o o b t a i n t h e r e q u i r e d
a m b i e n t a i r c o m f o r t l e v e l m o r e q u i c k l y
with both hot or cold settings.
T h i s p o s i t i o n s h o u l d o n l y b e t e m p o r a r y .
W h e n y o u r a m b i e n t a i r c o m f o r t l e v e l
h a s b e e n r e a c h e d , r e t u r n t o t h e
i n t a k e o f e x t e r i o r a i r p o s i t i o n t o p e r m i t
r e n e w a l o f t h e a i r i n t h e p a s s e n g e r
c o m p a r t m e n t a n d a v o i d m i s t i n g . T h i s
o p e r a t i n g m o d e i s p r e f e r a b l e .
Page 51 of 161
Ventilation
55
ERGONOMICS and COMFORT
33
DE-ICING AND DEMISTING
Manual mode Direct the control to this
t e m p e r a t u r e s e t t i n g .
I n c r e a s e t h e a i r fl o w s e t t i n g . P r e s s t h e a i r c o n d i t i o n i n g .
R e t u r n i n g t o e x t e r i o r a i r
i n t a k e o p e n p e r m i t s r e n e w a l
o f t h e a i r i n t h e p a s s e n g e r
c o m p a r t m e n t ( d i o d e o f f ) .
D i r e c t t h e c o n t r o l t o t h i s a i r
distribution setting.
De-icing the rear screen and/or
mirrors
Pressing this button, with the
e n g i n e r u n n i n g , a c t i v a t e s t h e
r a p i d d e m i s t i n g - d e - i c i n g o f
t h e r e a r s c r e e n a n d / o r e l e c t r i c
mirrors.
T h i s f u n c t i o n s w i t c h e s o f f :
- when the button is pressed,
- when the engine is switched off,
- a u t o m a t i c a l l y t o p r e v e n t e x c e s s i v e energy consumption.
Page 104 of 161
105
Driving safety
SAFETY
5
TRACTION CONTROL (ASR)
AND DYNAMIC STABILITY
CONTROL (ESP)
These systems are linked and
complement the ABS.
The ASR system is very useful for
maintaining optimum drive and
avoiding losses of control of the vehicle
on acceleration.
The system optimises drive to prevent
the wheels skidding, by acting on the
brakes of the drive wheels and on the
engine. It also allows the directional
stability of the vehicle to be improved
on acceleration.
Use the ESP to hold your course
without attempting to countersteer.
If there is a variation between the
trajectory followed by the vehicle and
that required by the driver, the ESP
system automatically acts on the
engine and the brake of one or more
wheels, in order to put the vehicle back
on course. Disarming the ASR/ESP
systems
In certain exceptional conditions
(starting the vehicle when stuck in mud
or snow, or on loose ground...), it could
prove useful to disarm the ASR and
ESP systems to make the wheels spin
and regain grip.
- Press the button, located on the
centre console.
- The indicator light comes on: the ASR and ESP systems no longer
act. Operating check
Good practice
The ASR/ESP systems offer increased
safety during normal driving, but
should not incite the driver to take risks
or to drive at high speed.
The operation of these systems is
ensured if the recommendations
of the manufacturer regarding
the wheels (tyres and rims), the
braking components, the electronic
c o m p o n e n t s a n d t h e fi t t i n g a n d r e p a i r
procedures within the CITROËN
network are observed.
After an impact, have these systems
checked by a CITROËN dealer.
Operation of the ASR and ESP
systems
T h e l u m i n o u s d i o d e fl a s h e s
when the ASR or ESP is
triggered.
They engage again:
- automatically above 30 mph (50 km/h),
- manually by pressing the button again. When a malfunction of the
systems occurs, the indicator
light comes on, accompanied
by an audible signal and a
message on the display.
Contact a CITROËN dealer to have the
system checked.
The warning light may also come on if
t h e t y r e s a r e u n d e r - i n fl a t e d . C h e c k t h e
pressure of each tyre.