2007 YAMAHA YZ125LC engine

8. Install:
9Segment 1
9Bolt (segment) 2
NOTE:
9When installing the segment onto the shift cam
3, align the punch mark awith the dowel pin
b.
9Turn the segment clockwise until it stops and
tighten the bolt.
cC
If the segment gets an impact, it may be
damaged. Take care not to give an impact
to the segment when tightening the bolt.
9. Remove:
9Sealant
Forced out on the cylinder mating surface.
10. Apply:
9Engine oil
To the crank pin, bearing, oil delivery hole
and connecting rod big end washer.
11. Check:
9Crankshaft and transmission operation
Unsmooth operation Repair.
NOTE:
If the crankshaft will not turn smoothly, make an
adjustment by gently tapping its right end with a
soft hammer.
4-68
ENGCRANKCASE AND CRANKSHAFT
30 Nm (3.0 m•kg, 22 ft•lb)
1C3-9-32-4D 5/1/06 10:41 AM Page 26

4-69
ENGTRANSMISSION, SHIFT CAM AND SHIFT FORK
Extent of removal Order Part name Q’ty Remarks
TRANSMISSION, SHIFT CAM AND
SHIFT FORK REMOVAL
Preparation for EngineRefer to “ENGINE REMOVAL” section.
removal Separate the crankcase. Refer to“CRANKCASE AND CRANK
SHAFT
” section.
1 Guide bar (long) 1
2 Guide bar (short) 1
3 Shift cam 1
4 Shift fork 3 1
5 Shift fork 1 1
6 Shift fork 2 1
7 Main axle 1
8 Drive axle 1Refer to “REMOVAL POINTS”.
9 Spacer 1
EC4H0000
TRANSMISSION, SHIFT CAM AND SHIFT FORK
Extent of removal:1Shift cam and shift fork removal2Main axle and drive axle removal
1
2



10 Nm (1.0 m•kg, 7.2 ft•lb)
10 Nm (1.0 m•kg, 7.2 ft•lb)
1C3-9-32-4D 5/1/06 10:41 AM Page 28

5-1
CHASFRONT WHEEL AND REAR WHEEL
Extent of removal Order Part name Q’ty Remarks
FRONT WHEEL REMOVAL
Preparation for
Hold the machine by placing the
removalsuitable stand under the engine.
1 Bolt (axle holder) 4 Only loosening.
2 Nut (front wheel axle) 1
3 Front wheel axle 1
4 Front wheel 1
5 Collar 2
6 Oil seal 2
7 Bearing 2 Refer to “REMOVAL POINTS”.
8 Brake disc 1
EC500000
CHASSISEC590000
FRONT WHEEL AND REAR WHEELEC598000
FRONT WHEEL
2
13
3
Extent of removal:1Front wheel removal2Wheel bearing removal3Brake disc removal
w
Support the machine securely so there is no dan-
ger of it falling over.
21 Nm (2.1 m•kg, 15 ft•lb)
21 Nm (2.1 m•kg, 15 ft•lb)
105 Nm (10.5 m•kg, 75 ft•lb)
12 Nm (1.2 m•kg, 8.7 ft•lb)
1C3-9-32-5A 4/7/06 2:44 PM Page 2

5-2
CHASFRONT WHEEL AND REAR WHEEL
EC598100
REAR WHEEL
Extent of removal:1Rear wheel removal2Wheel bearing removal3Brake disc removal
Extent of removal Order Part name Q’ty Remarks
REAR WHEEL REMOVAL
Preparation for
Hold the machine by placing the
removalsuitable stand under the engine.
1 Nut (rear wheel axle) 1
2 Rear wheel axle 1
3 Chain puller 2
4 Rear wheel 1 Refer to “REMOVAL POINTS”.
5 Collar 2
6 Driven sprocket 1
7 Oil seal 2
8 Circlip 1
9 Bearing 2 Refer to “REMOVAL POINTS”.
10 Brake disc 1
2
13
3
w
Support the machine securely so there is no dan-
ger of it falling over.
125 Nm (12.5 m•kg, 90 ft•lb)14 Nm (1.4 m•kg, 10 ft•lb)
19 Nm (1.9 m•kg, 13 ft•lb)
19 Nm (1.9 m•kg, 13 ft•lb)
42 Nm (4.2 m•kg, 30 ft•lb)
1C3-9-32-5A 4/7/06 2:44 PM Page 4

5-10
CHASFRONT BRAKE AND REAR BRAKE
Extent of removal Order Part name Q’ty Remarks
FRONT BRAKE REMOVAL
Preparation for
Hold the machine by placing the
removalsuitable stand under the engine.
Drain the brake fluid. Refer to “REMOVAL POINTS”.
1 Brake hose holder (protector) 2
2 Brake hose holder (caliper) 1
3 Union bolt 2
4 Brake hose 1
5 Pad pin plug 1
Remove when loosening the pad pin.
6 Pad pin 1Loosen when disassembling the caliper.
7 Caliper 1
8 Brake lever 1
9 Master cylinder bracket 1
10 Master cylinder 1
EC5A0000
FRONT BRAKE AND REAR BRAKEEC5A8000
FRONT BRAKE
Extent of removal:1Brake hose removal2Caliper removal3Master cyilinder removal
w
Support the machine securely so there is no dan-
ger of it falling over.
2
1
3
3
9 Nm (0.9 m•kg, 6.5 ft•lb)
6 Nm (0.6 m•kg, 4.3 ft•lb)
6 Nm (0.6 m•kg, 4.3 ft•lb)
10 Nm (1.0 m•kg, 7.2 ft•lb)
3 Nm (0.3 m•kg, 2.2 ft•lb)
18 Nm (1.8 m•kg, 13 ft•lb)
23 Nm (2.3 m•kg, 17 ft•lb)
7 Nm (0.7 m•kg, 5.1 ft•lb)
2
6 Nm (0.6 m•kg, 4.3 ft•lb)
30 Nm (3.0 m•kg, 22 ft•lb)
30 Nm (3.0 m•kg, 22 ft•lb)
1C3-9-32-5A 4/7/06 2:45 PM Page 20

5-11
CHASFRONT BRAKE AND REAR BRAKE
EC5A8100
REAR BRAKE
Extent of removal Order Part name Q’ty Remarks
REAR BRAKE REMOVAL
Preparation for
Hold the machine by placing the
removalsuitable stand under the engine.
Rear wheel Refer to “FRONT WHEEL AND
REAR WHEEL” section.
Drain the brake fluid. Refer to “REMOVAL POINTS”.
1 Brake pedal 1
2 Master cylinder 1
3 Brake hose holder 2
4 Union bolt 2
5 Brake hose 1
6 Pad pin plug 1
Remove when loosening the pad pin.
7 Pad pin 1Loosen when disassembling the caliper.
8 Caliper 1
Extent of removal:1Master cylinder removal2Brake hose removal3Caliper removal
w
Support the machine securely so there is no dan-
ger of it falling over.
2
3
31
1
2 Nm (0.2 m•kg, 1.4 ft•lb)
30 Nm (3.0 m•kg, 22 ft•lb)
30 Nm (3.0 m•kg, 22 ft•lb)
3 Nm (0.3 m•kg, 2.2 ft•lb)
18 Nm (1.8 m•kg, 13 ft•lb)
6 Nm (0.6 m•kg, 4.3 ft•lb)
26 Nm (2.6 m•kg, 19 ft•lb)
10 Nm (1.0 m•kg, 7.2 ft•lb)
10 Nm (1.0 m•kg, 7.2 ft•lb)
1C3-9-32-5A 4/7/06 2:45 PM Page 22

Extent of removal Order Part name Q’ty Remarks
FRONT FORK REMOVAL
Preparation for
Hold the machine by placing the
removalsuitable stand under the engine.
Front wheel Refer to “FRONT WHEEL AND
REAR WHEEL”section.
Front caliper Refer to “FRONT BRAKE AND
REAR BRAKE”section.
Number plate
Refer to “SEAT, FUEL TANK AND SIDE
COVERS” section in the CHAPTER 4.
1 Protector 1
2 Pinch bolt (handle crown) 2 Only loosening.
3 Damper assembly 1
Loosen when disassembling the front fork.
Use special tool. Refer to “REMOVAL POINTS”.
4 Pinch bolt (under bracket) 2 Only loosening.
5 Front fork 1
5-26
CHASFRONT FORK
1
w
Support the machine securely so there is no dan-
ger of it falling over.
Extent of removal:1Front fork removal
7 Nm (0.7 m•kg, 5.1 ft•lb)
7 Nm (0.7 m•kg, 5.1 ft•lb)
7 Nm (0.7 m•kg, 5.1 ft•lb)
21 Nm (2.1 m•kg, 15 ft•lb)
21 Nm (2.1 m•kg, 15 ft•lb)
EC550000
FRONT FORK
1C3-9-32-5B 4/7/06 2:47 PM Page 2

Extent of removal Order Part name Q’ty Remarks
Preparation forHANDLEBAR REMOVAL
removal
Number plateRemove the band only.
1 Clutch cable 1 Disconnect at the lever side.
2 Clutch lever holder 1
3 “ENGINE STOP” button 1
4 Master cylinder 1 Refer to “REMOVAL POINTS”.
5 Throttle cable cap 1 Turn over the cap cover.
6 Throttle cable 1 Disconnect at the throttle side.
7 Throttle 1 Loosen the bolts.
8 Cap cover 1
9 Collar 1
10 Grip (left) 1 Refer to “REMOVAL POINTS”.
11 Handlebar holder (upper) 2
12 Handlebar 1
13 Handlebar holder (lower) 2
5-42
CHASHANDLEBAR
EC5B0000
HANDLEBAR
1
Extent of removal:1Handlebar removal
1 Nm (0.1 m•kg, 0.7 ft•lb)
4 Nm (0.4 m•kg, 2.9 ft•lb)
9 Nm (0.9 m•kg, 6.5 ft•lb)
28 Nm (2.8 m•kg, 20 ft•lb)
4 Nm (0.4 m•kg, 2.9 ft•lb)
4 Nm (0.4 m•kg, 2.9 ft•lb)
40 Nm (4.0 m•kg, 29 ft•lb)
1C3-9-32-5C 4/14/06 12:05 PM Page 2