2007 YAMAHA YD110 fuel pressure

OPERATION AND IMPORTANT RIDING POINTS
Tips for reducing fuel
consumptionb±/ku dh [kir de djus ds fVIlYour Motorcycle’s fuel consumption
depends to a large extent on your
riding style.vkidh e¨Vj&lkbZfdy esa b±/ku dh [k+ir]
vkids pykus ds rjhds ij fuHkZj djrh gSAThe following tips can help reduce fuel
consumption :uhps fn, x, fVIl ¼fof/k;k¡½ b±/ku dh [k+ir
d¨ de djus esa lgk;d g¨ ldrs gS
:
1. Warm up the engine before riding.
e¨Vj&lkbZfdy pykus ls igys batu
d¨ FkksM+k xeZ djsaA
2. Lift up the Choke Lever as soon
as possible.
ftruh tYnh laHko g¨ *pkWd yhoj^ d¨
Åij dh rjQ mBk ysaA
3. Shift up swiftly and avoid high
engine speeds during
acceleration.
xh;j rst+h ls cnys vkSj xfr cM+krs
le; batu dks t+:jr ls vf/kd LihM+
u nsaA
4. Do not double-clutch or rev the
engine while shifting down and
avoid high engine speeds with
no load on the engine.
xkM+h d¨ fupys xh;j esa ykrs le;
Mcy Dyp dk ç;¨x u djsaA rFkk
batu ij y¨M u g¨us dh fLFkfr esa
batu ds rhoz osx ls cpsaA
5. Turn off the engine instead of
letting it idle for an extended
length of time, i.e. in traffic jams,
at traffic lights or rail-road
crossings.
tc vki T;knk nsj rd [kM+s gks rks
batu dk vkbZMy ij pyrs jgus dh
vis{kk mls can dj nsaA
mnkgj.k% VªSfQd tke esa]yky cÙkh
ij] jsyos Øk£lx ij bR;kfnA
6. Do not drive with excessive load
on the Motorcycle.
vR;kf/kd ot+u ds lkFk
e¨Vj&lkbZfdy u pyk,¡A
7. Plan your route in advance.
vius ;k=kk&ekxZ dh ;¨t+uk igys ls
gh cuk ysaA
8. Avoid frequent braking.
ckj&ckj czsd yxkus ls cpsaA
9. Always maintain your tyre
pressure as per
recommendation.
tSlk fd çLrkfor ¼flQkfj'k½ fd;k
x;k gS] ges'kk vius Vk;j esa gok ds
ncko d¨ cuk dj j[¨saA
10.Get your motorcycle serviced
periodically after every 2000 kms.
çR;sd
2000
fdñehñ ds varjky esa
lkef;d #i ls e¨Vj&lkbZfdy dh
lfoZl djok,¡A
Running-in
jfuax&bu
There is never a more important period
in the life of your Motorcycle than the
period between zero and 1,000 km.
For this reason we ask that you
carefully read the following material.
Because the engine is brand new, you
must not put an excessive load on it
for the first 1,000 km. The various
parts in the engine wear and polish
themselves to the correct operating
clearances. During this period,
prolonged full throttle operation, or any
condition which might result in
excessive heating of the engine, must
be avoided.
5.4
dk;Z rFkk lokjh ls tqM+s vko';d rF;
PG1_55.pmd10/15/2006, 9:15 AM 37

1. Tread depth
VsªªM MsIFk
2. Side wall
lkbM okWy
Tyres
Vk;j
To ensure maximum performance, long
service and safe operation, note the
following:vR;f/kd dk;Z{kerk] nh?kZ l£ol v©j lqjf{kr
dk;Z ds fy, fuEufyf[kr ij /;ku nsa %1. Tyre air pressure
Always check and correct the tyre
pressure before operating the
Motorcycle.
Vk;j esa gok dk ncko
e¨Vj&lkbZfdy pykus ls igys ges'kk Vk;j
esa gok ds ncko d¨ tk¡p ys v©j bls
O;ofLFkr djasA
1. Free play
Ýh Iys
2. Locknut
ykWd uV
3. Adjusting nut
,Mt¯LVx uV
1. Loosen the locknut.
ykWd uV dks 2. Turn the adjusting nut in direction
ç to increase free play and in
direction è to decrease free play.
Ýh Iys d¨ c<+kus ds fy, ,Mt¯LVx uV
d¨ , dh fn'kk esa ?kqek,¡ rFkk Ýh Iys d¨
de djus ds fy, bls ch fn'kk esa ?kqek,¡A
3. Tighten the locknut.
ykWd uV d¨ dl nsaA
Valve clearance adjustment:okYo dh Dyh;jsal dk rkyesy %The correct valve clearance changes
with use, resulting in improper fuel/
air supply or engine noise. To prevent
this, the valve clearance must be
adjusted regularly. This adjustment
however, should be left to a YMIS
dealer.mfpr okYo Dyh;jsal t¨ fd batu ds ç;¨x
ds lkFk cnyrk jgrk gS] vuqfpr b±/ku@gok
dh lIykbZ vFkok batu esa 'k¨j dk dkj.k curk
gSA blds cpus ds fy, okYo ds Dyh;jsal d¨
yxkrkj O;ofLFkr djrs jguk pkfg,A oSls bl
rjg ds ,MtLVesaV ¼ rkyesy½ d¨
okbZñ,eñvkbZñ,lñ Mhyj }kjk gh djok;k tkuk
pkfg,A
KEEP RECOMMENDED TYRE PRESSURE IN BOTH THE TYRES
n¨u¨ Vk;j¨a esa vuqe¨fnr ok;q&ncko gh j[ksaA
6.18
PERIODIC MAINTENANCE AND MINOR REPAIRlkef;d j[kj[kko rFkk ekewyh ejEer
PG1_55.pmd10/15/2006, 9:15 AM 56

JOBS TO BE CARRIED OUT DURING FIFTEENTH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignment marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-2
DETGREEN.pmd10/15/2006, 8:50 AM 2

JOBS TO BE CARRIED OUT DURING FOURTEENTH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignment marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-4
DETGREEN.pmd10/15/2006, 8:50 AM 4

JOBS TO BE CARRIED OUT DURING THIRTEENTH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignment marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-6
DETGREEN.pmd10/15/2006, 8:50 AM 6

JOBS TO BE CARRIED OUT DURING TWELVETH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignment marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-8
DETGREEN.pmd10/15/2006, 8:50 AM 8

JOBS TO BE CARRIED OUT DURING ELEVENTH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignment marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-10
DETGREEN.pmd10/15/2006, 8:50 AM 10

JOBS TO BE CARRIED OUT DURING EIGHTH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignment marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-16
DETGREEN.pmd10/15/2006, 8:50 AM 12