2007 YAMAHA YD110 battery

8. If storing in a humid or salt-air
atmosphere, coat all exposed
parts with anti corrasive chemical
to prevent moisture from
entering.
;fn okrkoj.k esa vf/kd ueh o ued
dh ek=kk vf/kd gS rks /kkrq ds lHkh
egÙoiw.kZ ikVZl ij t+x izrhjks/kh jlk;u
dk bLrseky djsaA
9. Remove the battery and charge
it. Store it in a dry place and
recharge it once a month. Do not
store the battery in an excessively
warm or cold place (less than 0ºC
or more than 30ºC)
9.
cSV~jh dks ckgj fudky ysa vkSj bls
pkt+Z djsaA bls 'kq"d & LFkku ij
laHkkydj j[ksa vkSj eghus esa ,d
ckj fQj ls pkt+Z djsaA cSV~jh dks
vR;kf/kd xeZ vFkok B.Ms LFkku ij u
j[ksaA ¼
00 lsaVhxzsM ls uhps vkSj
300
lsaVhxzsM ls Åij½A
7.4
NOTE :Make any necessary repairs before
storing the Motorcycles.uksV %eksVjlkbfdy dks Hk.Mkj.k djus ls igys
gj rjg dh t:jr&ejEer ¼fjis;j½
iwjh dj ysaA
CLEANING AND STORAGE
lQkbZ rFkk HkaMkj.k
pg56_96.pmd10/15/2006, 8:53 AM 87

Wheels:
Ty p e :
FrontSpoke wheel
RearSpoke wheel
Size:Front1.60 × 18
Rear1.60 × 18
Brake:
Front :
Type Drum brake
operationright Hand lever
Rear :
Type Drum brake
Operation Right foot operation
Suspention :
Front Telescopic fork
RearSwing arm
Shock absorber:
Front Coil spring/oil damper
RearCoil spring/oil damperWheels travel:
Front 110 mm
Rear 70 mm
Electrical:
Ignition system:CDI (Digitally
Controlled)
Generator system:
Type Flywheel magneto
Standard output 12V
Battery:
Type Lead acid
Voltage, capacity 12V 2.5AH
Bulb voltage, Wattage × Quantity:
Headlight12V 35W/35W × 1
Tail/Brake light 12V 21W/5W × 1
Front flasher light 12V 10W × 2
Rear flasher light 12V 10W × 2
Meter light 12V 2W × 1
Neutral indicator light 12V 3.4W × 1
High beam indicator light 12V 3.4W × 1
Turn indicator light 12V 3.4W × 1
Fuse:
Main 10A
8.5
SPECIFICATIONSfo'ks"k fooj.k
pg56_96.pmd10/15/2006, 8:53 AM 92

WARRANTY
9.7
okjaVhWARRANTY ON PROPRIETARY ITEMSizksijk;Vjh mRiknksa ij okjaVh%&Warranty claims in respect of proprietary items like Tyres, Tubes, Battery and Spark Plug are warranted by their
respective manufacturers and shall be claimed on directly by the customer as per their warranty terms. YAMAHA
and its Authorised Dealers will give all assistance in taking up such claims with the manufacturer of said items.LokfeRo vkbVe¨a ¼ççkWbZVjh vkbZVeks½ tSls Vk;j] V~;wc] cSVjh v©j LikdZ Iyx ls lacaf/kr okjaVh nkos ¼Dyse½ muds fuekZrkv¨a ds
’'krks± o fu;eksa ds
vuqlkj
miHkksDrk }kjk muls lh/ks gh fy;k tk;sxkA ;kekgk v©j blds vf/kÑr Mhyj] mij¨Dr oLrqv¨a ds fuekZrkv¨a ds lkFk] bl rjg ds nkoksa
¼Dysel½ ds fuiVkjs fy, miHkksDrk dh lgk;rk djsaxsaA
THIS WARRANTY SHALL NOT BE APPLICABLE TO;g *okjaVh^ fuEu ifjfLFkfr;ksa esa ykxw ugh gksxh tSls %1. Normal maintenance operations such as Engine tune-up, Decarbonising, Fuel System Cleaning, Wheels,
Brakes and Clutch adjustments as well as any other normal adjustment.
lkekU; ejEer ds dk;Z] tSls fd batu dh V~;w¯ux] fMdkcksZukb¯tx] b±/ku iz.kkyh dh lQkbZ] ifg;¨a] czsd v©j Dyp dh ,MtLVeSaV ds
lkFk&lkFk dksbZ nwljh lk/kkj.k ,MtLVeSaVA
2. Normal replacement of service wear and tear items, i.e. Break Shoes, Fasteners/Shims/Washers, Gaskets
and Rubber or Plastic Components, ( other than tyres & tubes ) oil seals, Cables electrical wiring and
Electrical Items like Bulbs, Filters, Spark Plugs, Drive Chain, Sprocket, Clutch plate, Race Bearing & Element
Air Cleaner and wheel rim misalignment or bend.
eksVjlkbZfdy pykus ds n©jku f?kls rFkk [kjkc gq, ikVZ~l mnkgj.kr% czsd
'kwt+] QkLVulZ@f
'kel@ok
'klZ] xSlfdV rFkk jcM+ ;k IykfLVd
ds daiksusaV ¼Vk;j o V;wc ds bZykok½] vkW;y lhYl] rkjsa v©j bySDVªhdy vkbVe&tSls fd cYc] fQYVj] LikdZ Iyx] Mªkbo&psu] LçkWfdV]
Dyp IysV~l] jsl cs;¯jx vkSj ,yhesaV ,;j Dyhuj rFkk Oghy fje dh felvykbZueSaV ;k Vs<+k gksukA
pg97_103.pmd10/17/2006, 8:35 AM 101

JOBS TO BE CARRIED OUT DURING FIFTEENTH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignment marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-2
DETGREEN.pmd10/15/2006, 8:50 AM 2

JOBS TO BE CARRIED OUT DURING FOURTEENTH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignment marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-4
DETGREEN.pmd10/15/2006, 8:50 AM 4

JOBS TO BE CARRIED OUT DURING THIRTEENTH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignment marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-6
DETGREEN.pmd10/15/2006, 8:50 AM 6

JOBS TO BE CARRIED OUT DURING TWELVETH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignment marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-8
DETGREEN.pmd10/15/2006, 8:50 AM 8

JOBS TO BE CARRIED OUT DURING ELEVENTH PAID SERVICE 1. Note down the customer’s observations.
2. Wash Motorcycle and blow it dry with compressed air.
3. Clean Spark Plug and reset the gap if necessary.
4. Check Valve clearance, adjust if necessary.
5. Clean and tune Carburettor, set the idle RPM, as recommended. Check for the easy operation of Choke Lever.
6. Open and clean Fuel Cock and Fuel Filter. Check for any cracks or damage on Fuel Hose.
7. Clean Air Filter Element and lubricate it with (4T) oil.
8. Replace Engine Oil and check for any leakages.
9. Wash Engine Oil Filter Screen with petrol.
10. Check operation of Front & Rear Brakes, adjust if necessary. Grease the Brake Cam.
11. For proper Clutch functioning, check alignment marks on Crank Case L.H., Adjust if necessary.
12. Check for Wheel Runout/Spokes looseness, repair if necessary.
13. Check Wheel Bearings (Front & Rear) for looseness, damage.
14. Check for Steering looseness / tightness, adjust if required.
15. Check Front Fork operation / oil leakages, repair if reqrired.
16. Check for Rear Shock Absorber operation.
17. Check Chain Slackness, alignment. Adjust if necessary. Clean and lubricate.
18. Clean Battery, check electrolyte level and proper routing of Breather Pipe.
19. Tighten all Nuts and Bolts. Specially, Cylinder Head, Engine Mounting, Rear Swing Fork, Front & Rear Wheel
Axles & Rear Shock Absorber Mountings to the specified torque.
20. Check all electrical operations.
21. Check and correct air pressure in Front and Rear Tyres.
22. Lubricate all the pivot points.
23. Check exhaust emission for ‘CO’ level at idling, correct if required.
24. Clean and polish Motorcycle after taking ROAD TEST.
10-10
DETGREEN.pmd10/15/2006, 8:50 AM 10