2007 YAMAHA XMAX 250 cooling

EAU15605
Pre-operation check list
PRE-OPERATION CHECKS
4-2
4
ITEM CHECKS PAGE
• Check fuel level in fuel tank.
Fuel• Refuel if necessary. 3-4, 3-12
• Check fuel line for leakage.
• Check oil level in engine.
Engine oil• If necessary, add recommended oil to specified level. 6-8
• Check vehicle for oil leakage.
Final transmission oil• Check vehicle for oil leakage. 6-10
• Check coolant level in reservoir.
Coolant• If necessary, add recommended coolant to specified level. 6-11
• Check cooling system for leakage.
• Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check brake pads for wear.
Front brake• Replace if necessary. 3-10, 6-17 ~ 6-19
• Check fluid level in reservoir.
• If necessary, add recommended brake fluid to specified level.
• Check hydraulic system for leakage.
• Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check brake pads for wear.
Rear brake• Replace if necessary. 3-10, 6-17 ~ 6-19
• Check fluid level in reservoir.
• If necessary, add recommended brake fluid to specified level.
• Check hydraulic system for leakage.
• Make sure that operation is smooth.
Throttle grip• Check cable free play.
5-2, 6-14, 6-20
• If necessary, have Yamaha dealer adjust cable free play
and lubricate cable and grip housing.
• Check for damage.
Wheels and tires• Check tire condition and tread depth.
6-15 ~ 6-17, 6-23
• Check air pressure.
• Correct if necessary.
1C0-F8199-E3.qxd 2/11/06 20:46 Página 2

ODOMETER READING (x 1000 Km) ANNUAL
NO. ITEM CHECK OR MAINTENANCE JOB CHECK
110203040
8* Brake hose • Check for cracks or damage.
√√√√ √• Replace. Every 4 years
9*Wheels • Check runout and for damage. √√√√
• Check tread depth and for damage.
10 * Tires • Replace if necessary.
√√√√ √
• Check air pressure.
• Correct if necessary.
11 * Wheel bearings • Check bearing for looseness or damage. √√√√
12 *Steering bearings • Check bearing play and steering for roughness.
√√ √ √√• Lubricate with lithium-soap-based grease. Every 20000 km
13 * Chassis fasteners • Make sure that all nuts, bolts and screws are
properly tightened. √√√√ √
14 Sidestand, centerstand • Check operation.
• Lubricate. √√√√ √
15 *
Sidestand switch • Check operation. √√ √ √√ √
16 *Front fork • Check operation and for oil leakage. √√√√
17 * Shock absorber
assemblies • Check operation and shock absorbers for oil leakage.
√√√√
18 *Fuel injection • Check engine idle speed. √√ √ √√ √
• Change. (See pages 6-8.) √When the oil change indicator flashes
19
Engine oil (every 3000 km)• Check oil level and vehicle for oil leakage. Every 3000 km
√
20 *Engine oil strainer • Clean. √
21 *Cooling system • Check coolant level and vehicle for coolant leakage.
√√√√ √
• Change. Every 3 years
PERIODIC MAINTENANCE AND MINOR REPAIR
6-4
6
1C0-F8199-E3.qxd 10/1/07 18:13 Página 11

Engine overheatingEWA10400
s s
WARNING
Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be
blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled.
After removing the radiator cap retaining bolt, place a thick rag, like a towel, over the radiator cap, and then
slowly rotate the cap counterclockwise to the detent to allow any residual pressure to escape. When the his-
sing sound has stopped, press down on the cap while turning it counterclockwise, and then remove the cap.
PERIODIC MAINTENANCE AND MINOR REPAIR
6-31
6
Wait until the
engine has cooled.Check the coolant level in the
reservoir and radiator.
The coolant level
is OK.
The coolant level is low.
Check the cooling system
for leakage.
Have a Yamaha dealer checkand repair the cooling system.
Add coolant. (See NOTE.)
Start the engine. If the engine overheats again, have a
Yamaha dealer check and repair the cooling system.
There is
leakage.
There is
no leakage.
NOTE:
If coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended
coolant as soon as possible.
1C0-F8199-E3.qxd 2/11/06 20:46 Página 38

DimensionsOverall length2210 mm (87.0 in)
Overall width 790 mm (31.1 in)
Overall height 1380 mm (54.3 in)
Seat height 785 mm (30.9 in)
Wheelbase 1545 mm (60.8 in)
Ground clearance 112.7 mm (4.44 in)
Minimum turning radius 3650 mm (143.7 in)
WeightWith oil and fuel176 kg (388 lb)
EngineEngine typeLiquid cooled 4-stroke, SOHC
Cylinder arrangement Forward-inclined single cylinder
Displacement 249.7 cm
3(15.24 cu*in)
Bore x stroke 69.0 x 66.8 mm (2.71 x 2.63 in)
Compression ratio 10:01
Starting system Electric starter
Lubrication system Wet sump
Oil type or gradeEngine oilSAE 10W30
Recommended engine oil grade API service SE, SF, SG type or higher
Engine oil quantityPeriodic oil change1.2 L (1.27 US qt) (1.06 Imp qt)
Final transmission oilTypeYAMALUBE 4 (10W30) of SAE10W30
type SE motorolie
Quantity 0.25 L (0.26 US qt) (0.22 Imp qt)
Cooling systemRadiator capacity (including all routes)0.34 L (0.36 US qt) (0.30 Imp qt)
Coolant reservoir capacity (up to the
maximum level mark) 0.26 L (0.23 Imp qt, 0.28 US qt)
Air filterAir filter elementDry element
Recommended fuelRecommended fuelUnleaded fuel
Fuel tank capacity 12.5 L (3.30 US gal) (2.75 Imp gal)
Fuel reserve amount 2 L (0.53 US gal) (0.44 Imp gal)
Fuel injectionManufacturerAISAN Type x quantity
EFI System x 1
Spark plug (s)Manufacturer/modelNGK/DPR8EA-9
Spark plug gap 0.8-0.9 mm (0.031-0.035 in)
ClutchClutch typeDry, automatic centrifugal
TransmissionPrimary reduction systemHelical gear
Primary reduction ratio 40/15 (2.666)
Secondary reduction system Helical gear
Secondary reduction ratio 40/14 (2.857)
Transmission type V-belt automatic
Operation Centrifugal automatic type
ChassisFrame typeSteel tube underbone
Caster angle 28 º
Trail 100 mm (3.94 in)
Front tireTypeTubeless
SPECIFICATIONS
8-1
8
1C0-F8199-E3.qxd 16/11/06 19:33 Página 1