2007 YAMAHA XMAX 250 brake light

ODOMETER READING (x 1000 Km) ANNUAL
NO. ITEM CHECK OR MAINTENANCE JOB CHECK
110203040
22 Final transmission oil • Check vehicle for oil leakage.
√√ √• Change.√√√√
23 *V-belt • Replace. Every 20000 km
24 * Front and rear brake
switches • Check operation.
√√ √ √√ √
25Moving parts and cables • Lubricate. √√√√ √
Throttle grip housing • Check operation and free play.
26 * • Adjust the throttle cable free play if necessary.
√√√√ √
and cable
• Lubricate the throttle grip housing and cable.
27 * Lights, signals and
• Check operation.
switches • Adjust headlight beam. √√ √ √√ √
PERIODIC MAINTENANCE AND MINOR REPAIR
6-5
6EAUM2070
NOTE:
The air filter needs more frequent service if you are riding in unusually wet or dusty areas.
Hydraulic brake service
• Regularly check and, if necessary, correct the brake fluid level.
• Every two years change the brake fluid.
• Replace the brake hoses every four years and if cracked or damaged.
1C0-F8199-E3.qxd 10/1/07 18:13 Página 12

EAU24240
Replacing a front turn signal
light bulb
1. Place the scooter on the centers-tand.
2. Remove cowling A. (See page 6-6.)
3. Remove the socket (together with the turn signal light bulb) by
turning it counterclockwise.
1. Turn signal light bulb socket
4. Remove the defective bulb bypushing it in and turning it coun-
terclockwise.
5. Insert a new bulb into the socket, push it in, and then turn it clock-
wise until it stops.
6. Install the socket (together with the bulb) by turning it clockwise.
7. Install the cowling.
EAUS1250
Replacing the tail/brake light
bulb or a rear turn signal
light bulb
Tail/brake light bulb
1. Remove the tail/brake light bulb lens by removing the screw.
2. Remove the defective bulb by pushing it in and turning it coun-
terclockwise.
3. Insert a new bulb into the socket, push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the screw. Rear turn signal light bulb
1. Remove the tail/brake light lens by removing the screw.
2. Remove the turn signal light bulb lens by removing the screw.
3. Remove the defective bulb by pushing it in and turning it coun-
terclockwise.
4. Insert a new bulb into the socket, push it in, and then turn it clock-
wise until it stops.
5. Install the turn signal light bulb lens by installing the screw.
6. Install the tail/brake light bulb lens by installing the screw.
1
PERIODIC MAINTENANCE AND MINOR REPAIR
6-27
6
1C0-F8199-E3.qxd 4/11/06 09:44 Página 34

thinner, fuel (gasoline), rust
removers or inhibitors, brake
fluid, antifreeze or electrolyte.
Do not use high-pressure was-
hers or steam-jet cleaners sin-
ce they cause water seepage
and deterioration in the follo-
wing areas: seals (of wheel and
swingarm bearings, fork and
brakes), electric components
(couplers, connectors, instru-
ments, switches and lights),
breather hoses and vents.
For scooters equipped with a
windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or scrat-
ching. Some cleaning com-
pounds for plastic may leave
scratches on the windshield.
Test the product on a small hid-
den part of the windshield to
make sure that it does not lea-
ve any marks. If the windshield
is scratched, use a quality
plastic polishing compound
after washing.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottle-
brush for hard-to-reach areas. Stub-
born dirt and insects will come off
more easily if the area is covered with
a wet cloth for a few minutes before
cleaning.
After riding in the rain, near the sea or
on salt-sprayed roads
Since sea salt or salt sprayed on the
roads during winter are extremely
corrosive in combination with water,
carry out the following steps after
each ride in the rain, near the sea or
on salt-sprayed roads.
NOTE:
Salt sprayed on roads in the winter
may remain well into spring.
1. Clean the scooter with cold water
and a mild detergent after the
engine has cooled down.
ECA10790
CAUTION:
Do not use warm water since it
increases the corrosive action of
the salt.
2. Apply a corrosion protection
spray on all metal, including
chrome- and nickel-plated, surfa-
ces to prevent corrosion.
After cleaning
1. Dry the scooter with a chamois or
an absorbing cloth.
2. Use a chrome polish to shine
chrome, aluminum and stainless-
steel parts, including the exhaust
system. (Even the thermally indu-
ced discoloring of stainless-steel
exhaust systems can be removed
through polishing.)
3. To prevent corrosion, it is recom-
mended to apply a corrosion pro-
tection spray on all metal, inclu-
ding chrome- and nickel-plated,
surfaces.
4. Use spray oil as a universal clea-
ner to remove any remaining dirt.
5. Touch up minor paint damage
caused by stones, etc.
SCOOTER CARE AND STORAGE
7-2
7
1C0-F8199-E3.qxd 2/11/06 20:46 Página 2

Size120/70-15 M/C 56S(Michelin)
120/70-15 M/C 56P(Pirelli)
Manufacturer/model MICHELIN/GOLD STANDARD
PIRELLI/GTS23
Rear tireTypeTubeless
Size 140/70-14 M/C 68S(Michelin)
140/70-14 M/C 68P(Pirelli)
Manufacturer/model MICHELIN/GOLD STANDARD
PIRELLI/GTS24
LoadingMaximum load180 kg (396.9 lb)
Load is total weight of the equipement, dri-
ver, passenger and accessories
Tire air pressure (measured on cold
tires)
Loading condition 0–90 kg (0–198 lb)
Front 190 kPa (27 psi) (1.9 kgf/cm
2)
Rear 220 kPa (31 psi) (2.2 kgf/cm
2)
Loading condition 90 kg (198 lb)–Maximum load
Front 210 kPa (30 psi) (2.1 kgf/cm
2)
Rear 250 kPa (36 psi) (2.5 kgf/cm
2)
Front wheelWheel typeAluminium wheel
Rim size 15 x MT3.50
Rear wheelWheel typeAluminium wheel
Rim size 14 x MT3.75
Front brakeTypeSingle disc brake
Operation Right hand operation
Recommended fluid DOT 4
Rear brakeTypeSingle disc brake
Operation Left hand operation
Recommended fluid DOT 4
Front suspensionTypeTelescopic fork
Spring/shock absorber type Coil spring/oil damper
Wheel travel 110 mm (4.33 in)
Rear suspensionTypeUnit swing Spring/shock absorber type
Coil spring/oil damper
Wheel travel 95 mm (3.74 in)
Electrical systemIgnition systemTransistorized coil ignition (digital)
Charging system AC magneto
BatteryManufacturer/modelYuasa/YTX9-BS
Voltage, capacity 12 V, 8.0 Ah
Bulb voltage, wattage x quantity
Headlight12 V, 35.0 W / 35.0 W x 2
Auxiliary light 12 V, 5.0 W x 2
Tail/brake light 12 V, 21.0 W / 5.0 W x 2
Front turn signal light 12 V, 10.0 W x 2
Rear turn signal light 12 V, 10.0 W x 2
License plate light 12 V, 5.0 W x 1
Meter lighting LED
Fuel level warning lamp LED
High beam Indicator light LED
SPECIFICATIONS
8-2
8
1C0-F8199-E3.qxd 7/11/06 12:14 Página 2

AAcceleration and deceleration ...................5-2
Air filter and V-belt case air filter
elements ................................................6-12
Anti-theft alarm (optional) ..........................3-8
Auxiliary light bulb, replacing ...................6-28
BBattery......................................................6-23
Brake fluid level, checking .......................6-18
Brake fluid, changing ...............................6-19
Brake lever, front ......................................3-10
Brake lever, rear .......................................3-10
Brake levers, lubricating ..........................6-20
Braking .......................................................5-3
CCables, checking and lubricating ............6-20
Care............................................................7-1
Catalytic converter ...................................3-13
Centerstand and sidestand, checking
and lubricating .......................................6-21
Coolant.....................................................6-11
Coolant temperature gauge .......................3-5
Cowlings and panel, removing and
installing ...................................................6-6
DDimmer switch ...........................................3-9
Display, multi-function ...............................3-5
EEngine break-in ..........................................5-4
Engine oil ...................................................6-8
Engine trouble warning light ......................3-3
FFinal transmission oil ...............................6-10
Front and rear brake lever free play.........6-17
Front and rear brake pads, checking ......6-18Front fork, checking .................................6-21
Fuel ..........................................................3-12
Fuel consumption, tips for reducing ..........5-3
Fuel gauge .................................................3-4
Fuel level warning light ..............................3-3
Fuel tank cap ...........................................3-11
Fuses, replacing .......................................6-24
HHandlebar switches ...................................3-9
Hazard switch ............................................3-9
Headlight bulb, replacing .........................6-25
High beam indicator light...........................3-3
Horn switch ................................................3-9
IIdentification numbers ...............................9-1
Ignition circuit cut-off system ..................3-18
Immobilizer system ....................................3-1
Immobilizer system indicator light .............3-4
Indicator and warning lights ......................3-3
KKey identification number ..........................9-1
LLicense plate light bulb, replacing ...........6-28
MMain switch/steering lock ..........................3-2
Matte color, caution ...................................7-1
Model label ................................................9-2
PParking .......................................................5-4
Part locations .............................................2-1
Periodic maintenance and lubrication
chart .........................................................6-3
Pre-operation check list .............................4-2
SSafe-riding points.......................................1-4Safety information ......................................1-1
Seat ..........................................................3-13
Shock absorber assemblies, adjusting....3-17
Sidestand .................................................3-17
Spark plug, checking .................................6-7
Specifications.............................................8-1
Speedometer .............................................3-4
Start switch ................................................3-9
Starting a cold engine ................................5-1
Starting off .................................................5-2
Steering, checking ...................................6-22
Storage.......................................................7-3
Storage compartment (front) ...................3-15
Storage compartment (rear) .....................3-16
Storage compartments ............................3-14
TTail/brake light bulb or rear turn signal
light bulb, replacing ...............................6-27
Throttle cable free play, adjusting ............6-14
Throttle grip and cable, checking and
lubricating ..............................................6-20
Tires .........................................................6-15
Tool kit ........................................................6-1
Troubleshooting .......................................6-29
Troubleshooting charts ............................6-30
Turn signal indicator lights .........................3-3
Turn signal light bulb (front), replacing ....6-27
Turn signal switch ......................................3-9
VValve clearance ........................................6-14
Vehicle identification number .....................9-1
WWheel bearings, checking........................6-23
Wheels .....................................................6-17
INDEX
1C0-F8199-E3.qxd 2/11/06 20:46 Página 6