2007 YAMAHA WOLVERINE 450 brake light

6-4
6Shifting: Neutral to Reverse and Reverse to
Park
NOTE:The drive select lever cannot be shifted into or fromreverse or park without applying the brake pedal.
1. Bring the ATV to a complete stop.
2. Apply the brake pedal.
3. Shift from neutral to reverse or from reverse to
park and vice versa by moving the drive select
lever along the shift guide.
NOTE:
When in reverse, the reverse indicator light
should come on. If the indicator light does not
come on, have a Yamaha dealer check the elec-
trical circuit.
Due to the synchronizing mechanism in the en-
gine, the indicator light may not come on until theATV starts moving.
4. Check behind for people or obstacles, and
then release the brake pedal.
5. Open the throttle lever gradually and continue
to watch to the rear while backing.
WARNING
EWB00720Improper operation in reverse could make you
hit an obstacle or even a person behind you,
resulting in serious injury. When you shift into
reverse, make sure there are no people or ob-
stacles behind you. When it is safe to proceed,go slowly.
1. Drive select lever
2. F (Forward)
3. N (Neutral)
4. R (Reverse)
5. P (Park)U3C261E0.book Page 4 Thursday, June 29, 2006 4:15 PM

8-6
8
26 Final gear oilChange.
Check ATV for oil leakage, and correct if neces-
sary.√√
27 Cooling systemCheck coolant level and ATV for coolant leakage,
and correct if necessary.√√√√√
Replace coolant. Every 2 years
28*Moving parts and
cablesLubricate.√√√√
29*Drive select lever
safety system cableCheck operation and adjust or replace if neces-
sary.√√√
30*Throttle lever hous-
ing and cableCheck operation and correct if necessary.
Check throttle cable free play and adjust if neces-
sary.
Lubricate throttle lever housing and cable.√√√√√
31*Exhaust systemCheck for leakage and replace gasket(s) if neces-
sary.
Check for looseness and tighten all screw clamps
and joints if necessary.√√√
32 Spark arresterClean.√√√
33*Front and rear brake
switchesCheck operation and correct if necessary.√√√√√
34*Lights and switchesCheck operation and correct if necessary.
Adjust headlight beams.√√√√√ NO. ITEMCHECK OR MAINTENANCE
JOBINITIAL EVERY
Whichev-
er comes
firstmonth136612
km
(mi)320
(200)1200
(750)2400
(1500)2400
(1500)4800
(3000)
hours 20 75 150 150 300U3C261E0.book Page 6 Thursday, June 29, 2006 4:15 PM

8-43
8
EBU24751Brake light switches The operation of the brake light switches must be
checked and, if necessary, adjusted at the inter-
vals specified in the periodic maintenance and lu-
brication chart.
The brake light switch for the brake pedal can be
adjusted as follows, but the other brake light
switches should be adjusted by a Yamaha dealer.
1. Remove panel A. (See page 8-8.)NOTE:The brake light switch is properly adjusted when
the brake light comes on just before braking takeseffect.
2. Turn the adjusting nut while holding the brake
light switch in place. To make the brake light
come on earlier, turn the adjusting nut in direc-
tion (a). To make the brake light come on lat-
er, turn the adjusting nut in direction (b).3. Install the panel.
EBU24900Checking and lubricating the cables The operation and the condition of all control ca-
bles should be checked before each ride, and the
cables and cable ends should be lubricated if nec-
essary. If a cable is damaged or does not move
smoothly, have a Yamaha dealer check or replace
it.1. Brake light switch
2. Brake light switch adjusting nutRecommended lubricant:
Engine oil
U3C261E0.book Page 43 Thursday, June 29, 2006 4:15 PM

8-51
8
CAUTION:ECB00670Make sure the headlight bulb holder cover is
securely fitted over the bulb holder and seatedproperly.
7. Adjust the headlight beam if necessary.EBU25560Adjusting a headlight beam CAUTION:ECB00690It is advisable to have a Yamaha dealer makethis adjustment.
To raise a headlight beam, turn the adjusting bolt
in direction (a).
To lower a headlight beam, turn the adjusting bolt
in direction (b).
EBU25600Replacing the tail/brake light bulb If the tail/brake light bulb burns out, replace it as
follows.
1. Remove the lens by removing the screws.1. Headlight beam adjusting bolt
U3C261E0.book Page 51 Thursday, June 29, 2006 4:15 PM

8-52
82. Remove the defective bulb by pushing it in
and turning it counterclockwise.3. Insert a new bulb into the socket, push it in,
and then turn it clockwise until it stops.
4. Install the lens by installing the screws.
CAUTION:ECB00700Do not overtighten the screws, otherwise thelens may break.EBU25650Removing a wheel 1. Loosen the wheel nuts.
2. Elevate the ATV and place a suitable stand
under the frame.
3. Remove the nuts from the wheel.
1. Screw
1. Tail/brake light bulb
1. Wheel nut
U3C261E0.book Page 52 Thursday, June 29, 2006 4:15 PM

10-4
10
Front suspension:Type:
Double wishbone
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel:
160 mm (6.3 in)Rear suspension:Type:
Swingarm
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel:
180 mm (7.1 in)Electrical system:Ignition system:
DC. CDI
Charging system:
AC magnetoBattery:Model:
YTX20L-BS
Voltage, capacity:
12 V, 18.0 AhHeadlight:Bulb type:
Krypton bulbBulb voltage, wattage x quantity:Headlight:
12 V, 30.0/30.0 W × 2Tail/brake light:
12 V, 5.0/21.0 W × 1
Neutral indicator light:
LED
Reverse indicator light:
LED
Coolant temperature warning light:
LED
Park indicator light:
LED
On-Command four-wheel-drive indicator:
LCD
Fuses:Main fuse:
30.0 A
Headlight fuse:
15.0 A
Signaling system fuse:
10.0 A
Ignition fuse:
10.0 A
Auxiliary DC jack fuse:
10.0 A
Backup fuse:
10.0 A
Four-wheel-drive motor fuse:
3.0 A
U3C261E0.book Page 4 Thursday, June 29, 2006 4:15 PM

INDEX
AAccessories and loading ................................................ 6-6
Air filter element, cleaning ............................................ 8-30
Axle boots .................................................................... 8-42BBattery .......................................................................... 8-45
Brake fluid, changing .................................................... 8-39
Brake fluid level, checking ............................................ 8-38
Brake lever free play and brake pedal position (rear),
adjusting and checking .............................................. 8-40
Brake lever free play, checking the front ...................... 8-40
Brake lever, front ............................................................ 4-7
Brake levers, checking and lubricating ......................... 8-44
Brake light switches ..................................................... 8-43
Brake pads, checking the front and rear ...................... 8-37
Brake pedal and rear brake lever ................................... 4-7
Brake pedal, checking and lubricating ......................... 8-44
Brakes, front and rear .................................................... 5-4CCables, checking and lubricating ................................. 8-43
Carburetor, adjusting .................................................... 8-34
Chassis fasteners ........................................................... 5-7
Cleaning ......................................................................... 9-1
Coolant .................................................................. 5-3, 8-25
Coolant temperature warning light ................................. 4-2
Cowlings and panels, removing and installing ............... 8-8DDifferential gear oil ......................................................... 5-3Differential gear oil, changing ....................................... 8-23
Drive select lever ............................................................ 4-8
Drive select lever and driving in reverse ........................ 6-3
Drive select lever safety system cable, adjusting ......... 8-37
Drive shaft universal joint, lubricating ........................... 8-45
EEngine break-in .............................................................. 6-5
Engine, cold start ........................................................... 6-1
Engine idling speed ...................................................... 8-35
Engine oil ....................................................................... 5-3
Engine oil and oil filter cartridge ................................... 8-16
Engine, starting a warm ................................................. 6-3
Engine stop switch ......................................................... 4-4FFinal gear oil .......................................................... 5-3, 8-21
Four-wheel-drive indicator .............................................. 4-2
Fuel ......................................................................... 4-9, 5-3
Fuel cock ...................................................................... 4-10
Fuel tank cap .................................................................. 4-8
Fuses, replacing ........................................................... 8-47HHandlebar switches ........................................................ 4-4
Headlight beam, adjusting ............................................ 8-51
Headlight bulb, replacing .............................................. 8-49IIdentification numbers .................................................. 11-1
Indicator lights and warning light .................................... 4-2
Instruments, lights and switches .................................... 5-7
U3C261E0.book Page 1 Thursday, June 29, 2006 4:15 PM

KKey identification number ............................................. 11-1LLabel locations ............................................................... 2-1
Light switch .................................................................... 4-4MMain switch .................................................................... 4-1
Model label ................................................................... 11-2NNeutral indicator light ..................................................... 4-2OOn-Command four-wheel-drive switch ........................... 4-5
Owner’s manual and tool kit ........................................... 8-1PPark indicator light ......................................................... 4-3
Parking ........................................................................... 6-5
Parking on a slope ......................................................... 6-5
Part locations ................................................................. 3-1
Periodic maintenance and lubrication chart ................... 8-3
Pre-operation check list ................................................. 5-1RReverse indicator light ................................................... 4-2
Riding your ATV ............................................................. 7-1SSafety information .......................................................... 1-1
Seat .............................................................................. 4-12
Shock absorber assemblies, adjusting the front .......... 4-14
Shock absorber assembly, adjusting the rear .............. 4-15
Spark arrester, cleaning ............................................... 8-32
Spark plug, checking .................................................... 8-14
Specifications ............................................................... 10-1Speed limiter .................................................................. 4-6
Speedometer unit .......................................................... 4-3
Starter (choke) ............................................................. 4-11
Start switch .................................................................... 4-4
Steering shaft, lubricating ............................................ 8-45
Storage .......................................................................... 9-2
Storage compartment .................................................. 4-13
TTail/brake light bulb, replacing ..................................... 8-51
Throttle cable free play, adjusting ................................ 8-36
Throttle lever ........................................................... 4-6, 5-5
Tire pressure, measuring ............................................... 5-6
Tires ............................................................................... 5-5
Tire wear limit ................................................................ 5-7
Troubleshooting ........................................................... 8-54
Troubleshooting charts ................................................ 8-55VValve clearance ........................................................... 8-36
V-belt case drain plug .................................................. 8-34
V-belt cooling duct check hose .................................... 8-34
Vehicle identification number ....................................... 11-1WWheel bearings, checking ............................................ 8-45
Wheel, installing ........................................................... 8-53
Wheel, removing .......................................................... 8-52
U3C261E0.book Page 2 Thursday, June 29, 2006 4:15 PM