2007 YAMAHA VX cruise control

Features and functions
33
“Selecting the normal mode/low-RPM mode”
for operation mode information.)
EJU31411Selecting the normal mode/low-RPM
mode (for VX Deluxe/VX Cruiser)
The normal mode and low-RPM mode can
only be selected when the engine is stopped
in the unlock mode. Press the unlock button
on the remote control transmitter for more
than 4 seconds to switch between the normal
mode and the low-RPM mode.
Normal mode
If the beeper sounds twice, the normal mode
is activated.
The watercraft can be ridden normally.Low-RPM mode
If the beeper sounds three times, the low-
RPM mode is activated and the “L-MODE” in-
dicator light comes on.
Maximum engine speed (r/min) in the low-
RPM mode is limited to approximately 90% of
the maximum engine speed in the normal
mode.
NOTE:

If neither the start switch nor the remote
control transmitter is operated within 25
seconds after the unlock button is pressed
to select the unlock mode, the multifunction
meter display and the “L-MODE” indicator
light will go off. If this occurs, press the lock
button on the transmitter briefly to select the
lock mode, press the unlock button briefly to
select the unlock mode, and then press the
unlock button again for more than 4 sec-
onds to select the normal mode or low-RPM
mode.

While the engine is running, input from the
remote control transmitter is not received.
CAUTION:
ECJ00080
If the remote control transmitter does not
operate when its buttons are pressed, the
battery may be low. Have a Yamaha dealer
replace the battery.
1Unlock button
Number
of beepsYamaha Security Sys-
tem modeEngine
can be
started
1 beep Lock NO
2 beepsUnlock
(normal mode)YES
3 beepsUnlock
(low-RPM mode)YES
1“L-MODE” indicator light
UF1K72E0.book Page 33 Wednesday, August 2, 2006 10:43 AM

Operation
49
turned, and that there is no free play between
the handlebars and the jet thrust nozzle.
EJU32630Shift lever and reverse gate (for VX Deluxe/
VX Cruiser)
Check the shift lever and reverse gate for
proper operation.
Make sure that the reverse gate goes down
completely when the shift lever is pulled up.
Also, make sure that the reverse gate goes up
completely when the shift lever is pushed
down.
WARNING
EWJ00480

Make sure that the throttle lever is com-
pletely released and that the engine is at
idle before shifting into reverse.

Do not use the reverse function to slow
down or stop the watercraft as it could
cause you to lose control, be ejected, or
impact the handlebars.

Use reverse for slow-speed maneuver-
ing only.

Make sure that there are no obstacles or
people behind you before shifting into
reverse.

Do not touch the reverse gate while the
shift lever is being operated, otherwise
you could be pinched.
EJU32650Jet intake
Carefully check the jet intake for weeds, de-
bris, or anything else that might restrict the in-
take of water. If the jet intake is clogged,
cavitation could occur, reducing jet thrust, and
possibly damaging the jet pump.
In some cases, the engine may overheat be-
cause of lack of cooling water, and damage to
the engine could result. Cooling water is fed to
the engine by the jet pump. (See page 82 for
jet intake cleaning procedures.)
WARNING
EWJ00470

Keep away from the intake grate while
the engine is on. Items such as long hair,
loose clothing, or PFD straps can be-
come entangled in moving parts, result-
ing in severe injury or drowning.

Stop the engine and remove the clip
from the engine shut-off switch before
removing any debris or weeds, which
UF1K72E0.book Page 49 Wednesday, August 2, 2006 10:43 AM

Operation
52
(1) Launch the watercraft and start the en-
gine. (See page 52 for engine starting
procedures.)
(2) For the first 5 minutes, run the engine at
trolling speed only. For the 30 minutes of
operation after that, keep the engine
speed below 5000 r/min. For the 1 hour of
operation after that, keep the engine
speed below 6500 r/min.
(3) Proceed with normal operation.
CAUTION:
ECJ00430
Failure to follow the engine break-in pro-
cedure could result in reduced engine life
or even severe engine damage.
EJU32811Launching the watercraft
When launching the watercraft, make sure
that there are no obstacles around you.
If there are waves, someone should make
sure that the watercraft is not pushed into the
trailer after launching the watercraft.

For VX Deluxe/VX Cruiser:
Use the remote control transmitter to select
the unlock mode. (See page 32 for Yamaha
Security System and low-RPM mode selec-
tion procedures.)
After the watercraft is in the water, start the
engine. Shift into reverse and move the wa-
tercraft back slowly.

For VX:
After the watercraft is in the water, turn it
around so that the bow faces the direction
you wish to go. Start the engine, and then
slowly move away from the launching area.
EJU32850Starting the engine
WARNING
EWJ00560
Never start the engine or let it run for any
length of time in an enclosed area. Ex-
haust fumes contain carbon monoxide, acolorless, odorless gas that may cause
loss of consciousness and death within a
short time. Always operate the watercraft
in an open area.
(1) If the lock mode of the Yamaha Security
System is selected (for VX Deluxe/VX
Cruiser), use the remote control transmit-
ter to select the unlock mode. (See page
32 for Yamaha Security System and low-
RPM mode selection procedures.)
(2) Launch the watercraft in water free from
weeds and debris and at least 60 cm (2 ft)
deep.
WARNING
EWJ00570
Never operate in water that is less than 60
cm (2 ft) deep, otherwise you increase
your chance of hitting a submerged ob-
ject, which could result in injury.
CAUTION:
ECJ00470
Never operate in water that is less than 60
cm (2 ft) deep, otherwise pebbles or sand
could be sucked into the jet intake, caus-
ing impeller damage and engine overheat-
ing.
UF1K72E0.book Page 52 Wednesday, August 2, 2006 10:43 AM

Operation
63
steer away from a boat or other obstacle
that comes into your path.

For VX Deluxe/VX Cruiser:
Do not use the reverse function to slow
down or stop the watercraft as it could
cause you to lose control, be ejected, or
impact the handlebars.
EJU35960Beaching the watercraft
(1) Make sure that there are no boats, swim-
mers, or obstacles near the beach. Re-
lease the throttle lever about 100 m (330
ft) before you reach the intended beach-
ing area.
(2) Approach the beach slowly and stop the
engine before reaching land.
Remember, you need throttle to steer.
(3) Get off the watercraft and pull it up on the
beach.
CAUTION:
ECJ00490
Small pebbles, sand, seaweed, and other
debris can be sucked into the jet intake
and impair or damage the impeller. Always
stop the engine and get off the watercraft
before beaching it.
EJU36060Docking the watercraft
(1) Make sure that there are no boats, swim-
mers, or obstacles near the watercraft.
Reduce speed about 100 m (330 ft) away
from the dock.
(2) Slowly approach the dock and stop the
engine just before coming alongside it.
EJU33320Reverse on waterways (for VX Deluxe/
VX Cruiser)
Reverse can be used for slow-speed maneu-
vering when it is necessary to back up out of
tight spots where you cannot turn around. Re-
verse can be used to slow down or stop onlyduring slow-speed maneuvering, such as
when docking.
Once the engine is idling, shift into reverse
and gradually increase engine speed. Make
sure that there are no obstacles or people be-
hind you before shifting into reverse.
EJU33350Rough water operation
The force of landing after jumping can cause
a strong impact on both the watercraft and the
operator and passengers. It is possible for the
operator to hit his or her chest or jaw on the
watercraft or handlebars and be injured. The
passengers could also impact the watercraft
and be injured.
Do not operate the watercraft with your chin
right above the handlebars. In addition, the
operator and passengers should keep their
feet on the floor of the footwell.
Operating in rough water or jumping waves
can also crack the watercraft hull and deck,
and damage internal parts. Avoid operating in
rough water or bad weather conditions.
UF1K72E0.book Page 63 Wednesday, August 2, 2006 10:43 AM

Trouble recovery
81
Engine runs irregu-
larly or stallsFuel Empty Refill as soon as pos-
sible42
Stale or contaminat-
edHave serviced by
Yamaha dealer73
Fuel tank Water or dirt present Have serviced by
Yamaha dealer73
Spark plug Fouled or defective Replace 75
Incorrect heat range Replace 75
Gap incorrect Adjust 75
Spark plug
capLoose Connect properly 75
Cracked, torn, or
damagedReplace
—
Electrical wir-
ingLoose connection Tighten or connect
properly—
Fuel injec-
tion systemFaulty or clogged in-
jectorsHave serviced by
Yamaha dealer—
Warning light or in-
dicator blinksFuel level Empty Refill as soon as pos-
sible42
Engine over-
heatedJet intake clogged Clean
82
Check engine
warningFaulty sensors Have serviced by
Yamaha dealer37
Watercraft slow or
loses powerYamaha Se-
curity Sys-
tem (VX
Deluxe/VX
Cruiser)Low-RPM mode se-
lectedSelect normal mode
33
Cavitation Jet intake clogged Clean 82
Impeller damaged or
wornHave serviced by
Yamaha dealer82
Engine over-
heat warningEngine speed reduc-
tion control activatedClean jet intake and
cool engine36
Oil pressure
warningEngine speed reduc-
tion control activatedAdd oil
35
Spark plug Fouled or defective Replace 75
Incorrect heat range Replace 75
Gap incorrect Adjust 75
Spark plug
capsLoose Connect properly
75
Electrical wir-
ingLoose connection Tighten or connect
properly—
Fuel Stale or contaminat-
edHave serviced by
Yamaha dealer73
Air filter Clogged or oil buildup Have serviced by
Yamaha dealer74 TROUBLE POSSIBLE CAUSE REMEDY PAGE
UF1K72E0.book Page 81 Wednesday, August 2, 2006 10:43 AM

Index
A
Air filter element ....................................... 74
Approval label of emission control
certificate ................................................ 3
B
Battery ................................................ 47, 68
Battery, checking...................................... 77
Battery, jumping ....................................... 83
Beaching the watercraft ........................... 63
Bilge ......................................................... 46
Boarding alone ......................................... 57
Boarding and starting from a dock ........... 57
Boarding and starting in deep water ........ 57
Boarding and starting in shallow water .... 56
Boarding with passengers ........................ 58
Bow eye ................................................... 31
Builder’s plate............................................. 2
C
Capsized watercraft ................................. 60
Check engine warning indicator ............... 37
Cleaning the watercraft ............................ 68
Cooling water pilot outlet .................... 29, 50
Cruising limitations ................................... 13
D
Docking the watercraft ............................. 63
E
Emergency procedures ............................ 82
Emission control information
(for Canada only) .................................... 3
Engine break-in ........................................ 51
Engine compartment ................................ 45
Engine oil ................................................. 42
Engine oil and oil filter .............................. 73
Engine oil level ......................................... 45
Engine overheat warning indicator ........... 36
Engine serial number ................................. 1
Engine shut-off cord ................................. 50
Engine shut-off switch .............................. 28
Engine stop switch ................................... 28
Enjoy your watercraft responsibly ............ 21
F
Filling the fuel tank ................................... 42
Fire extinguisher....................................... 48
Flushing the cooling system ..................... 66
Front storage compartment ...................... 38Fuel and oil............................................... 41
Fuel injection system ................................ 78
Fuel level .................................................. 45
Fuel level meter ........................................ 34
Fuel level warning indicator ...................... 35
Fuel system .............................................. 67
Fuel system, checking .............................. 73
Fuel tank .................................................. 73
Fuel tank filler cap .................................... 27
Fuses, replacing ....................................... 84
G
Gasohol .................................................... 41
Gasoline ................................................... 41
Getting to know your watercraft ............... 54
Glove compartment .................................. 39
H
Handgrip ................................................... 31
Hazard information ................................... 17
Hood ......................................................... 26
Hour meter/voltmeter ............................... 35
Hull and deck ........................................... 45
Hull Identification Number (HIN)................. 1
I
Identification numbers ................................ 1
Important labels .......................................... 5
J
Jet intake .................................................. 49
Jet intake and impeller, cleaning .............. 82
Jet thrust nozzle angle, checking ............. 74
Jumper cables, connecting ...................... 83
L
Labels, other .............................................. 9
Labels, warning .......................................... 6
Launching the watercraft .......................... 52
Learning to operate your watercraft ......... 54
Leaving the watercraft .............................. 54
Limitations on who may operate the
watercraft .............................................. 12
“L-MODE” indicator light
(for VX Deluxe/VX Cruiser) ................... 38
Lubrication................................................ 67
Lubrication points ..................................... 76
M
Main components, location of .................. 22
Maintenance and adjustments ................. 69
UF1K72E0.book Page 1 Wednesday, August 2, 2006 10:43 AM

Index
Manufactured date label............................. 4
Model information (for Europe only) ........... 2
Multifunction information center ......... 34, 51
O
Oil pressure warning indicator.................. 35
Operating your watercraft......................... 54
Operation ................................................. 51
Operation of controls and other
functions ............................................... 26
Operation requirements ........................... 14
Owner’s/operator’s manual and tool kit .... 70
P
Periodic maintenance chart...................... 71
Post-operation care .................................. 64
Pre-operation check list............................ 43
Pre-operation check points ...................... 45
Pre-operation checks ............................... 43
Primary Identification (PRI-ID) number ...... 1
R
Recommended equipment ....................... 16
Remote control transmitter
(for VX Deluxe/VX Cruiser) ................... 27
Reverse on waterways
(for VX Deluxe/VX Cruiser) ................... 63
Riding with passengers ............................ 55
Rough water operation ............................. 63
S
Safe boating rules .................................... 20
Seat .......................................................... 26
“SECURITY” indicator light
(for VX Deluxe/VX Cruiser) ................... 37
Selecting the normal mode/low-RPM
mode (for VX Deluxe/VX Cruiser) ......... 33
Shift cable, checking
(for VX Deluxe/VX Cruiser) ................... 74
Shift lever and reverse gate
(for VX Deluxe/VX Cruiser) ................... 49
Shift lever (for VX Deluxe/VX Cruiser) ..... 30
Spark plugs, cleaning and adjusting ........ 75
Speedometer............................................ 34
Start switch............................................... 29
Starting the engine ................................... 52
Starting the watercraft .............................. 56
Steering system ................................. 30, 48
Stern drain plugs ...................................... 47Stern eyes ................................................ 31
Stopping the engine ................................. 54
Stopping the watercraft ............................ 62
Storage..................................................... 66
Storage compartments ............................. 38
Submerged watercraft .............................. 85
Switches ................................................... 50
T
Tachometer .............................................. 34
Throttle cable, checking and adjusting ..... 75
Throttle lever ...................................... 29, 48
Towing the watercraft ............................... 85
Transporting ............................................. 65
Trolling speed, checking .......................... 78
Troubleshooting ....................................... 80
Troubleshooting chart .............................. 80
Turning the watercraft .............................. 61
W
Water separator ....................................... 46
Watercraft characteristics ......................... 17
Water-skiing ............................................. 19
Y
Yamaha Engine Management System
(YEMS) ................................................. 32
Yamaha Security System and
low-RPM mode
(for VX Deluxe/VX Cruiser) ................... 32
Yamaha Security System
(for VX Deluxe/VX Cruiser) ................... 32
Yamaha Security System lock and
unlock modes
(for VX Deluxe/VX Cruiser) ................... 32
UF1K72E0.book Page 2 Wednesday, August 2, 2006 10:43 AM