2007 YAMAHA TTR50 brake

TABLE OF CONTENTSSAFETY INFORMATION ..................1-1
Location of important labels ............1-4
DESCRIPTION ..................................2-1
Left view ..........................................2-1
Right view ........................................2-2
Controls and instruments.................2-3
INSTRUMENT AND CONTROL
FUNCTIONS.......................................3-1
Main switch .....................................3-1
Handlebar switches ........................3-1
Speed limiter ...................................3-2
Shift pedal .......................................3-2
Brake lever .....................................3-3
Brake pedal ....................................3-3
Fuel tank cap ..................................3-3
Fuel .................................................3-4
Fuel tank breather hose ..................3-5
Fuel cock ........................................3-5
Starter (choke) lever .......................3-6
Seat ................................................3-7
Sidestand ........................................3-7
Starting circuit cut-off system .........3-8
PRE-OPERATION CHECKS..............4-1
Pre-operation check list ..................4-2OPERATION AND IMPORTANT
RIDING POINTS................................. 5-1
Starting and warming up a cold
engine ......................................... 5-1
Starting a warm engine .................. 5-2
Shifting ........................................... 5-2
Engine break-in .............................. 5-3
Parking ........................................... 5-4
PERIODIC MAINTENANCE AND
MINOR REPAIR................................. 6-1
PERIODIC MAINTENANCE ........... 6-1
Periodic maintenance chart for the
emission control system ............. 6-2
General maintenance and
lubrication chart .......................... 6-3
Checking the spark plug ................. 6-5
Engine oil ....................................... 6-6
Cleaning the air filter element ........ 6-8
Cleaning the spark arrester ............ 6-9
Adjusting the carburetor ............... 6-10
Adjusting the engine idling
speed ........................................ 6-11
Adjusting the throttle cable free
play ........................................... 6-11
Valve clearance ............................ 6-12
Tires ............................................. 6-12
Spoke wheels ............................... 6-14
Accessories and replacement
parts .......................................... 6-14Adjusting the brake lever free
play ........................................... 6-14
Adjusting the brake pedal free
play ........................................... 6-15
Checking the front and rear
brake shoes .............................. 6-16
Drive chain slack .......................... 6-16
Cleaning and lubricating the
drive chain ................................ 6-18
Checking and lubricating the
cables ....................................... 6-19
Checking and lubricating the
throttle grip and cable ............... 6-19
Checking and lubricating the
brake and shift pedals .............. 6-19
Checking and lubricating the
brake lever ................................ 6-20
Checking and lubricating the
sidestand .................................. 6-20
Lubricating the swingarm
pivots ........................................ 6-20
Checking the front fork ................. 6-21
Checking the steering .................. 6-21
Checking the wheel bearings ....... 6-22
Battery ......................................... 6-22
Replacing the fuse ....................... 6-24
Supporting the motorcycle ........... 6-25
Front wheel .................................. 6-25
Rear wheel ................................... 6-27
Troubleshooting ........................... 6-29
Troubleshooting chart .................. 6-30U1P681E0.book Page 1 Tuesday, April 18, 2006 2:38 PM

DESCRIPTION
2-2
2
EAU10420
Right view
4 532 1
1. Seat (page 3-7)
2. Fuel tank cap (page 3-3)
3. Spark plug cap (page 6-5)
4. Brake pedal (page 3-3)
5. Engine oil filler cap (page 6-6)U1P681E0.book Page 2 Tuesday, April 18, 2006 2:38 PM

DESCRIPTION
2-3
2
EAU10430
Controls and instruments
14
5 2
6 3
1. Left handlebar switch (page 3-1)
2. Starter (choke) lever (page 3-6)
3. Main switch (page 3-1)
4. Brake lever (page 3-3)
5. Throttle grip (page 6-11)
6. Right handlebar switch (page 3-1)
U1P681E0.book Page 3 Tuesday, April 18, 2006 2:38 PM

INSTRUMENT AND CONTROL FUNCTIONS
3-3
3
EAU12890
Brake lever The brake lever is located at the right
handlebar grip. To apply the front
brake, pull the lever toward the handle-
bar grip.
EAU12941
Brake pedal The brake pedal is on the right side of
the motorcycle. To apply the rear
brake, press down on the brake pedal.
EAU13180
Fuel tank cap To remove the fuel tank cap, turn it
counterclockwise, and then pull it off.
To install the fuel tank cap, insert it into
the tank opening, and then turn it clock-
wise.
WARNING
EWA11090
Make sure that the fuel tank cap isproperly closed before riding.
1. Brake lever
1
1. Brake pedal
1
1. Fuel tank cap
1
U1P681E0.book Page 3 Tuesday, April 18, 2006 2:38 PM

INSTRUMENT AND CONTROL FUNCTIONS
3-9
3
With the engine turned off:
1. Make sure that the engine stop switch is set to “
”.
2. Turn the key to “ON”.
3. Shift the transmission into gear.
4. Keep the front or rear brake applied.
5. Push the start switch.
Does the engine start?
The neutral switch may be defective.
The motorcycle should not be ridden until
checked by a Yamaha dealer.
6. Shift the transmission into the neutral position.
7. Push the start switch.
Does the engine start?
The neutral switch may be defective.
The motorcycle should not be ridden until
checked by a Yamaha dealer.
YES
NOTE:
a warmed-up engine.
NO
The system is OK. The motorcycle can be ridden.
YES
NO
This check is most reliable if performed with
U1P681E0.book Page 9 Tuesday, April 18, 2006 2:38 PM

PRE-OPERATION CHECKS
4-2
4
EAU15605
Pre-operation check list
ITEM CHECKS PAGE
FuelCheck fuel level in fuel tank.
Refuel if necessary.
Check fuel line for leakage.3-4
Engine oilCheck oil level in engine.
If necessary, add recommended oil to specified level.
Check vehicle for oil leakage.6-6
Front brakeCheck operation.
Lubricate cable if necessary.
Check lever free play.
Adjust if necessary.6-14, 6-16
Rear brakeCheck operation.
Check pedal free play.
Adjust if necessary.6-15, 6-16
Throttle gripMake sure that operation is smooth.
Check cable free play.
If necessary, have Yamaha dealer adjust cable free play and lubricate cable and
grip housing.6-11, 6-19
Control cablesMake sure that operation is smooth.
Lubricate if necessary.6-19
Drive chainCheck chain slack.
Adjust if necessary.
Check chain condition.
Lubricate if necessary.6-16, 6-18
Wheels and tiresCheck for damage.
Check tire condition and tread depth.
Check air pressure.
Correct if necessary.6-12, 6-14
Shift pedalMake sure that operation is smooth.
Correct if necessary.6-19
U1P681E0.book Page 2 Tuesday, April 18, 2006 2:38 PM

PRE-OPERATION CHECKS
4-3
4
Brake pedalMake sure that operation is smooth.
Lubricate pedal pivoting point if necessary.6-19
Brake leverMake sure that operation is smooth.
Lubricate lever pivoting point if necessary.6-20
SidestandMake sure that operation is smooth.
Lubricate pivot if necessary.6-20
Chassis fastenersMake sure that all nuts, bolts and screws are properly tightened.
Tighten if necessary.—
Engine stop switchCheck operation.3-1 ITEM CHECKS PAGE
U1P681E0.book Page 3 Tuesday, April 18, 2006 2:38 PM

OPERATION AND IMPORTANT RIDING POINTS
5-3
5
CAUTION:
ECA15460
Always close the throttle before
shifting gears, otherwise damage to
the engine and drive train may re-sult.
3. Open the throttle gradually.
4. Once the motorcycle has reached
a speed high enough to change
gears, close the throttle.
5. Shift into second gear and release
the shift pedal.
6. Open the throttle gradually.
7. Follow the same procedure when
shifting to the next higher gear.
EAU16710
To decelerate
1. Close the throttle and apply both
the front and the rear brakes to
slow the motorcycle.
2. Downshift through the gears and
shift the transmission into the neu-
tral position when the motorcycle
is almost completely stopped.
EAU39920
Engine break-in There is never a more important period
in the life of your engine than the first 5
hours of riding. It is also important to ac-
custom the rider to the motorcycle dur-
ing this time. Please read the following
information carefully.
Since the engine is brand new, do not
put an excessive load on it for the first 5
hours of operation. The various parts in
the engine wear and polish themselves
to the correct operating clearances.
During this period, prolonged full-throt-
tle operation or any condition that might
result in engine overheating must be
avoided. However, momentary full-
throttle operation under load (i.e., two
to three seconds maximum) does not
harm the engine. Each full-throttle ac-
celeration should be followed with a
substantial rest period for the engine.
To allow the engine to cool down from
the temporary buildup of heat, cruise at
a lower engine speed.
After the first 5 hours of operation, thor-
oughly check the motorcycle for loose
parts, oil leakage and any other prob-
lems. Be sure to inspect and make ad-justments thoroughly, especially cable
and drive chain slack and loose
spokes. In addition, check all fittings
and fasteners for looseness, and tight-
en if necessary.
CAUTION:
ECA10270
If any engine trouble should occur
during the engine break-in period,
immediately have a Yamaha dealercheck the vehicle.
U1P681E0.book Page 3 Tuesday, April 18, 2006 2:38 PM