2007 YAMAHA RHINO 660 air filter

8-67 1. Air filter frame 2. Sponge material
3. Element retaining plate
1. Armature de filtre à air 2.Élément en mousse
3. Plaque de retenue de l’élément
1. Bastidor del filtro de aire 2. Material esponjoso
3. Placa de retención del filtro
5. Remove the sponge material from its frame.
6. Wash the sponge material gently but thor-
oughly in solvent.
WARNING
Always use parts cleaning solvent to clean the
sponge material. Never use low flash point sol-
vents or gasoline to clean the sponge material
because the engine could catch fire or ex-
plode.7. Squeeze the excess solvent out of the
sponge material and let it dry.CAUTION:_ Do not twist the sponge material when squeez-
ing it. _
EE.book Page 67 Friday, October 6, 2006 3:36 PM

8-69 1. Crankcase breather hose
1. Durite de mise à l’air du carter moteur
1. Tubo respiradero del cárter
8. Check the sponge material and replace it if
damaged.
9. Thoroughly apply Yamaha foam air filter oil or
other quality liquid foam air filter oil (not spray
type) to the sponge material.NOTE:_ The sponge material should be wet but not drip-
ping. _10. Pull the sponge material over its frame.
11. Install the air filter element.
12. Install the air filter case cover and be sure the
crankcase breather hose is connected.
13. Install the console.
14. Install the seats.
EE.book Page 69 Friday, October 6, 2006 3:36 PM

8-71
NOTE:_ The air filter element should be cleaned every 20–
40 hours. It should be cleaned and lubricated more
often if the vehicle is operated in extremely dusty
areas. Each time air filter element maintenance is
performed, check the air inlet to the air filter case
for obstructions. Check the air filter element rubber
joint to the carburetor and manifold fittings for an
airtight seal. Tighten all fittings securely to avoid
the possibility of unfiltered air entering the engine. _CAUTION:_ Never operate the engine with the air filter ele-
ment removed. This will allow unfiltered air to
enter, causing rapid engine wear and possible
engine damage. Additionally, operation with-
out the air filter element will affect carburetor
jetting with subsequent poor performance and
possible engine overheating.
EE.book Page 71 Friday, October 6, 2006 3:36 PM

10-3
Quantity:
Without oil filter cartridge replacement 1.90 L (1.67 Imp qt, 2.01 US qt)
With oil filter cartridge replacement 2.00 L (1.76 Imp qt, 2.11 US qt)
Final gear case oil:
Type SAE80 API GL-4 Hypoid gear oil
Quantity 0.25 L (0.22 Imp qt, 0.26 US qt)
Differential gear case oil:
Type SAE80 API GL-5 Hypoid gear oil
Quantity 0.32 L (0.28 Imp qt, 0.34 US qt)
Radiator capacity (including all routes): 2.50 L (2.20 Imp qt, 2.64 US qt)
Air filter:
Engine Wet element
Intake duct Dry element
Fuel:
Type Regular unleaded gasoline only with a
research octane number of 91 or higher
Fuel tank capacity 30.0 L (6.60 lmp gal, 7.93 US gal)
Carburetor:
Type/quantity BSR42/1
Manufacturer MIKUNIModel YXR66FSEW
EE.book Page 3 Friday, October 6, 2006 3:36 PM