PERIODIC MAINTENANCE AND MINOR REPAIR
6-4
2
3
4
5
67
8
9
10
*
Tires
Check tread depth and for damage.
Replace if necessary.
Check air pressure.
Correct if necessary.
√√√√ √
11
*
Wheel bearings
Check bearing for looseness or damage.
√√√√
12
*
Steering bearings
Check bearing play and steering for roughness.
√√√√√
Lubricate with lithium-soap-based grease. Every 24000 km
13
*
Chassis fasteners
Make sure that all nuts, bolts and screws are properly
tightened.
√√√√ √
14
Sidestand, centerstand
Check operation.
Lubricate.
√√√√ √
15
*
Sidestand switch
Check operation.
√√√√√ √
16
*
Front fork
Check operation and for oil leakage.
√√√√
17
*
Shock absorber assem-
bly
Check operation and shock absorber for oil leakage.
√√√√
18
*
Fuel injection
Check engine idle speed.
√√√√√ √
19
Engine oil
Change. (See page 6-9.)
Check oil level and vehicle for oil leakage.
√
Every 3000 km
20
*
Engine oil strainer
Clean.
√
21
Final transmission oil
Check vehicle for oil leakage.
√√ √
Change.
√√√
22
*
V-belt
Replace. Every 18000 km
23
*
Front and rear brake
switches
Check operation.
√√√√√ √
24
Moving parts and cables
Lubricate.
√√√√ √
25
*
Throttle grip housing
and cable
Check operation and free play.
Adjust the throttle cable free play if necessary.
Lubricate the throttle grip housing and cable.
√√√√ √
NO. ITEM CHECK OR MAINTENANCE JOBODOMETER READING (
×
1000 km)
ANNUAL
CHECK
1 6 12 18 24
SCOOTER CARE AND STORAGE
7-2
1
2
3
4
5
6
7
8
9thinner, fuel (gasoline), rust re-
movers or inhibitors, brake flu-
id, antifreeze or electrolyte.
Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
electric components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.
For scooters equipped with a
windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning com-
pounds for plastic may leave
scratches on the windshield.
Test the product on a small hid-
den part of the windshield to
make sure that it does not leave
any marks. If the windshield is
scratched, use a quality plastic
polishing compound after
washing.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.
After riding in the rain, near the sea oron salt-sprayed roadsSince sea salt or salt sprayed on the
roads during winter are extremely cor-
rosive in combination with water, carry
out the following steps after each ride in
the rain, near the sea or on
salt-sprayed roads.NOTE:
Salt sprayed on roads in the winter may
remain well into spring.
1. Clean the scooter with cold water
and a mild detergent after the en-
gine has cooled down.
CAUTION:
ECA10790
Do not use warm water since it in-
creases the corrosive action of the
salt.
2. Apply a corrosion protection spray
on all metal, including chrome- and
nickel-plated, surfaces to prevent
corrosion.
After cleaning
1. Dry the scooter with a chamois or
an absorbing cloth.
2. Use a chrome polish to shine
chrome, aluminum and stain-
less-steel parts, including the ex-
haust system. (Even the thermally
induced discoloring of stain-
less-steel exhaust systems can be
removed through polishing.)
3. To prevent corrosion, it is recom-
mended to apply a corrosion pro-
tection spray on all metal,
including chrome- and nickel-plat-
ed, surfaces.
4. Use spray oil as a universal clean-
er to remove any remaining dirt.
5. Touch up minor paint damage
caused by stones, etc.
6. Wax all painted surfaces.
7. Let the scooter dry completely be-
fore storing or covering it.
SPECIFICATIONS
8-2
1
2
3
4
5
6
7
8
9
Trail:
90.0 mm (3.54 in)
Front tire:
Type:
Tubeless
Size:
110/70-12 47L
Manufacturer/model:
CHENG SHIN / C-992N
Rear tire:
Type:
Tubeless
Size:
120/70-12 58L
Manufacturer/model:
CHENG SHIN / C-6007
Maximum load:
172 kg (379 lb)
* (Total weight of rider, passenger, cargo
and accessories)
Tire air pressure (measured on cold
tires):
Loading condition:
0–90 kg (0–198 lb)
Front:
175 kPa (25 psi) (1.75 kgf/cm
2
)
Rear:
200 kPa (29 psi) (2.00 kgf/cm
2
)
Loading condition:
90–172 kg (198–379 lb)
Front:
200 kPa (29 psi) (2.00 kgf/cm
2
)Rear:
225 kPa (33 psi) (2.25 kgf/cm
2
)
Front wheel:
Wheel type:
Cast wheel
Rim size:
J12 X MT2.75
Rear wheel:
Wheel type:
Cast wheel
Rim size:
J12 X MT3.00
Front brake:
Type:
Single disc brake
Operation:
Right hand operation
Recommended fluid:
DOT 4
Rear brake:
Type:
Drum brake
Operation:
Left hand operation
Front suspension:
Type:
Telescopic fork
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel:
78.0 mm (3.07 in)
Rear suspension:
Type:
Unit swing
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel:
95.5 mm (3.76 in)
Electrical system:
Ignition system:
Transistorized coil ignition (digital)
Charging system:
AC magneto
Battery:
Model:
MF (YT7B-BS)
Voltage, capacity:
12 V, 6.5 Ah
Headlight:
Bulb type:
Halogen bulb
Bulb voltage, wattage
×
quantity:
Headlight:
12 V, 60 W/55.0 W
×
1
Tail/brake light:
12 V, 5.0 W/21.0 W
×
1
Front turn signal light:
12 V, 10.0 W
×
2
Rear turn signal light:
12 V, 10.0 W
×
2
Auxiliary light:
12 V, 5.0 W
×
2
License plate light:
12 V, 5.0 W
×
1
