2007 YAMAHA CYGNUS 125 lock

3-1
2
34
5
6
7
8
9

INSTRUMENT AND CONTROL FUNCTIONS
EAUU0061
Main switch
The main switch controls the ignition
and lighting systems. The various main
switch positions are described below.
NOTE:

The main switch is equipped with a key-
hole cover. (See page 3-2.)
EAUT1971
ON
All electrical circuits are supplied with
power; the meter lighting, taillight, and
auxiliary lights come on, and the engine
can be started. The key cannot be re-
moved.
NOTE:

The headlight comes on automaticallywhen the engine is started and stays on
until the key is turned to “OFF” or the
sidestand is moved down.
EAU10660
OFF
All electrical systems are off. The key
can be removed.
EAU10680
LOCK
The steering is locked, and all electrical
systems are off. The key can be re-
moved.
To lock the steering
1. Turn the handlebars all the way tothe left.
2. Push the key in from the “OFF” po-
sition, and then turn it to “LOCK”
while still pushing it.
3. Remove the key.
To unlock the steering
Push the key in, and then turn it to
“OFF” while still pushing it.
WARNING

EWA10060
Never turn the key to “OFF” or
“LOCK” while the vehicle is moving,
otherwise the electrical systems will
be switched off, which may result in
loss of control or an accident. Make
ZAUM00**

1. Push.
ZAUM00**
1

1. Turn.
2. Release.
12
ZAUM00**

INSTRUMENT AND CONTROL FUNCTIONS
3-2
1
2
3
4
5
6
7
8
9sure that the vehicle is stopped be-
fore turning the key to “OFF” or

“LOCK”.
EAUT2111
Keyhole cover
To open the keyhole cover
Insert the key bow into the keyhole cov-
er receptacle as shown, and then turn
the key to the right to open the cover.
To close the keyhole cover
Push the keyhole cover lever inward
and the keyhole cover will close.

EAU11003
Indicator and warning lights
EAU11020
Turn signal indicator light “”
This indicator light flashes when the
turn signal switch is pushed to the left or
right.
EAU11080
High beam indicator light “”
This indicator light comes on when the
high beam of the headlight is switched
on.
1. Keyhole cover lever
ZAUM00**
1

1. High beam indicator light “ ”
2. Turn signal indicator light “ ”
3. Engine trouble warning light “ ”
ZAUM00**
RESET
SELECT
1
2
3

INSTRUMENT AND CONTROL FUNCTIONS
3-3
2
34
5
6
7
8
9

EAUT1930
Engine trouble warning light “”
This warning light flashes when an
electrical circuit monitoring the engine
is defective. When this occurs, have a
Yamaha dealer check the self-diagno-
sis system.
The electrical circuit of the warning light
can be checked by turning the key to
“ON”. If the warning light does not come
on for a few seconds, then go off, have
a Yamaha dealer check the electrical
circuit.
EAU11601
Speedometer
The speedometer shows the riding
speed.
When the key is turned to “ON”, the
speedometer needle will sweep once
across the speed range and then return
to zero in order to test the electrical cir-
cuit.
EAUT1952
Multi-function display
WARNING

EWA14430
Be sure to stop the vehicle before
making any setting changes to the
multi-function display.
The multi-function display is equipped
with the following:

an odometer (which shows the to-
tal distance traveled)
1. Speedometer
ZAUM00**
RESET
SELECT
1
1. Tripmeter
2. Oil change indicator “ ”
3. Odometer
4. Fuel meter
5. “RESET” button
6. “SELECT” button
7. Clock
ZAUM00**
RESET
SELECT
1
2
3
4
5
6
7

INSTRUMENT AND CONTROL FUNCTIONS
3-4
1
2
3
4
5
6
7
8
9


a tripmeter (which shows the dis-
tance traveled since it was last set
to zero)

an oil change tripmeter (which
shows the distance traveled since
the last engine oil change)

an oil change indicator (which
flashes when the engine oil should
be changed)

a clock

a fuel meter
NOTE:


When the key is turned to “ON”, all
segments of the display come on
for a few seconds. During this
time, the multi-function display is
performing a self-test.

Be sure to turn the key to “ON” be-
fore using the “SELECT” and “RE-
SET” buttons.
Odometer, tripmeter and oil change
tripmeter modes
Pushing the “SELECT” button switches
the display among the odometer mode
“ODO”, the tripmeter mode “TRIP” and
the oil change tripmeter “OIL CHANGE
TRIP” in the following order:ODO
→
TRIP
→
OIL CHANGE TRIP
→
ODO
Odometer
NOTE:

If the odometer indicates “-----”, have a
Yamaha dealer check the multi-func-
tion display, as it may be faulty.
Tripmeter
To reset the tripmeter, select it by push-
ing the “SELECT” button until “TRIP” is
displayed, and then push the “RESET”
button at least 1 second.
NOTE:

If the tripmeter indicates “-----”, have a
Yamaha dealer check the multi-func-
tion display, as it may be faulty.
Oil change tripmeter
To reset the oil change tripmeter, select
it by pushing the “SELECT” button until
“OIL CHANGE TRIP” is displayed, and
then push the “RESET” button at least
3 seconds. After resetting the oil
change tripmeter, “ODO” will be dis-
played.
NOTE:

If the “SELECT” button is pushed again
or the “SELECT” button hasn’t been
pushed within 10 seconds, the oil
change tripmeter will keep counting
and “ODO” will be displayed.
Oil change indicator
Oil change indicator “”
This indicator flashes at the initial 1000
km (600 mi), then at every 3000 km
(1800 mi) thereafter to indicate that the
engine oil should be changed.
After changing the engine oil, reset the
oil change tripmeter.
If the engine oil is changed before the
oil change indicator flashes (i.e. before
the periodic oil change interval has
been reached), the oil change tripmeter
must be reset after the oil change for
the next periodic oil change to be indi-
cated at the correct time.
NOTE:


If the oil change tripmeter is reset
before the initial 1000 km (600 mi),
the next periodic oil change inter-

INSTRUMENT AND CONTROL FUNCTIONS
3-5
2
34
5
6
7
8
9
val will be at every 3000 km (1800
mi) thereafter.


If the oil change tripmeter indicates
“-----”, have a Yamaha dealer
check the multi-function display,
as it may be faulty.
Clock
To set the clock:
1. Push the “SELECT” button and
“RESET” button together for at
least two seconds.
2. When the hour digits start flashing,
push the “SELECT” button to set
the hours.
3. Push the “RESET” button, and the
first minute digit will start flashing.
4. Push the “SELECT” button to set
the first minute digit.
5. Push the “RESET” button and the
second minute digit will start flash-
ing.
6. Push the “SELECT” button to set
the second minute digit.
7. Push the “RESET” button and then
release it to start the clock.
Fuel meter
The fuel meter indicates the amount of
fuel in the fuel tank. The display seg-
ments of the fuel meter disappear to-
wards “E” (Empty) as the fuel level
decreases. When “ ” starts flashing,
refuel as soon as possible. When the
key is turned to “ON”, all of the display
segments of the fuel meter will appear
for a few seconds, and then shown ac-
tual fuel level.

EAU12347
Handlebar switches
Left
1. Dimmer switch “ / ”
2. Turn signal switch “ / ”
3. Horn switch “ ”
ZAUM00**
3 1
2

INSTRUMENT AND CONTROL FUNCTIONS
3-7
2
34
5
6
7
8
9

EAU12950
Rear brake lever
The rear brake lever is located on the
left handlebar grip. To apply the rear
brake, pull this lever toward the handle-
bar grip.
EAU13071
Fuel tank cap
To open the fuel tank cap
Open the fuel tank cap lock cover, in-
sert the key into the lock, and then turn
it 1/4 turn clockwise. The lock will be re-
leased and the fuel tank cap can be
opened.
To close the fuel tank cap
1. Push the fuel tank cap into position
with the key inserted in the lock.
2. Turn the key counterclockwise to
the original position, remove it, and
then close the lock cover.
NOTE:

The fuel tank cap cannot be closed un-less the key is in the lock. In addition,
the key cannot be removed if the cap is
not properly closed and locked.
WARNING

EWA11090
Make sure that the fuel tank cap is
properly closed before riding.
1. Rear brake lever
ZAUM00**
1

1. Fuel tank cap lock cover
ZAUM00**
1

INSTRUMENT AND CONTROL FUNCTIONS
3-9
2
34
5
6
7
8
9

EAU13441
Catalytic converter
This vehicle is equipped with catalytic
converters in the exhaust system.
WARNING

EWA10860
The exhaust system is hot after op-
eration. Make sure that the exhaust
system has cooled down before do-
ing any maintenance work.
CAUTION:

ECA10700
The following precautions must be
observed to prevent a fire hazard or
other damages.

Use only unleaded gasoline.
The use of leaded gasoline will
cause unrepairable damage to
the catalytic converter.

Never park the vehicle near pos-
sible fire hazards such as grass
or other materials that easily
burn.

Do not allow the engine to idle
too long.
EAU13680
Kickstarter
To start the engine, fold out the kick-
starter lever, move it down lightly with
your foot until the gears engage, and
then push it down smoothly but force-
fully.
EAUT1502
Seat
To open the seat
1. Place the scooter on the center-
stand.
2. Insert the key into the main switch,
and then turn it counterclockwise
to the first “OPEN” position. If the
main switch is in the “LOCK” posi-
tion, turn the key counterclockwise
to the second “OPEN” position.
NOTE:

Do not push inward when turning the
key from “OFF” to “OPEN” or from
“LOCK” to “OPEN”.
3. Fold the seat up.
1. Kickstarter
ZAUM00**
1
ZAUM00**

INSTRUMENT AND CONTROL FUNCTIONS
3-10
1
2
3
4
5
6
7
8
9To close the seat
1. Fold the seat down, and then push
it down to lock it in place.
2. Remove the key from the main
switch if the scooter will be left un-
attended.
NOTE:

Make sure that the seat is properly se-
cured before riding.
EAUT1711
Storage compartments
Front storage compartment
WARNING

EWA11190

Do not exceed the load limit of
1.5 kg (3.3 lb) for the front stor-
age compartment.

Do not exceed the maximum
load of 172 kg (379 lb) for the ve-
hicle.Rear storage compartment
The rear storage compartment is locat-
ed under the seat. (See page 3-9.)
CAUTION:

ECAT1030
Keep the following points in mind
when using the storage compart-
ment.

Since the storage compartment
accumulates heat when ex-
posed to the sun, do not store
anything susceptible to heat in-
side it.

To avoid humidity from spread-
ing through the storage com-
partment, wrap wet articles in a
plastic bag before storing them
1. Front storage compartment
ZAUM00**
1
1. Rear storage compartment
ZAUM00**
1