2007 TOYOTA TUNDRA clock

4312007 TUNDRA from Jul. ’07 Prod. (OM34463U)
XS10071a
Before using the box, lift up the rear
seats. (For detailed information, see
“—Raising rear seat cushion (Double
cab models)” on page 59 in Section
13.)
To open the storage box, turn the
knobs “OPEN” direction indicated by
the arrow and open the lid as shown in
the illustration.
The storage box can be removed. For
detailed information, see “—Removing the
storage box” on page 431 in this Section.
CAUTION
To reduce the chance of injury in
case of an accident or a sudden stop,
always keep the storage box closed
and locked while driving.
NOTICE
To prevent damage to the storage
box, avoid putting heavy loads on the
storage box lids.
XS10087
To remove the storage box:1. Remove the storage box lids.
2. Remove the knobs by turning them counterclockwise.
3. Remove the storage box.
Storage box (on some Double
cab models) — R emo vin g th e st o rag e bo x

5032007 TUNDRA from Jul. ’07 Prod. (OM34463U)
LS40036
Turn the jack joint by hand.
To rem ov e: Tur n the joint in direction
1 until the jack is free.
To store: Turn the joint in direction 2
until the jack is fi rmly secured to pre-
vent it flying forward during a collision
or sudden braking.
XS40006
To remove the temporary spare tire:
1. Put a jack handle extension and jack handle end together as shown
in the illustration.
1 Jack handle extension No.1
2 Jack handle extension No.2
3 Wheel nut wrench
CAUTION
Make sure they are each securely
fixed.
XS40008
2. Insert the end of the jack handle
extension No.1 into the lowering
screw and turn it counterclock-
wise.
3. After the tire is lowered completely to the ground, remove the holding
bracket.
When storing the temporary spare
tire, put it in place with the outer side
of the wheel facing up. Then secure
the tire, taking care that the tire goes
straight up without catching on any
other part, to prevent it from flying for-
ward during a collision or sudden
braking.

5042007 TUNDRA from Jul. ’07 Prod. (OM34463U)
Keep winding until three clicks are
heard.
XS40011
2. Block the wheel diagonally op-posite the flat tire to keep the
vehicle from rolling when it is
jacked up.
When blocking the wheel, place a
wheel block in front of one of the front
wheels or behind one of the rear
wheels.
XS40015b
3. Loosen all the wheel nuts.
Always loosen the wheel nuts before
raising the vehicle.
Turn the wheel nuts counterclockwise
to loosen. To get maximum leverage,
fit the wrench to the nut so that the
handle is on the right side, as shown
above. Grab the wrench near the end
of the handle and pull up on the han-
dle. Be careful that the wrench does
not slip off the nut.
Do not remove the nuts yet—just un-
screw them about one −half turn.
—Blocking the wheel —Loosening wheel nuts

5062007 TUNDRA from Jul. ’07 Prod. (OM34463U)
LS40037
Front of
vehicle
5. After making sure that no one is in the vehicle, as the jack
touches the vehicle and begins
to lift, doublecheck that it is
properly positioned.
Rear side only—
When positioning the jack under the
rear axle housing, make sure the
groove on the top of the jack fits with
the rear axle housing.
XS40017a
6. After making sure that no one is in the vehicle, raise it high
enough so that the temporary
spare tire can be installed.
Remember you will need more ground
clearance when putting on the tempo-
rary spare tire than when removing
the flat tire. To raise the vehicl
e, insert the jack
handle end with the extension into the
jack (it is a loose fit) and turn it clock-
wise with the handle. As the jack
touches the vehicle and begins to lift,
double −check that it is properly posi-
tioned.
CAUTION
Never get under the vehicle when
the vehicle is supported by the
jack alone.
—Raising your vehicle

5082007 TUNDRA from Jul. ’07 Prod. (OM34463U)
CAUTION
Never use oil or grease on the
bolts or nuts. Doing so may lead
to overtightening the nuts and
damaging the bolts. The nuts
may loosen and the wheels may
fall off, which could cause a seri-
ous accident. If there is oil or
grease on any bolt or nut, clean
it.
XS40021
9. Lower the vehicle completelyand tighten the wheel nuts.
Turn the jack handle end with the ex-
tension counterclockwise with handle
to lower the vehicle, making sure the
handle remains firmly fitted onto the
jack handle extension.
Use only the wheel nut wrench and
turn it clockwise to tighten the nuts.
Do not use other tools or any addition-
al leverage other than your hands,
such as a hammer, pipe or your foot.
Make sure the wrench is securely en-
gaged over the nut. Tighten each nut a little at a time in
the order shown. Repeat the process
until all the nuts are tight.
CAUTION

When lowering the vehicle,
make sure all portions of your
body and all other persons
around will not be injured as
the vehicle is lowered to the
ground.
—Lowering your vehicle

5482007 TUNDRA from Jul. ’07 Prod. (OM34463U)
XS72005
If hot
O.K.OpenIf cold
O.K.
If hot
add If cold
add
Close
Check the fluid level through the reser-
voir. If necessary, add automatic trans-
mission fluid DEXRONII or III.
If the vehicle has been driven around 80
km/h (50 mph) for 20 minutes (a little
more in frigid temperatures), the fluid is
hot (60 C—80 C or 140 F—175 F). You
may also check the level when the fluid
is cold (about room temperature,
10 C—30 C or 50 F—85 F) if the engine
has not been run for about five hours. Clean all dirt from the outside of the res-
ervoir tank and look at the fluid level. If
the fluid is cold, the level should be in the
“COLD” range. Similarly, if it is hot, the
fluid level should be in the “HOT” range.
If the level is at the low side of either
range, add automatic transmission fluid
DEXRON
II or III to bring the level within
the range.
To remove the reservoir cap, turn it coun-
terclockwise and lift up. To reinstall it,
turn it clockwise. After replacing the reser-
voir cap, visually check the steering box
case, vane pump and hose connections
for leaks or damage.
CAUTION
The reservoir tank may be hot so be
careful not to burn yourself.
NOTICE
Avoid overfilling, or the power steer-
ing could be damaged.
XS72011
Checking power steering fluid Checking tire inflation
pressure

5652007 TUNDRA from Jul. ’07 Prod. (OM34463U)
Light bulbsBulbNo.WTy p e
Front personal
lights—5D
Rear personal
lights—5D
Glove box light741.2D
Foot light—1.4D
Door courtesy
light1685D
A: HB3 halogen bulbs
B: H11 halogen bulbs
C: H10 halogen bulbs
D: Wedge base bulbs (clear)
E: Wedge base bulbs (amber)
XS73007
1. Open the hood. Unplug the connector
while depressing the lock release.
If the connector is tight, wiggle it.
If additional space is required to access
the connector, move the battery rearward
by loosening the battery hold −down clamp.
XS73008
2. Turn the bulb base counterclockwise
and remove it.
—H ead lig h t s (h ig h beam)

5672007 TUNDRA from Jul. ’07 Prod. (OM34463U)
XS73004
2. Turn the bulb base counterclockwiseand remove it.
XS73005
3. Plug in a new bulb install it into themounting hole.
Aiming is not necessary after replacing
the bulb. When aiming adjustment is nec-
essary, contact your Toyota dealer.
XS73006
4. Install the connector to the bulb.