2007 TOYOTA LAND CRUISER change time

cv
Screen animation
When the “Screen Animation” feature is
turned on, some switches and screens
become animated. (e.g.: change map
guidance on the map screen)
To turn the “Screen Animation” mode on:
1. Push the
“MENU” button.
2. Touch the “Setup” switch. Then
touch
switch three times to display
page 4 of the “Setup” screen.
3. Touch the “On” switch of “Screen
Animation” and touch the
“OK” switch.

cviii
Maintenance information
This system informs you when to replace
certain parts or components and shows
dealer information (if registered) on the
screen. (See “Information items” on
page cix.) When the navigation system
begins operating after either the informa-
tion item’s preset data arrives or the
driving distance reaches a predeter-
mined setting, the “Information” screen
will be displayed. This screen will appear
every time the system is turned on until
you touch the
“Do not display this
message again”
switch.
To prevent this information screen from be-
ing displayed again, touch the
“Do not
display this message again”
switch.1. Push the
“INFO” button to display
the “Information Menu” screen and
touch the
“Maintenance” switch.
5u004
2. Touch the desired icon and input the
conditions.
Notice of “Date”: You can input the next
maintenance date.
Notice of “Distance”: You can input the
driving distance until the next maintenance
check.
When you touch the
switch on the
“Maintenance” screen, the screen changes
to the “Personal Event” screen. Touch the
keys to input the desired name and then in-
put conditions.
After you input the date and/or distance,
touch the
“OK” switch. The screen then
returns to the “Maintenance” screen.
The following switches appear.
“Delete All”: To cancel all conditions which
have been inputted.

cxiii
(d) Set as destination
Touch the “Enter ” switch on the “Set
Dealer” screen. The screen changes and
displays the map location of the regis-
tered dealer and the “Route Preference”.
(See
“ — Entering Destination” on page xlviii.)
Calendar with memo
This system informs you of a memo entry.
At the specified date, the memo informa-
tion will be displayed when the naviga-
tion system is in operation. The memo in-
formation screen will appear every time
the system is turned on. To disable this
screen, touch the
“Do not display
this message again”
switch.1. Push the
“INFO” button to display
the “Information Menu” screen.
5u004
2. Touch the “Calendar” switch to dis-
play the “Calendar” screen.

cl If manual switching of air intake is de-
sired
UNX506
The air intake control button is used to switch
the air intake between the OUTSIDE AIR
mode and RECIRCULATED AIR mode.
With the button in the OUTSIDE AIR mode,
the OUTSIDE AIR mode indicator light will
come on and the system will take fresh out-
side air into the vehicle.
If quick circulation of cooled air is desired,
push the air intake control button for RECIR-
CULATED AIR. The RECIRCULATED AIR
mode indicator light will come on.
For normal use, it is best to keep the air in-
take control button set to OUTSIDE AIR
mode. If recirculated air is used during heat-
ing, the windows will fog up more easily.If the engine coolant temperature becomes
extremely high, the RECIRCULATED AIR
mode is automatically selected. This is not
a malfunction. When the engine coolant
temperature is lowered, the previous mode
resumes.
In the following cases, the RECIRCULATED
mode may change to the OUTSIDE AIR
mode automatically to prevent interior fog.
When the outside temperature becomes
lower than 4C (39F).
When the air conditioning compressor
malfunctions.
When the air conditioning cooler refriger-
ant decreases.If manual onoff of the air conditioning is
desired
Push the “A/C” switch to turn the air condi-
tioning on and push it again to turn the air
conditioning off. If you turn off the air condi-
tioning manually, the EXHAUST GAS AU-
TOMATIC mode will be cancelled.
If the outside temperature is lowered down to
around 0C (32F), the air conditioning will
turn off automatically. At this time, the indica-
tor on the A/C button is off and the EX-
HAUST GAS AUTOMATIC indicator light re-
mains on. However, the EXHAUST GAS
AUTOMATIC mode does not operate.
When the air conditioning turns on as with
the raised temperature, the EXHAUST GAS
AUTOMATIC mode resumes.
If the system is used for ventilation, heating
in dry weather or removing frost or exterior
fog on the windshield, turn the air condition-
ing off once it is no longer required. This will
improve fuel economy. The air conditioning
can be used for year−round automatic tem-
perature control including cooling and dehu-
midifying operation.

clxi
(b) Presetting a station
lxb001a
1. Tune in the desired station.
2. Touch one of the station selector
switches (16) and hold it until a beep is
heard. This sets the station to the switch
and the frequency appears on the switch.
Each switch can store FM1, FM2 and AM.
To change the preset station to a different
one, follow the same procedure.
The preset station memory is cancelled
when the power source is interrupted by bat-
tery disconnection or a blown fuse.
(c) Selecting a station
Your Toyota has an electronic tuning radio
(ETR). Tune in the desired station using one
of the following methods.
Preset tuning: Touch the switch (1−6) or
push the “
” or “” side of the “CH” button
for the station you want. The switch (1−6) is
highlighted in green and station frequency
appears on the display.
Manual tuning: Turn the “TUNE” knob brief-
ly. Each time you turn the knob, the radio will
step up or down to another frequency.
Seek tuning: Push the “
” or “” side of
the “SEEK” button and hold it until you hear
a beep. The radio will begin seeking up or
down for a station of the nearest frequency
and will stop on reception. Each time you
push the button, the stations will be
searched out one after another.
lxb001a
Scan tuning:Touch the “SCAN” switch
briefly. “SCAN” appears on the display. The
radio will find the next station up or down the
band, stay there for a few seconds, and then
scan again. To select a station, touch the
“SCAN” switch a second time.
Preset scan tuning: Touch the “SCAN”
switch and hold it until you hear a beep. “P.
SCAN” appears on the display. The radio
will tune in the next preset station up or down
the band, stay there for a few seconds, and
then move to the next preset station. To se-
lect a station, touch the “SCAN” switch a se-
cond time.

clxii
(d) RDS (Radio Data System)
Program type
lxb001a
When you touch the “TYPE ” or “TYPE
” switch on the screen, the current pro-
gram type receiving from RDS station ap-
pears on the display.
If the system receives no RDS stations, “NO
PTY” appears on the display.Each time you touch the “TYPE ” or
“TYPE ” switch, the program type
changes as in the following:
ROCK
EASY LIS (Easy listening)
CLS/JAZZ (Classical music and Jazz)
R&B (Rhythm and Blues)
INFORM (Information)
RELIGION
MISC.
ALERT (Emergency message)
lxb003a
When a program is set, “TYPE SEEK”
switch appears. Touch the switch and the
system starts to seek the station in the rele-
vant program type.
Traffic program: A station that regularly
broadcasts traffic information is auto-
matically located.
When you push the “TRAF” button, “TRAF
SEEK” appears on the display and the radio
will start seeking any traffic program station.
If any traffic program station is not found,
“NOTHING” appears and the previous mode
returns.
If the traffic program station is found, the
name for traffic program station is displayed
and “TRAF” is lit for a while until traffic an-
nouncement is received.
VI

clxiii
Radio text
lxb001a
If the system receives a radio text from RDS
station, “MSG” appears on the display.
Touch the “MSG” switch, and a text mes-
sage is displayed on the screen.
lxb005a
In case a text message is not accepted in a
screen, you can touch the “MSG” switch
and hold it to display the rest of the message.
When the system can show the station
name, “RDS” appears on the display. Each
time you touch the “MSG” switch, indication
on the display changes from the band to the
station name, a radio text in this order. After
six seconds passes, indication returns to the
band.
Radio operation (XM
satellite radio broadcast)
To listen to a satellite radio broadcast in your
vehicle, an additional genuine Toyota satel-
lite receiver and antenna must be purchased
and installed, and the subscription to the
XMsatellite radio is necessary.

clxviii
(h) If the satellite radio tuner malfunctions
When problems occur with the XM tuner, a message will appear on the display. Referring to the table below to identify the problem, take the
suggested corrective action.
ANTENNA
The XM antenna is not connected. Check whether the XM antenna cable is attached securely.
A short−circuit occurs in the antenna or the surrounding antenna cable. See a Toyota certified dealer.
UPDATING
You have not subscribed to the XM satellite radio. The radio is being updated with the latest encryp-
tion code. Contact the XM satellite radio for subscription information. When a contact is canceled,
you can choose the “CH000” and all free−to−air channels.
The premium channel you selected is not authorized. Wait for about 2 seconds until the radio returns
to the previous channel or “CH001”. If it does not change automatically, select another channel. If you
want to listen to the premium channel, contact the XM satellite radio.
NO SIGNALThe XM signal is too weak at the current location. Wait until your vehicle reaches a location with a
stronger signal.
LOADINGThe unit is acquiring audio or program information. Wait until the unit has received the information.
OFF AIRThe channel you selected is not broadcasting any programming. Select another channel.
−−−−−There is no song/program title or artist name/feature associated with the channel at that time. No ac-
tion needed.
−−−The channel you selected is no longer available. Wait for about 2 seconds until the radio returns to the
previous channel or “CH001”. If it does not change automatically, select another channel.
The XM Listener Care Center is also available on the phone, please call (800) 967−2346 during the following hours:
Monday – Saturday: 7 a.m. – 1 a.m. Sunday: 12 p.m – 12 a.m.
VI