Page 27 of 428
’07Camry_U (L/O 0608)
19
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
The engine immobilizer system is automat-
ically set when:
Vehicles with key cylinder−type ignition
switch—The key is removed from the igni-
tion switch.
Vehicles with smart key system—The igni-
tion switch is turned off.
The indicator light will start flashing to
show that the system is set.If any of the following indicator conditions
occur, contact your Toyota dealer.
The indicator light stays on except
when the theft deterrent system is set-
ting or activating. (See “Theft deterrent
system” on page 49 in this Section.)
The indicator light does not start flash-
ing under the following situations.
Vehicles with key cylinder−type ignition
switch—When the key is removed from
the ignition switch.
Vehicles with smart key system—When
the ignition switch is turned off.
The indicator light flashes inconsistent-
ly.
The engine immobilizer system is automat-
ically canceled when:
Vehicles with key cylinder−type ignition
switch—
You insert the key to the ignition switch.
Vehicles with smart key system—
You enter the vehicle carrying a key with
smart key system and press the “ENGINE
START STOP” switch (engine switch).
Even if the key battery is discharged, the
engine can be started. See “Smart key
system” on page 30 in this Section.When the system is canceled, the indica-
tor light will go off.
For your Toyota dealer to make you a
new key with built−in transponder chip,
your dealer will need your key number
and master key (vehicles with key cylin-
der−type ignition switch) or electronic key
(vehicles with smart key system). Howev-
er, there is a limit to the number of addi-
tional keys your Toyota dealer can make
for you.
NOTICE
Do not modify, remove or disas-
semble the engine immobilizer sys-
tem. If any unauthorized changes or
modifications are made, proper opera-
tion of the system cannot be guaran-
teed.
Page 28 of 428
’07Camry_U (L/O 0608)
20
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
For vehicles sold in U.S.A.
Key cylinder type ignition switch
FCC ID: MOZRI 20BTY
FCC ID: MOZRI 21BTY
Smart key system
FCC ID: NI4TMIMB 1
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and (2) this device must
accept any interference received, includ-
ing interference that may cause unde-
sired operation.
CAUTION
Changes or modifications not ex-
pressly approved by the party respon-
sible for compliance could void the
user’s authority to operate the equip-
ment.
For vehicles sold in Canada
This device complies with RSS−210 of
Industry Canada. Operation is subject to
the following two conditions:
(1) This device may not cause interfer-
ence, and (2) this device must accept
any interference, including interference
that may cause undesired operation of
the device.
Vehicles with key cylinder type ignition
switch
Vehicles with smart key system
Wireless remote control—
Page 29 of 428
’07Camry_U (L/O 0608)
21
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
1. Indicator light
2. Lock switch
3. Alarm switch
4. Unlock switch
5. Trunk opener switchThe wireless remote control function is
designed to lock or unlock all the
doors, open the trunk lid, or activate
the alarm from a distance within
approximately 1 m (3 ft.) of the vehicle.
When you operate any switch, push it
slowly and securely.
When the switch is operated, the indicator
light flashes once. If not, the battery may
be discharged. Replace the battery at the
earliest opportunity.
The wireless remote control transmitter is
an electronic component. Observe the fol-
lowing instructions in order not to cause
damage the key.
Do not leave the transmitter in places
where the temperature becomes high
such as on the dashboard.
Do not disassemble it.
Avoid knocking it hard against other
objects or dropping it.
Avoid putting it in water.
You can use up to 4 wireless remote con-
trol keys (for vehicles with key cylinder−
type ignition switch) or 5 wireless remote
control transmitters (for vehicles with
smart key system) for the same vehicle.
Contact your Toyota dealer for detailed
information.If the wireless remote control transmitter
does not actuate the doors, or does not
operate from a normal distance, or if the
indicator on the transmitter is dimmed or
does not come on:
Check for closeness to a radio trans-
mitter such as a radio station or an
airport which can interfere with normal
operation of the key.
The battery may have been consumed.
Check the battery in the key. To re-
place the battery, see “—Replacing bat-
tery” on pages 26 or 28 in this Sec-
tion.
If you lose your wireless remote control
key, contact your Toyota dealer as soon
as possible to avoid the possibility of
theft, or an accident. (See “If you lose
your keys” on page 356 in Section 4.)
It is possible to disable the wireless re-
mote control system. For details, contact
your Toyota dealer.
Page 31 of 428
’07Camry_U (L/O 0608)
23
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
Locking operation (vehicles with key cyl-
inder type ignition switch)
Unlocking operation (vehicles with key
cylinder type ignition switch)
Locking operation (vehicles with smart
key system)
Unlocking operation (vehicles with smart
key system)
To lock or unlock all the doors, push
the switches slowly and securely.
To lock: Push the lock switch. All the
doors are locked simultaneously. At this
time one beep will sound and turn signal
lights flash once.
Check to see that the doors are securely
locked.
If any of the doors is not securely closed,
or if the key is in the ignition switch (ve-
hicles with key cylinder−type ignition
switch) or key left in the vehicle (vehicles
with smart key system), locking cannot be
performed by the lock switch and a beep
will sound continuously for 10 seconds.
To stop the beep, take out the key from
the vehicle or push the unlock switch.
The answerback function (the turn signal
flash and the beep) can be disabled. For
details, contact your Toyota dealer.
—Locking and unlocking
doors
Page 32 of 428
’07Camry_U (L/O 0608)
24
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
To unlock: Push the unlock switch once to
unlock the driver ’s door alone. Pushing
the switch twice within 3 seconds unlocks
all the doors simultaneously. Each time
the unlock switch is pushed, two beeps
will sound and turn signal lights flash
twice.
This double switch operation to unlock all
doors can be changed to a single switch
operation. For details, contact your Toyota
dealer.
If the key is in the ignition (vehicles with
key cylinder−type ignition switch) or the
ignition switch is set to ACC or ON (ve-
hicles with smart key system), the vehicle
cannot be unlocked via the unlock switch.
You have 60 seconds to open a door after
using the wireless remote unlock feature.
If a door is not opened by then, all the
doors will be automatically locked again.
If the wireless remote control is used to
lock the doors near the window or door
handle, there is a possibility that the door
may not unlocked by entry function of
smart key system. Under these circum-
stances, use the wireless remote control
to unlock the doors.The automatic locking time can also be
set to 30 seconds. For details, contact
your Toyota dealer.
If the lock or unlock switch is kept
pressed in, the locking or unlocking opera-
tion is not repeated. Release the switch
and then push again.
When you unlock doors using the wireless
remote control, the illuminated entry func-
tion will be activated. (For further informa-
tion, see “Illuminated entry system” on
page 128 in Section 1−5.)
Vehicles with key cylinder type ignition
switch
Vehicles with smart key system
—Opening trunk lid
Page 33 of 428
’07Camry_U (L/O 0608)
25
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
To open the trunk lid, push and hold
the trunk opener switch of the transmit-
ter for 1 second. A long beep will
sound.
If the key is in the ignition (vehicles with
key cylinder−type ignition switch) or the
ignition switch is set at ACC or ON (ve-
hicles with smart key system), the trunk
lid cannot be opened by the trunk opener
switch.
Opening of the trunk lid with the wireless
remote control can be changed as follows.
Contact your Toyota dealer for details.
Trunk lid opens by pushing the trunk
opener switch twice in succession.
Trunk lid opens by pushing the trunk
opener switch once regardless of how
long the switch is being pressed.
Opening of the trunk lid is disabled
using the wireless remote control trans-
mitter.
Vehicles with key cylinder type ignition
switch
Vehicles with smart key system
Pushing the alarm switch for 1 second
or more blows the horn intermittently
and flashes the headlights, turn signal
lights, tail lights and interior light.
Vehicles with smart key system only—
When pushing the switch, the indicator
light flashes.
The alarm switch is used to deter vehicle
theft when you witness anyone attempting
to break into or damage your vehicle.
The alarm will last for one minute. To stop
the alarm midway, push any button on the
wireless remote control or set the ignition
switch to ON.
If the key is in the ignition (vehicles with
key cylinder−type ignition switch) or the
ignition switch is set at ACC or ON (ve-
hicles with smart key system), the alarm
does not work.
This alarm function can be disabled. For
details, contact your Toyota dealer.
—Activating alarm
Page 34 of 428
’07Camry_U (L/O 0608)
26
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
For replacement, use a CR2016 lithium
battery or equivalent.
CAUTION
Special care should be taken to pre-
vent small children from swallowing
the removed battery or components.
NOTICE
When replacing the battery, be care-
ful not to lose the components.
Replace only with the same or
equivalent type recommended by a
Toyota dealer.
Dispose of used batteries according
to the local laws.
Replace the battery by following these
procedures:
1. Open the cover using a flathead screw-
driver wrapped with plastic tape.2. Remove the module from the key
frame.
—Replacing battery
(with key cylinder type
ignition switch)
Page 35 of 428
’07Camry_U (L/O 0608)
27
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
3. Open and remove the battery case
cover using a coin.4. Take out the discharged transmitter
battery and put in a new battery with
the positive (+) side up.5. Install the battery case cover and then
install the module into the key frame.
Close the cover.
6. When pushing either switch on the
wireless key, make sure the indicator
light comes on.
NOTICE
Do not bend the terminals.
Make sure the positive side and
negative side of the battery are
faced correctly.
Do not replace the battery with wet
hands. Water may cause unexpected
rust.
Do not touch or move any compo-
nents inside the transmitter, or it
may interfere with proper operation.
Be careful not to bend the electrode
when inserting the battery and that
dust or oils do not adhere to the
case.
Close the cover securely.
