2007 SUZUKI XL7 air filter

3-14 INSTRUMENT PANEL
78J00-03E
Mode Knob
The right knob on the control panel lets
you to choose the direction of air delivery.
(Vent):
This setting directs the air through the
headliner outlets.
(Bi-Level):
This setting directs the air through the floor
outlets, as well as the headliner outlets.
The rear system floor outlets are located
near third row seats. The flow can be
divided between vent and floor outlets
depending upon where the knob is placed
between the settings.
(Floor):
This setting directs most of the air through
the floor outlets. The rear system floor out-
lets are located near third row seats.
Passenger Compartment Air FilterOutside air is routed through a passenger
compartment air filter before entering the
vehicle. This filter removes certain parti-
cles from the air, including pollen and dust
particles. Reductions in airflow, which may
occur more quickly in dusty areas, indicate
that the filter needs to be replaced early.
The filter should be replaced as part of
routine scheduled maintenance. Refer to
“Scheduled Maintenance” in “Mainte-
nance Schedule” in the “Maintenance
Schedule” section for when to replace the
filter.
To change the passenger compartment air
filter, use the following steps:
1580378
1) Remove the push pins from the rear of
the passenger’s side air inlet panel. It is
located in the rear of the engine com-partment on the passenger side of the
vehicle.
2) Open the hood.
3) Remove the push pins from the top and
forward edge of the passenger’s side
air inlet panel.
4) Remove the air inlet panel.
5) Remove the filter from the filter housing
by pressing the release tab at the
inboard edge of the filter housing.
1394346
6) Remove the filter from the vehicle.
7) Install a new passenger compartment
air filter. For the type of filter to use refer
to “Normal Maintenance Replacement
Parts” in “Maintenance Schedule” in the
“Maintenance Schedule” section.
8) Reverse Steps 1 through 5.

5-6 SERVICE AND APPEARANCE CARE
78J00-03E
Engine Compartment OverviewWhen you open the hood, here is what you will see:
1708418
A. Engine Air Cleaner/Filter.
Refer to “Engine Air Cleaner/Filter” in this section.
B. Power Steering Fluid Reservoir (Out of View).
Refer to “Power Steering Fluid” in this section.
C. Engine Oil Fill Cap (Out of View). Refer to “When to Add
Engine Oil” under “Engine Oil” in this section.
D. Engine Oil Dipstick.
Refer to “Checking Engine Oil” under “Engine Oil” in this sec-
tion.
E. Brake Fluid Reservoir. Refer to “Brake Fluid” under “Brakes”F. Underhood Fuse Block.
Refer to “Engine Compartment Fuse Block” in this section.
G. Remote Positive (+) Terminal.
Refer to “Jump Starting” in this section.
H. Engine Coolant Recovery Tank.
Refer to “Cooling System” in this section.
I. Windshield Washer Fluid Reservoir. Refer to “Adding
Washer Fluid” under “Windshield Washer Fluid” in this sec-
tion.

5-9 SERVICE AND APPEARANCE CARE
78J00-03E
system to work properly, you must reset
the system every time the oil is changed.
When the system has calculated that oil
life has been diminished, it will indicate
that an oil change is necessary. A change
engine oil light and a CHANGE ENGINE
OIL SOON message will come on. Refer to
“Change Engine Oil Light” in “Warning
Lights, Gages, and Indicators” in the
“Instrument Panel” section and “DIC Warn-
ings and Messages” in “Driver Information
Center (DIC)” in the “Instrument Panel”
section. Change your oil as soon as possi-
ble within the next 600 miles (1000 km). It
is possible that, if you are driving under the
best conditions, the oil life system may not
indicate that an oil change is necessary for
over a year. However, your engine oil and
filter must be changed at least once a year
and at this time the system must be reset.
Your dealer has trained service people
who will perform this work and reset the
system. It is also important to check your
oil regularly and keep it at the proper level.
If the system is ever reset accidentally, you
must change your oil at 3000 miles (5000
km) since your last oil change. Remember
to reset the oil life system whenever the oil
is changed.
How to Reset the Engine Oil Life Sys-
tem
The Engine Oil Life System calculates
when to change your engine oil and filter
based on vehicle use. Anytime your oil ischanged, reset the system so it can calcu-
late when the next oil change is required. If
a situation occurs where you change your
oil prior to a change engine oil light or
CHANGE ENGINE OIL SOON message
being turned on, reset the system.
1) Turn the ignition key to RUN with the
engine off.
2) Fully press and release the accelerator
pedal three times within five seconds.
The change engine oil light will flash
while the system is resetting.
3) When the light stops flashing, turn the
key to LOCK.
If the light or message comes back on and
stays on when you start your vehicle, the
engine oil life system has not reset.
Repeat the procedure.
What to Do with Used Oil
Used engine oil contains certain elements
that may be unhealthy for your skin and
could even cause cancer. Do not let used
oil stay on your skin for very long. Clean
your skin and nails with soap and water, or
a good hand cleaner. Wash or properly
dispose of clothing or rags containing used
engine oil. See the manufacturer’s warn-
ings about the use and disposal of oil prod-
ucts.
Used oil can be a threat to the environ-
ment. If you change your own oil, be sure
to drain all the oil from the filter before dis-
posal. Never dispose of oil by putting it inthe trash, pouring it on the ground, into
sewers, or into streams or bodies of water.
Instead, recycle it by taking it to a place
that collects used oil. If you have a prob-
lem properly disposing of your used oil,
ask your dealer, a service station, or a
local recycling center for help.
Engine Air Cleaner/FilterThe engine air cleaner/filter is located in
the engine compartment on the passen-
ger’s side of the vehicle. Refer to “Engine
Compartment Overview” in this section for
more information on location.
When to Inspect the Engine Air Cleaner/
Filter
Inspect the air cleaner/filter at the Mainte-
nance II intervals and replace it at the first
oil change after each 50000 mile (83000
km) interval. Refer to “Scheduled Mainte-
nance” in “Maintenance Schedule” in the
“Maintenance Schedule” section for more
information. If you are driving in dusty/dirty
conditions, inspect the filter at each engine
oil change.
How to Inspect the Engine Air Cleaner/
Filter
To inspect the air cleaner/filter remove the
filter from the vehicle and lightly shake the
filter to release loose dust and dirt. If the fil-
ter remains caked with dirt, a new filter is
required.

5-10 SERVICE AND APPEARANCE CARE
78J00-03E
To inspect or replace the engine air
cleaner/filter, do the following:
1) Turn off the engine.
1733570
2) Disconnect the air flow sensor electrical
connector.
3) Loosen the screws on the clamps hold-
ing the air outlet duct in place. Do not
pry the clamps off.
1733580
4) Remove the air outlet duct.
5) Undo the clamps on the filter cover. To
remove the cover, pull up on the front
and then pull the cover out.
6) Inspect or replace the engine air
cleaner/filter. Wipe all dust from inside
of the housing and inspect the air
cleaner and air outlet duct for cracks,
cuts, and deterioration. The air outlet
duct must be replaced if damaged.
7) Reinstall the filter cover and latch the
clamps.
8) Reattach the air outlet duct and tighten
the screws on the clamps that hold the
duct in place.
9) Reconnect the air flow sensor electrical
connector.
Automatic Transaxle FluidIt is not necessary to check the transaxle
fluid level. A transaxle fluid leak is the only
reason for fluid loss. If a leak occurs, take
your vehicle to the dealership service
department and have it repaired as soon
as possible.
Change the fluid at the intervals listed in
“Additional Required Services” in “Mainte-
nance Schedule” in the “Maintenance
Schedule” section, and be sure to use the
transaxle fluid listed in “Recommended
WARNING
Operating the engine with the air
cleaner/filter off can cause you or
others to be burned. The air cleaner
not only cleans the air; it helps to
stop flames if the engine backfires. If
it is not there and the engine back-
fires, you could be burned. Do not
drive with it off, and be careful work-
ing on the engine with the air cleaner/
filter off.
CAUTION
If the air cleaner/filter is off, a back-
fire can cause a damaging engine
fire. And, dirt can easily get into your
engine, which will damage it. Always
have the air cleaner/filter in place
when you are driving.

6-2 MAINTENANCE SCHEDULE
78J00-03E
Some maintenance services can be com-
plex. So, unless you are technically quali-
fied and have the necessary equipment,
you should have your dealer do these jobs.
When you go to your dealer for your ser-
vice needs, you will know that trained and
supported service technicians will perform
the work using genuine parts.
“Owner Checks and Services” in this sec-
tion tells you what should be checked,
when to check it, and what you can easily
do to help keep your vehicle in good condi-
tion.
The proper replacement parts, fluids, and
lubricants to use are listed in “Recom-
mended Fluids and Lubricants” and “Nor-
mal Maintenance Replacement Parts” in
this section. When your vehicle is serviced,
make sure these are used. All parts should
be replaced and all necessary repairs
done before you or anyone else drives the
vehicle.
Scheduled MaintenanceWhen the change engine oil light and/or
CHANGE ENGINE OIL SOON message
comes on, it means that service is required
for your vehicle. Have your vehicle ser-
viced as soon as possible within the next
600 miles (1000 km). It is possible that, if
you are driving under the best conditions,
the engine oil life system may not indicate
that vehicle service is necessary for over a
year. However, the engine oil and filter
must be changed at least once a year (or
10 months if operated in Canada) and at
this time the system must be reset. Your
dealer has trained service technicians who
will perform this work using genuine parts
and reset the system.
If the engine oil life system is ever reset
accidentally, you must service your vehicle
within 3000 miles (5000 km) since your last
service. Remember to reset the oil life sys-
tem whenever the oil is changed. Refer to
“Engine Oil Life System” in “Checking
Things Under the Hood” in the “Service
and Appearance Care” section for informa-
tion on the Engine Oil Life System and
resetting the system.
For ALL except CANADA
When the change engine oil light and/or
CHANGE ENGINE OIL SOON message
appears, certain services, checks, and
inspections are required. Required ser-
vices are described in the following for
“Maintenance I” and “Maintenance II”.Generally, it is recommended that your first
service be Maintenance I, your second
service be Maintenance II, and that you
alternate Maintenance I and Maintenance
II thereafter. However, in some cases,
Maintenance II may be required more
often.
Maintenance I
Use Maintenance I if the light/message
comes on within 10 months since the vehi-
cle was purchased or Maintenance II was
performed.
Maintenance II
Use Maintenance II if the previous service
performed was Maintenance I. Always use
Maintenance II whenever the light/mes-
sage comes on 10 months or more since
the last service or if the light/message has
not come on at all for one year.
For CANADA
Use For CANADA Scheduled Maintenance
if the light/message comes on or if more
than 10 months have elapsed since the
most recent maintenance service was per-
formed.

6-3 MAINTENANCE SCHEDULE
78J00-03E
Scheduled Maintenance except CANADA
Service Instruction Maintenance I Maintenance II
Change engine oil and filter. Change engine oil and filter if the light/message has not come on
at all for one year.
 Refer to “Engine Oil” in “Checking Things Under the Hood” in the
“Service and Appearance Care” section.
••
Reset oil life system.
An Emission Control Service. If the system is ever reset accidentally, perform the maintenance
service within 3000 miles (5000 km) since your last service.
 Refer to “Engine Oil Life System” in “Checking Things Under the
Hood” in the “Service and Appearance Care” section.
Visually check for any leaks or
damage. A fluid loss in any vehicle system could indicate a problem.
 Have the system inspected and repaired and the fluid level
checked.
 Add fluid if needed.••
Rotate tires and check infla-
tion pressures and wear. Rotate tires every 5000 to 8000 miles (8000 to 13000 km).
 Refer to “Tire Inspection and Rotation” in “Tires” in the “Service
and Appearance Care” section and “At Least Once a Month” in
this section.••
Inspect brake system. Visually inspect brake lines and hoses for proper hook-up, bind-
ing, leaks, cracks, chafing, etc.
 Inspect disc brake pads for wear and rotors for surface condition.
 Inspect drum brake linings/shoes for wear or cracks (if equipped).
 Inspect other brake parts, including drums, wheel cylinders, cali-
pers, parking brake, etc.
 Check parking brake adjustment.••
Check engine coolant and
windshield washer fluid levels
and add fluid as needed.••
Perform any needed addi-
tional services. Refer to “Additional Required Services except CANADA” in this
section.••

6-4 MAINTENANCE SCHEDULE
78J00-03E
Service Instruction Maintenance I Maintenance II
Inspect engine air cleaner fil-
ter. If necessary, replace filter. Refer to “Engine Air Cleaner/Filter” in “Checking Things Under the
Hood” in the “Service and Appearance Care” section.
 If you drive regularly under dusty conditions, inspect the filter at
each engine oil change.•
Inspect suspension and steer-
ing components. Visually inspect front and rear suspension and steering system for
damaged, loose, or missing parts, signs of wear.
 Inspect power steering cables for proper hook-up, binding,
cracks, chafing, etc. (if equipped).•
Inspect engine cooling sys-
tem. Visually inspect hoses and have them replaced if they are
cracked, swollen, or deteriorated.
 Inspect all pipes, fittings and clamps; replace parts as needed.
 To help ensure proper operation, a pressure test of the cooling
system and pressure cap and cleaning the outside of the radiator
and air conditioning condenser is recommended at least once a
year.•
Inspect wiper blades. Visually inspect wiper blades for wear or cracking.
 Replace wiper blades that appear worn or damaged or that streak
or miss areas of the windshield.•
Inspect restraint system com-
ponents. Make sure the safety belt reminder light and all your belts, buck-
les, latch plates, retractors, and anchorages are working properly.
 Look for any other loose or damaged safety belt system parts.
 If you see anything that might keep a safety belt system from
doing its job, have it repaired.
 Have any torn or frayed safety belts replaced.
 Also look for any opened or broken airbag coverings, and have
them repaired or replaced.
 The airbag system does not need regular maintenance.•

6-5 MAINTENANCE SCHEDULE
78J00-03E
Service Instruction Maintenance I Maintenance II
Lubricate body components. Lubricate all key lock cylinders, hood latch assemblies, secondary
latches, pivots, spring anchor and release pawl, hood and door
hinges, rear folding seats, and liftgate hinges.
 More frequent lubrication may be required when exposed to a cor-
rosive environment such as winter road salt.
 Applying silicone grease on weatherstrips with a clean cloth will
make them last longer, seal better, and not stick or squeak.•
Inspect passenger compart-
ment air filter. Replace the air filter, if necessary.
 If you drive regularly under dusty conditions, the filter may require
replacement more often.•
Inspect throttle system. Check system for interference or binding and for damaged or
missing parts.
 Replace parts as needed.
 Replace any components that have high effort or excessive wear.•