2007 SUZUKI XL7 check oil

5-6 SERVICE AND APPEARANCE CARE
78J00-03E
Engine Compartment OverviewWhen you open the hood, here is what you will see:
1708418
A. Engine Air Cleaner/Filter.
Refer to “Engine Air Cleaner/Filter” in this section.
B. Power Steering Fluid Reservoir (Out of View).
Refer to “Power Steering Fluid” in this section.
C. Engine Oil Fill Cap (Out of View). Refer to “When to Add
Engine Oil” under “Engine Oil” in this section.
D. Engine Oil Dipstick.
Refer to “Checking Engine Oil” under “Engine Oil” in this sec-
tion.
E. Brake Fluid Reservoir. Refer to “Brake Fluid” under “Brakes”F. Underhood Fuse Block.
Refer to “Engine Compartment Fuse Block” in this section.
G. Remote Positive (+) Terminal.
Refer to “Jump Starting” in this section.
H. Engine Coolant Recovery Tank.
Refer to “Cooling System” in this section.
I. Windshield Washer Fluid Reservoir. Refer to “Adding
Washer Fluid” under “Windshield Washer Fluid” in this sec-
tion.

5-7 SERVICE AND APPEARANCE CARE
78J00-03E
Engine OilChecking Engine Oil
It is a good idea to check your engine oil
every time you get fuel. In order to get an
accurate reading, the oil must be warm
and the vehicle must be on level ground.
The engine oil dipstick handle is a yellow
loop. Refer to “Engine Compartment Over-
view” in this section for the location of the
engine oil dipstick.
1) Turn off the engine and give the oil sev-
eral minutes to drain back into the oil
pan. If you do not do this, the oil dip-
stick might not show the actual level.
2) Pull out the dipstick and clean it with a
paper towel or cloth, then push it back
in all the way. Remove it again, keeping
the tip down, and check the level.When to Add Engine Oil
830434
If the oil is below the cross-hatched area at
the tip of the dipstick, you need to add at
least one quart/liter of oil. But you must
use the right kind. This section explains
what kind of oil to use. For engine oil
crankcase capacity, refer to “Capacities
and Specifications” in this section.
824596
SAE 5W-30 may not appear on all caps.
Refer to “Engine Compartment Overview”
in this section for the location of the engine
oil fill cap.
Be sure to add enough oil to put the level
somewhere in the proper operating range
in the cross-hatched area. Push the dip-
stick all the way back in when you are
through.
CAUTION
Do not add too much oil. If the engine
has so much oil that the oil level gets
above the cross-hatched area that
shows the proper operating range,
the engine could be damaged.

5-9 SERVICE AND APPEARANCE CARE
78J00-03E
system to work properly, you must reset
the system every time the oil is changed.
When the system has calculated that oil
life has been diminished, it will indicate
that an oil change is necessary. A change
engine oil light and a CHANGE ENGINE
OIL SOON message will come on. Refer to
“Change Engine Oil Light” in “Warning
Lights, Gages, and Indicators” in the
“Instrument Panel” section and “DIC Warn-
ings and Messages” in “Driver Information
Center (DIC)” in the “Instrument Panel”
section. Change your oil as soon as possi-
ble within the next 600 miles (1000 km). It
is possible that, if you are driving under the
best conditions, the oil life system may not
indicate that an oil change is necessary for
over a year. However, your engine oil and
filter must be changed at least once a year
and at this time the system must be reset.
Your dealer has trained service people
who will perform this work and reset the
system. It is also important to check your
oil regularly and keep it at the proper level.
If the system is ever reset accidentally, you
must change your oil at 3000 miles (5000
km) since your last oil change. Remember
to reset the oil life system whenever the oil
is changed.
How to Reset the Engine Oil Life Sys-
tem
The Engine Oil Life System calculates
when to change your engine oil and filter
based on vehicle use. Anytime your oil ischanged, reset the system so it can calcu-
late when the next oil change is required. If
a situation occurs where you change your
oil prior to a change engine oil light or
CHANGE ENGINE OIL SOON message
being turned on, reset the system.
1) Turn the ignition key to RUN with the
engine off.
2) Fully press and release the accelerator
pedal three times within five seconds.
The change engine oil light will flash
while the system is resetting.
3) When the light stops flashing, turn the
key to LOCK.
If the light or message comes back on and
stays on when you start your vehicle, the
engine oil life system has not reset.
Repeat the procedure.
What to Do with Used Oil
Used engine oil contains certain elements
that may be unhealthy for your skin and
could even cause cancer. Do not let used
oil stay on your skin for very long. Clean
your skin and nails with soap and water, or
a good hand cleaner. Wash or properly
dispose of clothing or rags containing used
engine oil. See the manufacturer’s warn-
ings about the use and disposal of oil prod-
ucts.
Used oil can be a threat to the environ-
ment. If you change your own oil, be sure
to drain all the oil from the filter before dis-
posal. Never dispose of oil by putting it inthe trash, pouring it on the ground, into
sewers, or into streams or bodies of water.
Instead, recycle it by taking it to a place
that collects used oil. If you have a prob-
lem properly disposing of your used oil,
ask your dealer, a service station, or a
local recycling center for help.
Engine Air Cleaner/FilterThe engine air cleaner/filter is located in
the engine compartment on the passen-
ger’s side of the vehicle. Refer to “Engine
Compartment Overview” in this section for
more information on location.
When to Inspect the Engine Air Cleaner/
Filter
Inspect the air cleaner/filter at the Mainte-
nance II intervals and replace it at the first
oil change after each 50000 mile (83000
km) interval. Refer to “Scheduled Mainte-
nance” in “Maintenance Schedule” in the
“Maintenance Schedule” section for more
information. If you are driving in dusty/dirty
conditions, inspect the filter at each engine
oil change.
How to Inspect the Engine Air Cleaner/
Filter
To inspect the air cleaner/filter remove the
filter from the vehicle and lightly shake the
filter to release loose dust and dirt. If the fil-
ter remains caked with dirt, a new filter is
required.

5-14 SERVICE AND APPEARANCE CARE
78J00-03E
C. Pressure Cap
If the coolant inside the coolant recovery
tank is boiling, do not do anything else until
it cools down. The vehicle should be
parked on a level surface.
When the engine is cold, the coolant level
should be at or above the cold fill line on
the coolant recovery tank. If it is not, there
may be a leak at the pressure cap or in the
radiator hoses, heater hoses, radiator,
water pump, or somewhere else in the
cooling system.If there seems to be no leak, with the
engine on, check to see if the electric
engine cooling fans are running. If the
engine is overheating, the fans should be
running. If the fans are not running, the
vehicle needs service.How to Add Coolant to the Coolant
Recovery Tank
If you have not found a problem yet, but
the coolant level is not at the cold fill line,
add a 50/50 mixture of clean, drinkable
water and DEX-COOL
® engine coolant at
the coolant recovery tank. Refer to “Engine
Coolant” in this section for more informa-
tion.
WARNING
An electric engine cooling fan under
the hood can start up even when the
engine is not running and can injure
you. Keep hands, clothing, and tools
away from any underhood electric
fan.
WARNING
Heater and radiator hoses, and other
engine parts, can be very hot. Do not
touch them. If you do, you can be
burned.
Do not run the engine if there is a
leak. If you run the engine, it could
lose all coolant. That could cause an
engine fire, and you could be burned.
Get any leak fixed before you drive
the vehicle.
CAUTION
Engine damage from running your
engine without coolant is not covered
by your warranty. Refer to “Over-
heated Engine Protection Operating
Mode” in this section for information
on driving to a safe place in an emer-
gency.
CAUTION
Using coolant other than DEX-COOL
®
may cause premature engine, heater
core, or radiator corrosion. In addi-
tion, the engine coolant could require
changing sooner, at 30000 miles
(50000 km) or 24 months, whichever
occurs first. Any repairs would not be
covered by your warranty. Always
use DEX-COOL
® (silicate-free) cool-
ant in your vehicle.
WARNING
Adding only plain water to your cool-
ing system can be dangerous. Plain
water, or some other liquid such as
alcohol, can boil before the proper
coolant mixture will. Your vehicle’s
coolant warning system is set for the
proper coolant mixture. With plain
water or the wrong mixture, your
engine could get too hot but you
would not get the overheat warning.
Your engine could catch fire and you
or others could be burned. Use a 50/
50 mixture of clean, drinkable water
and DEX-COOL
® coolant.
CAUTION
In cold weather, water can freeze and
crack the engine, radiator, heater
core and other parts. Use the recom-
mended coolant and the proper cool-
ant mixture.

5-50 SERVICE AND APPEARANCE CARE
78J00-03E
The best way to preserve the vehicle’s fin-
ish is to keep it clean by washing it often
with lukewarm or cold water.
Do not wash the vehicle in the direct rays
of the sun. Use a car washing soap. Do not
use strong soaps or chemical detergents.
Be sure to rinse the vehicle well, removing
all soap residue completely. Approved
cleaning products can be obtained from
your dealer. Refer to “Vehicle Care/
Appearance Materials” in this section. Do
not use cleaning agents that are petroleum
based, or that contain acid or abrasives.
All cleaning agents should be flushed
promptly and not allowed to dry on the sur-
face, or they could stain. Dry the finish with
a soft, clean chamois or an all-cotton towel
to avoid surface scratches and water spot-
ting.
High pressure car washes may cause
water to enter the vehicle.Cleaning Exterior Lamps/LensesUse only lukewarm or cold water, a soft
cloth and a car washing soap to clean
exterior lamps and lenses. Follow instruc-
tions under “Washing Your Vehicle” in this
section.Finish CareOccasional waxing or mild polishing of the
vehicle by hand may be necessary to
remove residue from the paint finish.
Approved cleaning products can be
obtained from your dealer. Refer to “Vehi-cle Care/Appearance Materials” in this
section.
The vehicle has a basecoat/clearcoat paint
finish. The clearcoat gives more depth and
gloss to the colored basecoat. Always use
waxes and polishes that are non-abrasive
and made for a basecoat/clearcoat paint
finish.
Foreign materials such as calcium chloride
and other salts, ice melting agents, road oil
and tar, tree sap, bird droppings, chemi-
cals from industrial chimneys, etc., can
damage the vehicle’s finish if they remain
on painted surfaces. Wash the vehicle as
soon as possible. If necessary, use non-
abrasive cleaners that are marked safe for
painted surfaces to remove foreign matter.
Exterior painted surfaces are subject to
aging, weather, and chemical fallout that
can take their toll over a period of years.
To help keep the paint finish looking new,
keep the vehicle in a garage or covered
whenever possible.
Windshield and Wiper BladesIf the windshield is not clear after using the
windshield washer, or if the wiper blade
chatters when running, wax, sap, or other
material may be on the blade or wind-
shield.
Clean the outside of the windshield with a
glass cleaning liquid or powder and water
solution. The windshield is clean if beads
do not form when it is rinsed with water.
Grime from the windshield will stick to the
wiper blades and affect their performance.
Clean the blade by wiping vigorously with
a cloth soaked in full-strength windshield
washer solvent. Then rinse the blade with
water.
Check the wiper blades and clean them as
necessary; replace blades that look worn.Aluminum WheelsKeep the wheels clean using a soft clean
cloth with mild soap and water. Rinse with
CAUTION
Machine compounding or aggres-
sive polishing on a basecoat/
clearcoat paint finish may damage it.
Use only non-abrasive waxes and
polishes that are made for a
basecoat/clearcoat paint finish on
your vehicle.
CAUTION
If you use strong soaps, chemicals,
abrasive polishes, cleaners, brushes,
or cleaners that contain acid on alu-
minum or chrome-plated wheels, you
could damage the surface of the
wheel(s). The repairs would not be
covered by your warranty. Use only
SUZUKI-approved cleaners on alumi-
num or chrome-plated wheels.

6-1 MAINTENANCE SCHEDULE
78J00-03E
Maintenance ScheduleIntroductionImportant: Keep engine oil at the proper
level and change as recommended.Maintenance RequirementsYour Vehicle and the Environment
Proper vehicle maintenance not only helps
to keep your vehicle in good working condi-
tion, but also helps the environment. All
recommended maintenance is important.
Improper vehicle maintenance can even
affect the quality of the air we breathe.
Improper fluid levels or the wrong tire infla-
tion can increase the level of emissions
from your vehicle. To help protect our envi-
ronment, and to keep your vehicle in good
condition, be sure to maintain your vehicle
properly.Using the Maintenance ScheduleWe want to help you keep your vehicle in
good working condition. But we do not
know exactly how you will drive it. You may
drive very short distances only a few times
a week. Or you may drive long distances
all the time in very hot, dusty weather. You
may use your vehicle in making deliveries.
Or you may drive it to work, to do errands,
or in many other ways.
Because of all the different ways people
use their vehicles, maintenance needs
vary. You may need more frequent checks
and replacements. So please read the fol-
lowing and note how you drive. If you have
any questions on how to keep your vehicle
in good condition, see your dealer.This schedule is for vehicles that:
 carry passengers and cargo within rec-
ommended limits. You will find these lim-
its on the Tire and Loading Information
label. Refer to “Loading Your Vehicle” in
“Your Driving, the Road, and Your Vehi-
cle” in the “Driving Your Vehicle” section.
 are driven on reasonable road surfaces
within legal driving limits.
 use the recommended fuel. Refer to
“Gasoline Octane” in “Fuel” in the “Ser-
vice and Appearance Care” section.
The services in “Scheduled Maintenance”
in this section should be performed when
indicated. Refer to “Additional Required
Services” in this section for further informa-
tion.
CAUTION
Maintenance intervals, checks,
inspections, replacement parts, and
recommended fluids and lubricants
as prescribed in this manual are nec-
essary to keep your vehicle in good
working condition. Any damage
caused by failure to follow scheduled
maintenance might not be covered by
warranty.
WARNING
Performing maintenance work on a
vehicle can be dangerous. In trying to
do some jobs, you can be seriously
injured. Do your own maintenance
work only if you have the required
know-how and the proper tools and
equipment for the job. If you have any
doubt, see your dealer to have a qual-
ified technician do the work. Refer to
“Doing Your Own Service Work” in
the “SERVICE AND APPEARANCE
CARE” section.

6-2 MAINTENANCE SCHEDULE
78J00-03E
Some maintenance services can be com-
plex. So, unless you are technically quali-
fied and have the necessary equipment,
you should have your dealer do these jobs.
When you go to your dealer for your ser-
vice needs, you will know that trained and
supported service technicians will perform
the work using genuine parts.
“Owner Checks and Services” in this sec-
tion tells you what should be checked,
when to check it, and what you can easily
do to help keep your vehicle in good condi-
tion.
The proper replacement parts, fluids, and
lubricants to use are listed in “Recom-
mended Fluids and Lubricants” and “Nor-
mal Maintenance Replacement Parts” in
this section. When your vehicle is serviced,
make sure these are used. All parts should
be replaced and all necessary repairs
done before you or anyone else drives the
vehicle.
Scheduled MaintenanceWhen the change engine oil light and/or
CHANGE ENGINE OIL SOON message
comes on, it means that service is required
for your vehicle. Have your vehicle ser-
viced as soon as possible within the next
600 miles (1000 km). It is possible that, if
you are driving under the best conditions,
the engine oil life system may not indicate
that vehicle service is necessary for over a
year. However, the engine oil and filter
must be changed at least once a year (or
10 months if operated in Canada) and at
this time the system must be reset. Your
dealer has trained service technicians who
will perform this work using genuine parts
and reset the system.
If the engine oil life system is ever reset
accidentally, you must service your vehicle
within 3000 miles (5000 km) since your last
service. Remember to reset the oil life sys-
tem whenever the oil is changed. Refer to
“Engine Oil Life System” in “Checking
Things Under the Hood” in the “Service
and Appearance Care” section for informa-
tion on the Engine Oil Life System and
resetting the system.
For ALL except CANADA
When the change engine oil light and/or
CHANGE ENGINE OIL SOON message
appears, certain services, checks, and
inspections are required. Required ser-
vices are described in the following for
“Maintenance I” and “Maintenance II”.Generally, it is recommended that your first
service be Maintenance I, your second
service be Maintenance II, and that you
alternate Maintenance I and Maintenance
II thereafter. However, in some cases,
Maintenance II may be required more
often.
Maintenance I
Use Maintenance I if the light/message
comes on within 10 months since the vehi-
cle was purchased or Maintenance II was
performed.
Maintenance II
Use Maintenance II if the previous service
performed was Maintenance I. Always use
Maintenance II whenever the light/mes-
sage comes on 10 months or more since
the last service or if the light/message has
not come on at all for one year.
For CANADA
Use For CANADA Scheduled Maintenance
if the light/message comes on or if more
than 10 months have elapsed since the
most recent maintenance service was per-
formed.

6-3 MAINTENANCE SCHEDULE
78J00-03E
Scheduled Maintenance except CANADA
Service Instruction Maintenance I Maintenance II
Change engine oil and filter. Change engine oil and filter if the light/message has not come on
at all for one year.
 Refer to “Engine Oil” in “Checking Things Under the Hood” in the
“Service and Appearance Care” section.
••
Reset oil life system.
An Emission Control Service. If the system is ever reset accidentally, perform the maintenance
service within 3000 miles (5000 km) since your last service.
 Refer to “Engine Oil Life System” in “Checking Things Under the
Hood” in the “Service and Appearance Care” section.
Visually check for any leaks or
damage. A fluid loss in any vehicle system could indicate a problem.
 Have the system inspected and repaired and the fluid level
checked.
 Add fluid if needed.••
Rotate tires and check infla-
tion pressures and wear. Rotate tires every 5000 to 8000 miles (8000 to 13000 km).
 Refer to “Tire Inspection and Rotation” in “Tires” in the “Service
and Appearance Care” section and “At Least Once a Month” in
this section.••
Inspect brake system. Visually inspect brake lines and hoses for proper hook-up, bind-
ing, leaks, cracks, chafing, etc.
 Inspect disc brake pads for wear and rotors for surface condition.
 Inspect drum brake linings/shoes for wear or cracks (if equipped).
 Inspect other brake parts, including drums, wheel cylinders, cali-
pers, parking brake, etc.
 Check parking brake adjustment.••
Check engine coolant and
windshield washer fluid levels
and add fluid as needed.••
Perform any needed addi-
tional services. Refer to “Additional Required Services except CANADA” in this
section.••