2007 SKODA OCTAVIA TOUR warning

163
DO-IT-YOURSELF
Changing a wheelWarning

In the case of a flat tyre or punc-
ture, park the vehicle off the road,
switch on the hazard warning lights
and place the warning triangle in po-
sition - note any statutory require-
ments.

All the vehicle occupants should
leave the car and move to a safe area
(e.g. behind safety barrier).


Apply handbrake firmly and engage
a gear. Chock the opposite wheel with
a stone or similar if the car is stand-
ing on a slope.

Never start the engine when the
car is jacked up - risk of accident!

If towing a trailer, unhitch the
trailer from the car before changing
the wheel.

Carry out wheel change on a flat, level
surface, as far as possible.

Remove the car tool kit and spare wheel
from the luggage compartment.

Attach the wire hook (from the car tool
kit) at the edge of the full wheel trim* oppo-
site the air valve. Push the wheel wrench
through the wire hook and pull off the wheel
trim - see illustration.

If light-alloy wheels are fitted, use the
plastic clip supplied to pull off the covers
for the wheel bolts.

Unscrew the safety wheel bolts* - see
page 166.

Fit wheel wrench onto the wheel bolt as
far as the stop and turn to the left. Hold the
wrench as close as possible to its end for
this operation. If the bolts cannot be slack-
ened, you can carefully apply pressure to
the end of the wheel wrench with your foot.
Ensure that you are standing properly and
hold tight on the car. Slacken the wheel
bolts about one turn.

164DO-IT-YOURSELF
Fit the car jack onto the car. Recesses
are provided on the lower sill (at the front
and rear). Below this is the point at which
the car jack should be positioned - see ar-
rows in the illustration.

Position the car jack so that its claw fits
around the web of the lower sill A and the
moving base plate of the car jack B is posi-
tioned flat on the ground.
Warning

Always raise the vehicle with the
doors closed - risk of injury.

Take suitable measures to prevent
the base of the lifting jack from slip-
ping off - risk of injury!

Place the lifting jack only on a
solid and even surface.

Not positioning the lifting jack at
the specified points can result in
damage to the vehicle. In addition,
the jack may slip off if it does not
have sufficient grip - risk of injury!

Never start the engine if the vehi-
cle is lifted - risk of accident.

Never lie under the vehicle if the
vehicle is only lifted with the vehicle
lifting jack.

It is important to support the ve-
hicle with suitable supporting blocks
if you wish to work under the lifted
vehicle - risk of injury! -
If the surface is soft, place a large
solid base below the foot of the jack.
- Rotate the crank to raise the claws of the jack sufficiently so that the jack can just
still be fitted below the car.
- The claw of the jack must be fitted around the vertical web of the lower sill
so that the jack cannot slip off when the
car is raised.
- The base of the jack should be resting fully on a firm surface.
- Align jack and at the same time raise the claw of the jack further until the claw is
touching the web.

165
DO-IT-YOURSELF

Jack up car until the wheel is just clear
of the ground.

Remove wheel bolts (after slackening)
1),
place them down on a clean surface (cloth,
paper, wheel cap) next to the car jack and
take off wheel.

Fit on spare wheel and attach wheel
bolts
1).

Tighten all the wheel bolts slightly. The
wheel bolts should be clean and turn freely.

On no account grease or oil them!

Lower car and tighten the wheel bolts
diagonally.

Press on the full wheel trim* first at the
valve opening and then apply pressure
around the entire circumference so that the
trim locks in position.
1)In order to accelerate the screwing out and in,
use the handle part of the screwdriver from the
car tool kit, which has on its end a hexagon
socket for the screw head.

Place the wheel removed in the spare
wheel well and secure with the handwheel.
Notes

After changing a wheel, pay attention to
the following points:
- Check the inflation pressure of the spare wheel fitted.
- Have the tightening torque of the wheel bolts checked with a torque wrench as
soon as possible. The tightening torque
for steel and light alloy wheels is 120 Nm.

Have the faulty wheel repaired as quickly
as possible. Warning
In case of incorrect treatment of the
wheel bolts, the wheel can loosen
when the car is moving - risk of acci-
dent!
Wheel bolts must be clean and must
turn easily. However
, they must never
be treated with grease or oil.
If the wheel bolts are tightened to a
too low tightening torque, the trims
can loosen when the car is moving -
risk of accident! A tightening torque,
which is too high, can damage the
bolts and threads and this can result
in permanent deformation of the con-
tact surfaces on the trims.
If it is intended to subsequently fit
wheels or tyres other than the factory-
fitted versions to the car, it is essen-
tial to read the remarks on page 156.

167
DO-IT-YOURSELF
FusesThe individual electrical circuits are pro-
tected by fuses.
The fuses are located on the left-hand face
end of the instrument cluster below the co-
ver.
Space is provided on the right for spare fu-
ses - see page 168.
Additional fuses are located in the engine
compartment on the battery. We recom-
mend having these fuses replaced by a
Škoda Dealer.Replacing a fuse
Switch off the ignition and the relevant
electrical component.

To remove the cover, place a screwdriver
against the cover (arrow on cover) and ca-
refully lever it off.

Refer to the list of fuses as shown in il-
lustration to find which fuse belongs to the
faulty component - see illustration on page
168.

Remove the blown fuse.

A blown fuse is recognizable from the
melted metal strip - replace with a new fuse
of the same rating.
Notes

If a newly inserted fuse blows again af-
ter a short time, the electrical system should
then be inspected as soon as possible by
a Škoda Dealer.

On no account „repair“ fuses as this may
cause major damage to another point of the
electrical system.

Certain of the electrical components
listed are fitted only to particular model
versions or are optional equipment.

We recommend always carrying with
you a box with replacement fuses, which is
available from Škoda Dealers
1).
1)In certain countries the box with replacement
fuses is part of the basic equipment.
Warning
If the fire extinguisher is not correctly
attached, in case of sudden manoeu-
vres or an accident, it can be thrown
through the interior compartment
and cause injuries.

168DO-IT-YOURSELFFuse assignment
No. Electrical component A
1 - Mirror and spray nozzle heater,relay for cigarette lighter
el. seats ........................................ 10
2 - Turn signal lights .......................... 10
3 - Stowage compartment light ............ 5
4 - Licence plate lights ......................... 5
5 - Seat heaters, Climatronic, Navi- gation system, recirculated air
flap, multifunction steering
wheel, exterior mirror heaters ..... 7.5
6 - Central locking control unit ............. 5
7 - Reversing lights, parking aid ........ 10
8 - Mobile phone .................................. 5
9 - ABS/ESP ......................................... 5
10 - Petrol engine: control unit ............ 20
Diesel engine: control unit .............. 5No. Electrical component A
11 - Dash panel insert, selector lever
lock solenoid (automatic
gearbox) .......................................... 5
12 - Power supply for diagnosis, mobile phone ............................... 7.5
13 - Brake lights ................................... 10
14 - Interior light, central locking ......... 10
Interior light (without central
locking) ......................................... 10
15 - Instrument cluster, automatic gearbox, steering lock angle
sensor, rear-view mirrors ................ 5
16 - Air conditioning, electric water pump ............................................. 10
17 - Police .............................................. 5
18 - Right main beam .......................... 10
19 - Left main beam ............................. 10
20 - Right low beam, headlight range control ................................. 15
21 - Left low beam ............................... 15
22 - Right parking light ........................... 5
23 - Left parking light ............................. 5
24 - Wiper system, washer pump ........ 20
25 - Heater fan ..................................... 25
26 - Rear window heater ...................... 25
27 - Rear window wiper ....................... 15
28 - Fuel pump ..................................... 15
29 - Petrol engine - engine electronics, ignition ....................... 15
Diesel engine - engine
electronics .................................... 10 No. Electrical component A
30 - Power sliding/tilting roof
............... 20
31 - Automatic gearbox ........................ 20
Haldex coupling .............................. 5
32 - Petrol engine - injectors ............... 10
Diesel engine - injection pump,
control unit .................................... 30
33 - Headlight cleaning system ........... 20
34 - Petrol engine - engine electronics .................................... 10
Diesel engine - engine
electronics .................................... 10
35 - Trailer socket, socket in luggage compartment ............... 30
36 - Fog lights ...................................... 15
37 - S contact
1)................................... 10
38 - Luggage compartment light, central locking, remote fuel
filler flap release ........................... 15
39 - Hazard warning signals ................ 15
40 - Horn .............................................. 20
41 - Cigarette lighter ............................ 15
42 - Radio ............................................. 15
43 - Petrol engine: engine electronics .................................... 10
Diesel engine: engine
electronics .................................... 10
44 - Seat heaters ................................. 15
1)For electrical components which can be oper-
ated after switching off the ignition provided the
ignition key is not withdrawn, e.g. radio.

169
DO-IT-YOURSELF
Colour coding of fuses:A
light brown: ............................................. 5
dark brown: .......................................... 7.5
red: ........................................................ 10
blue: ...................................................... 15
yellow: ................................................... 20
white: ..................................................... 25
green: .................................................... 30
Notes
The fuse assignment differs depending on
the version of your car.
The pliers for removing fuses and replace-
ment fuses are not contained in the car
equipment.
Replacing a bulbThe relevant light should always be swit-
ched off first of all before replacing a bulb.
Do not grasp the glass of the bulb with your
bare fingers (even the minutest spot of dirt
reduces the operational life of the bulb).
Use a clean cloth, napkin or similar.
A bulb should only be replaced by a lamp
of the same design . The designation is
given on the base of the bulb or on the
glass.
Warning
H4 bulbs are pressurized and may
burst when they are replaced. For
this reason, always wear gloves and
eye protection when changing a H4
bulb. Models with Xenon headlamps*
If your car is fitted with xenon head-
lights, have the bulb (low beam, side
light and main beam) replaced by a
Škoda dealer.
We recommend always carrying with you in
the car a box with a set of spare bulbs, which
you received together with your car, or which
is available from your Škoda Dealer
1).
1)The small box of replacement light bulbs are part
of the basic equipping of the vehicle in some
countries

170DO-IT-YOURSELFTable of bulbs
Front Halogen Xenonheadlight headlight headlight
Low beam H4D2SMain beam
H1Side lightsW 5 W
Turn signal
lights PY21W
Fog lights H3 Rear light Octavia Octavia
unit
Estate
Rear lightsP21W
Turn signal
lights PY21W
Brake lights
P21W
P21/5W
Side lights
P21/4W
Fog lights P21WOthers Octavia
Octavia
Estate
Side turn
signal lights WY5W
License plate
light W5W
Additional
brake light W2,3W LEDInterior light
C10WReading light W 5 WBoot light C5W C10W
Door warning
light C5W
Glove box light
C3W
Interior mirror light W2,3W

178DO-IT-YOURSELFA - Discharged battery
B - Battery supplying current
Warning
Do not connect the cable to the nega-
tive terminal (-) of the discharged
battery. This can produce sparks
when the engine is started which
might ignite the gas flowing out of
the battery.
Do not affix the cable end 4 to parts
of the fuel and brake system. Warning


The non-insulated parts of the ca-
ble clamps must not touch one an-
other on any account. In addition, the
jump-start cable attached to the posi-
tive terminal of the battery must not
come into contact with electrically
conducting parts of the vehicle - risk
of short circuit!

Route the jump-start cables so
that they cannot come into contact
with rotating parts in the engine com-
partment.

Do not bend over the batteries -
risk of acid burns!

Keep sources of ignition (naked
flames, burning cigarettes etc.) well
away from the battery - risk of explo-
sion!

Start the engine as described in the sec-
tion „Starting engine“.

If the engine does not start right away,
do not crank the starter for more than 10
seconds and then wait about 30 seconds
before making a further attempt.

Once the engine is running, disconnect
both cables in exactly the reverse order.
Tow-starting/towingThe towing eyes are located at the rear right
below the bumper and at the front - see
arrow.
A tow rope or tow bar should be attached
only to these towing eyes.

Remove a ventilation grille before using
the front towing eye. Ventilation grille is held
in place with plastic spring catches in the
area of the arrow. Ventilation grille can be
removed by hand.

Grasp the top part of the grille, press
grille off in direction of arrow 1 and take out
in direction of arrow 2.

After using the towing eye, insert the
ventilation grille into the guides and press
on.