2007 SKODA OCTAVIA tow

Seats and Stowage
94
Closing stowage compartment
– Open the lid up to the stop, then you can fold it downwards.
Setting height
– First of all fold the lid to the bottom and lift it in the direction of arrow
into one of the 4 fixed positions.
Adjusting in forward/back direction
– Push the lid into the desired position.
Opening air inlet
– Pull the lock in upward direction ⇒fig. 108 .
Closing air inlet
– Push the lock as far as the stop downwards.
On vehicles fitted with air conditioning, the storage compartment is equipped with
a lockable inlet for thermally treated (warmed-up) air.
At open air supply, air flows into the storage with a temperature which is as high as
the one out of the air outlet nozzles, depending on temperature setting.
The air inlet in the storage compar tment is connected to position
 through
adjustment of the control dial for air distribution. This po sition causes the
maximum amount of air to flow into the storage compartment (depending on the
rotary regulator position for the fan).
You can use the storage compartment, for example, to temper drinks cans, etc.
If you do not use the air inlet in the storage compartment, the end cover
should always be kept closed.
Note
Push the lid of the armrest up to stop to the rear before operating the handbrake.
Stowage compartment in rear centre console*
The storage compartment is equipped with a removeable insert.
– Open the storage compartment by pulling on the upper edge of the storage compartment in the direction of arrow ⇒fig. 109 .
WARNING
The storage compartment is not a substitute for the ashtray and must also
not be used for such purposes - risk of fire!
AA
AA
Fig. 109 Centre console
at rear: Storage compart-
ment
AA
NKO A5 20 MR08.book Page 94 Wednesday, April 11, 2007 2:54 PM

Seats and Stowage95
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Seat backrest with opening for skis*
After folding open the armrest and the lid, an opening in the seat backrest
becomes visible through which you can push long objects e.g. skis etc.
You can fold open the armrest and the lid from the passenger or luggage
compartment.
Opening from passenger compartment
– Fold down the armrest of the rear seat at the loop ⇒page 74, fig. 69 .
– Pull the handle up to the stop in upward direction and fold open the lid downwards ⇒fig. 110 . Opening from luggage compartment
– Push the unlock button downwards
⇒page 95, fig. 111 and fold
the lid (with armrest) to the front.
Closing
– Fold the lid and the armrest up to the stop in upward direction - the lid must click into place audibly.
Ensure that the armrest is always locked into place after closing. You can recognize
this on the fact that the red field abov e the unlocking button of the luggage
compartment is not visible.
Fig. 110 Rear seats:
Handle of lid
Fig. 111 Luggage
compartment: Unlock
button
AA
AA
NKO A5 20 MR08.book Page 95 Wednesday, April 11, 2007 2:54 PM

Seats and Stowage
96
Storage box*
The storage box is foreseen for storage of small objects of up to 5 kg in
weight and can also be used as an armrest. You can place 2 cups or
beverage cans into the recess on the storage box.
Installing storage box
– Fold the seat backrest forwards completely.
– In the space between the folded forward seat backrest and seat
cushion of the middle seat, move the fixing holder and fold it in the
horizontal position ⇒fig. 112 . – Move the seat backrest into the vertical position.
– Move the fixing arms of the storag
e box into the locking eyes of the
fixing holder until they lock in place ⇒fig. 113 .
– Check the interlock of both fixing arms by pulling on the storage
box.
Removing storage box
– Simultaneously press on each side of the storage box the red button in direction opposite the seat back rest. The storage box releases.
– Fold the seat backrest forwards and remove the fixing holder, then move the seat backrest into the original position.
WARNING
•Do not place any hot beverages into th e cup holder. If the vehicle moves,
the hot beverages may spill - risk of scalding!
•Do not use any cups or beakers which are made of brittle material (e.g.
glass, porcelain). You might be injured by them in the event of an accident.
•While driving, the storage box can only be used as an armrest in its closed
position.
Caution
Do not open the beverages in the cup holder while driving. There is a risk of spilling
e.g. when braking and therefore the electrical components or the seat upholstery
can be damaged.
Fig. 112 Holder for
attachment
Fig. 113 Storage box
NKO A5 20 MR08.book Page 96 Wednesday, April 11, 2007 2:54 PM

Seats and Stowage97
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Through-loading bag*
Loading
– Open the boot lid/luggage compartment door.
– Push the unlock button downwards ⇒fig. 114 and fold the lid
(with armrest) to the front.
– Place the empty through-loading bag in such a way that the end of the bag with the zip lies in the boot.
– Push the objects into the thro ugh-loading bag from the boot ⇒. Securing
– Insert the securing belt of the through-loading bag into the middle
seat belt buckle ⇒fig. 115 .
– Place the securing belt on ski sport articles in the middle between the bindings ⇒.
– Pull the securing belt tight at the free end of the belt .
Stowing
– Fold the lid and the armrest up to the stop in upward direction - the lid must click into place audibly. You can recognize this on the fact that
the red field above the unlocking button of the luggage compart-
ment is not visible ⇒fig. 114 .
– Carefully fold the empty (dry) through-loading bag together, place it in the luggage compartment and secure it to prevent it slipping.
WARNING
•After placing items into the through- loading bag, you must secure the
bag with the securing belt .
•The securing belt must hold the items tight.
•Ensure that the securing belt on ski sport articles lies in the middle
between the bindings (see imprin t on the through-loading bag).
Note
•Place the skis with the tips facing the fr ont, snowboards and ski sticks with the
tips facing the rear into the through-loading bag.
•If there are several pairs of skis in the through-loading bag, ensure that the bind-
ings are positioned at the same height.
•The through-loading bag must never be folded together or stowed when
moist.
Fig. 114 Luggage
compartment: Unlock
button
Fig. 115 Attaching
through-loading bag to
middle seat belt buckle
of rear seats
AA
AA
AC
AB
AA
AA
NKO A5 20 MR08.book Page 97 Wednesday, April 11, 2007 2:54 PM

Seats and Stowage
98
Side compartment*
– You can open the compartment by turning the locks in the direction of
arrow.
The CD changer* is housed in this compartment.
Stowage compartment behind the rear seats (estate car)
Removing
– First remove the luggage compartment cover ⇒page 81. – Grasp the compartment with both hands and remove it by pulling in
direction of arrow ⇒fig. 117 .
Installing
– Push the compartment up to the stop into the catch.
– Re-insert the luggage compartment cover.
WARNING
Only place small and light objects up to a total weight of 3 kg into the
stowage compartment. In the event of a vehicle collision heavy objects
could be thrown out of the compartment - risk of injuries! For this reason,
the front part of the luggage compartmen t cover must always cover over the
stowage compartment.
Clothes hooks*
Clothes hooks are located above the rear doors ⇒fig. 118 .
Fig. 116 Luggage
compartment: Side
compartment
Fig. 117 Removing the
stowage compartment
Fig. 118 Rear door:
Clothes hooks
NKO A5 20 MR08.book Page 98 Wednesday, April 11, 2007 2:54 PM

Seats and Stowage99
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
WARNING
•Ensure that any clothes hanging from the hooks do not impair your
vision to the rear.
•Use the hooks for hanging only light items of clothing and ensure that
there are no heavy or sharp- edged objects in the pockets.
•Do not use clothes hangers for hanging up items of clothing otherwise
this will interfere with the protection offered by the head airbag*.
NKO A5 20 MR08.book Page 99 Wednesday, April 11, 2007 2:54 PM

Heating and air conditioning system101
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
WARNING
You should not leave recirculated air mode on over a longer period of time,
as “stale” air may result in fatigue in the driver and occupants, divert your
attention and also cause the windows to mist up. The risk of having an acci-
dent increases. Switch recirculated air mode off as soon as the windows
begin misting up.
Note
•The whole heat output will be needed to unfrost the windscreen and side
windows. No warm air will be fed to the f ootwell. This can lead to restriction of the
heating comfort.
•The used air streams out through the air removal openings in the luggage
compartment.
Set heating
Recommended settings of heating controls for:
Defrosting the windscreen and side windows
•Tu r n c o n t ro l d i a l ⇒page 100, fig. 119 to the right up to the stop
•Blower switch in position 3
•Turn the air distribution control into the position 
•Open air outlet vents 3 ⇒ page 102, fig. 120 and point towards the side
window.
•Close the air outlet vents 4
Keeping windscreen and side windows demisted
We recommend that you use the following setting in cases where the windows are
misted up more than usual (e.g. when it is raining):
•Control dial where necessary to the heating range
•Blower switch in position 2 or 3
•Control dial to  or  as required or to any desired position between
these symbols
•Open air outlet vents 3 and point towards the side window
•Close the air outlet vents 4
Warming up the inside of the vehicle as rapidly as possible
•Turn control dial to the right up to the stop
•Blower switch in position 3
•Turn the air distribution control into the position 
•Open the air outlet vents 3 and 4
•We recommend that you briefly switch on the recirculated air mode with the
pushbutton . The windows can steam up in this position however.
Heating the vehicle to a comfortable temperature
We recommend the following setting once the windows are no longer misted up
and the desired temperature has been reached:
•Control dial at the desired heat output
•Blower switch in position 2 or 3
•Turn the air distribution control into the position 
•Open the air outlet vents 3
•Close the air outlet vents 4
•Set the air distribution regulator as required between positions  and ,
if the windscreen gets misted up again.
Fresh air mode - ventilation
Non pre-warmed fresh air stream s through the air inlet nozzles 3 and 4 for the
following settings.
Recirculated air mode must not be switched on.
•Turn the control dial ⇒page 100, fig. 119 to the left up to the stop
•Blower switch in the desired position
•Turn the air distribution control into the position 
•Open air outlet vents 3 and 4 ⇒ page 102, fig. 120
AA
AB
AC
AA
AB
AC
AA
AB
AC
A1
AA
AB
AC
AC
AA
AB
AC
NKO A5 20 MR08.book Page 101 Wednesday, April 11, 2007 2:54 PM

Heating and air conditioning system105
Using the systemSafetyDriving TipsGeneral MaintenanceBreakdown assistanceTechnical Data
Note
•The whole heat output will be needed to unfrost the windscreen and side
windows. No warm air will be fed to the f ootwell. This can lead to restriction of the
heating comfort.
•The used air streams out through the air removal openings in the luggage
compartment.
•If the cooling system has not been switched on for a lengthy period, odours may
be produced at the evaporator because of deposits. Switch the cooling system on
at least once a month for approximately 5 minutes at the highest blower stage - also
during the cold season of the year - in order to remove such odours. Also open a
window for a short time.
•Please refer to the information regarding recirculated air mode ⇒page 106.
Set Climatic
Recommended settings of Climatic controls for the respective operating modes:
Defrosting the windscreen and side windows
•Put the control dial ⇒page 104, fig. 122 to the temperature selected as
usual by you (we recommend 22 °C); Climat ic puts automatically the heating to
maximum power, until the temperatur e selected by you is achieved.
•Blower switch in position 3
•Turn the air distribution control into the position 
•Open air outlet vents 3 ⇒ page 107, fig. 123 and point towards the side
window.
•Close the air outlet vents 4
Keeping winscreen demisted
We recommend that you use the following setting in cases where the windows are
misted up more than usual (e.g. when it is raining):
Blower switch in position 2
Turn the air distribution control into the position

Open air outlet vents 3 and point towards the side window
Close the air outlet vents 4
Switch on the cooling system by pressing button
Warming up the inside of the vehicle as rapidly as possible
•Put the control dial to the temperatur e selected as usual by you (we recom-
mend 22 °C); Climatic puts automatically the heating to maximum power, until the
temperature selected by you is achieved.
•Blower switch in position 3
•Turn the air distribution control into the position 
•Open the air outlet vents 3 and 4
•We recommend that you briefly switch on the recirculated air mode with the
pushbutton . The windows can steam up in this position however.
Heating the vehicle to a comfortable temperature
We recommend the following setting once the windows are no longer misted up
and the desired temperature has been reached:
•Control dial at the desired heat temperature
•Blower switch in position 2 or 3
•Turn the air distribution control into the position 
•Open the air outlet vents 3
•Close the air outlet vents 4
•Set the air distribution regulator as required between positions  and ,
if the windscreen gets misted up again.
Cooling down the inside of the vehicle as rapidly as possible
•close all windows and the sliding/tilting roof
•Put the control dial to the temperatur e selected as usual by you (we recom-
mend 22 °C); Climatic puts automatically the heating to maximum power, until the
temperature selected by you is achieved.
•Control dial in the position 4, supplies the interior of the car with fresh air.
•after brief airing, turn the co ntrol dial to the position 2 or 3
•Turn the air distribution control into the position 
AA
AB
AC
AB
AC
A1
AA
AB
AC
A3
AA
AB
AC
AC
AA
AB
AB
AC
NKO A5 20 MR08.book Page 105 Wednesday, April 11, 2007 2:54 PM