2007 SKODA FABIA light

Navigation43
Select menu field “Map type”
– Mark and confirm the menu field “ Map type”.
– Mark and confirm the desired map type in the sub-menu called up below. Then the map is displayed.
Location map - Display of the map detail with the current vehicle position.
Scale and alignment of the map are not changed.
Overview map - Display of the current vehicle position and the destina-
tion.
Destination map - Display of the destination. Scale and alignment of the
map are not changed.
Note
•If the overview map is called up in the auto zoom mode, the scale is
constantly adapted when approaching the destination.
•The selection bar is on the last selected setting when calling up the
sub-menu.
Select menu field “Move”
This function is intended for viewing the neighbouring map detail.
– Mark and confirm the menu field “ Move”. Then the map with
the crosshair is displayed.
If the crosshair is moved to the edge of the screen by turning the menu
knob , a neighbouring map detail is called up (see move crosshair
⇒ page 37).
Select menu field“Zoom setting”
– Mark and confirm the menu field “ Zoom setting” ⇒ fig. 34 .
– Press the menu knob in order to switch over between a precise or a less precise detail stage.
The active function is highlighted and marked with a triangular.
A18
Fig. 34 Zoom setting
Fig. 35 Auto zoom
A18
20.book Page 43 Tuesday, December 6, 2005 2:26 PM

Navigation
50
Switching on and off the dynamic navigation
– Press the button tailback function . The tailback menu
appears.
– Mark and confirm the menu field “ Route option”. The route
option menu is called up. Mark the menu field “ Dynamisa-
tion ”. – Press the menu knob to switch the dynamisation on or off.
The active condition is shown as highlighted and marked with a triangular.
The condition of the tailback function is shown in the symbol and map
display:
• dynamic navigation off
⇒page 50
• dynamic navigation on ⇒ page 50, route influence possible
In order to permanently store the set options, mark and confirm the menu
field “ route option ”.
Note
•By activating the dynamisation the other route options are preset as
fixed and cannot be changed.
•The dynamisation can also be switched on and off during an active
guidance.
•The function “GALA ” is switched off if the dynamisation is switched on.
•The navigation system always calculates a time optimized route; i.e. if
a tailback leads to detours and thus would mean a time loss the naviga-
tion system can under these circumstances guide through the tailback.
This depends on the length and type of the reported tailback and the
length of the possible detour.
Displays of the traffic reports
The traffic reports received via TMC can be displayed also as text
messages on the screen of your navigation system.
– Press the button tailback function . The tailback menu appears.
Fig. 43 Dynamic naviga-
tion - switched off
Fig. 44 Dynamic naviga-
tion - switched on
A16
A18


A16
20.book Page 50 Tuesday, December 6, 2005 2:26 PM

Navigation53
In the navigation basic menu you can select various basic settings for the
navigation system via the menu field “ Settings” ⇒ page 52, fig. 45 .
Select between the following possibilties:
Select language
- for the voice response:
•Czech
•German
•English (Imperial; distances are in miles and yards; speed is given in
miles per hour)
•English (Metrical; distances are in kilometres and meters; speed is
given in kilometres per hour)
•Span is h
•French
•Italian
Manual location
•You can manually enter the vehicle position with this function. This is
only necessary if the system cannot be positioned automatically, e.g.
when transporting the vehicle on a ferry or in a car sleeper rail. Perform
the entry via the menu sequence: Town - Street - Intersection.
Vo l u m e s e t u p
•in this menu the volume for the voice response can be set during the
guidance.
Show
•here you can select if the arrival time or the length of the trip to the
destination should be displayed in the map or symbol display.
Contrast
•You can set different contrast values for the day and night display. Setting clock
•the clock is automatically set via the GPS. The GPS system transmits
the universal time UTC This results in a time lag of two hours compared
to the middle european summer time and of one hour compared to the
winter time, which must be manually rectified. This is e.g. important for a
precise information about the arrival time at the destination.
Illumination
•You can select if the illumination of the screen should be performed
manually via the button or automatically when switching on the car
lights.
GPS viewer
•GPS (Global Positioning System, i.e. Global Positioning System) is a
navigation system of the Pentagon. It consists of 25 satellites, which circle
around the earth at an altitude of 21 000 km. Signals from at least three
satellites are received so that the system can determine the current
vehicle position.
The called up information screen gives information about:
•Number of available satellites
•Number of receiveable satellites
•current geographic vehicle position
Note
If less than three satellites are received, then appears the note “ The
geographic position cannot be determined at this moment in time ”.
A8
20.book Page 53 Tuesday, December 6, 2005 2:26 PM

Navigation55
Note
•You can also confirm the code by pressing the menu knob more
than two seconds.
Entry of an incorrect code number
After confirmation of the incorrect code number, the logo “ SAFE” flashes
in the numerical fields and then indicates also the entered code. The
message “1st code entered is wrong! ” is below the numerical fields.
Now the entire process can be repeated once again.
If once again an incorrect code number has been entered, the logo
“ SAFE ” is displayed in the numerical fields. The message “ Unit locked!”
is below the numerical fields. The unit is locked for approx. one hour, i.e.
it cannot be operated. After the elapse of one hour - the unit must remain
on and the key put into the ignition lock - the display lights up and the elec-
tronic lock can be cancelled as described beforehand.
The cycle - two attempts, blocked for an hour - furthermore applies.
Note
If the unit map gets lost with the code number, please contact your Škoda
Service Partner.
A18
20.book Page 55 Tuesday, December 6, 2005 2:26 PM

TV Tuner *57
2nd possibility:
– Turn the menu knob to the right (or left), in order to set the
next (or the previous ) channel.
For information the station and the belonging channel is indicated.
Store station
The six TV stations can be stored on the station buttons -
.
– Set the desired station with the button or the menu knob .
– If the desired station has to be displayed, the desired station button - must be pressed until there is a brief muting and
a signal tone cancels the storing.
You only have to touch the corresponding station button to call up the
stored station . The TV station belonging to it appears as long as it is in
its reception range.
Call up operator menu
TV operator menu:
•SCREEN - calls up a sub-menu, in which the brightness, contrast and
colour can be set.
•TELETEXT - here the video text pages can be called up.
•VIDEOSOURCE - switches from TV mode to video and vice versa.
•SETTINGS - calls up a sub-menu, in which the TV standard (video) is
selected.
Set screen
– Confirm the menu point “ SCREEN” in the operator menu by
pressing the menu knob . Following settings are possible:
Brightness, contrast, colour.
– To change to the setting mode press again the menu knob . Instead of the previous symbol appears an arrow
, the entry
is highlighted in colour.
– Select the desired value.
– Press the button , in order to take over the setting and to exit the menu.
Select Autosearch
If the Autosearch function is activated, the TV tuner always tries
to establish the best frequency of the selected TV station.
– Press the menu knob . The operator menu is indicated in the TV picture.
– Select and confirm the menu point “ SETTINGS”.
– Select the menu point “ AutoSearch” and press the menu
knob . The AutoSearch function is switched on (or switched
off).
A18
16
A12
A2
A18
16
A18
A18
A9
A18
A18
20.book Page 57 Tuesday, December 6, 2005 2:26 PM

TV Tuner *
58
– Press the button , in order to take over the new setting.
Select TV standard
– Press the menu knob . The operator menu is indicated in the TV picture.
– Select and confirm the menu point “ SETTINGS”. The current
standard is displayed in the highlighted lettering.
– Select and confirm the menu point “ Standard”. Now carry out
the settings.
– Turn the menu button , in order to set the desired TV standard.
– Press the button , in order to take over the new setting.
Note
An incorrect setting of the TV standard can lead to a distortion of the TV
picture.
Call up video text
– Press the menu knob in the TV mode. The menu SELECT appears. – Select and confirm the menu point “
VIDEOTEXT” in the oper-
ator menu. If the current station transmits video text data, the
panel 100 appears in the full picture mode.
– Press the button , in order to exit the video text mode.
Note
•The display of the video text panel can be changed with the button for
automatic station finding .
•The text panel is shown in the following order - full picture - upper half
picture - lower half picture - full picture by repetitively pressing the
button.
Call up video text panel
– Turn the menu knob to the left or right, in order to reach the desired video text panel in stages.
– The panel number can be changed by turning the menu knob .
– Press the menu knob in order to confirm the selection, the marking changes to the next digit. Continue with the entry as
described. If the last digit was confirmed, the panel is being
searched and displayed.
Note
If you wish to call up a specific board, press the menu knob in order to
change to the entry mode. An entry bar appears, the first digit of the three-
digit number is 1.
A9
A18
A18
A9
A18
A9
 
A18
A18
A18
A18
20.book Page 58 Tuesday, December 6, 2005 2:26 PM