2007 SATURN VUE open hood

Engine Coolant Heater
Your vehicle may have this feature. In very cold
weather, 0°F (−18°C) or colder, the engine coolant
heater can provide easier starting and better
fuel economy during engine warm-up. Usually,
the coolant heater should be plugged in a
minimum of four hours prior to starting your
vehicle. At temperatures above 32°F (0°C), use
of the coolant heater is not required. Your vehicle
may also have an internal thermostat in the
plug end of the cord. This will prevent operation of
the engine coolant heater when the temperature
is at or above 0°F (−18°C) as noted on the cord.
To Use the Engine Coolant Heater
1. Turn off the engine.
2. Open the hood and unwrap the electrical
cord. The engine coolant heater cord is
located near the air cleaner box on the
passenger side of the engine compartment.
SeeEngine Compartment Overview on
page 314for more information on location.
3. Plug the cord into a normal, grounded
110-volt AC outlet.
{CAUTION:
Plugging the cord into an ungrounded
outlet could cause an electrical shock.
Also, the wrong kind of extension cord
could overheat and cause a re. You
could be seriously injured. Plug the cord
into a properly grounded three-prong
110-volt AC outlet. If the cord will not
reach, use a heavy-duty three-prong
extension cord rated for at least 15 amps.
4. Before starting the engine, be sure to unplug
and store the cord as it was before to keep it
away from moving engine parts. If you do
not, it could be damaged.
How long should you keep the coolant heater
plugged in? The answer depends on the outside
temperature, the kind of oil you have, and some
other things. Instead of trying to list everything here,
we ask that you contact your retailer in the area
where you will be parking your vehicle. The
dealer/retailer can give you the best advice
for that particular area.
113
ProCarManuals.com

Hood Release
To open the hood, do the following:
1. Pull the handle with
this symbol on it.
It is located
under the instrument
panel on the
driver’s side of
the vehicle.
2. Then go to the front of the vehicle and lift up
on the secondary hood release lever.
3. Lift the hood.
Before closing the hood, be sure all the ller caps
are on properly. Then pull the hood down and
close it rmly.
313
ProCarManuals.com

Engine Compartment Overview
When you open the hood on the 2.2L L4 engine, you will see the following:
314
ProCarManuals.com

When you open the hood on the 3.5L V6 engine, you will see the following:
316
ProCarManuals.com

If Steam Is Coming From Your Engine
{CAUTION:
Steam from an overheated engine can
burn you badly, even if you just open the
hood. Stay away from the engine if you
see or hear steam coming from it. Just
turn it off and get everyone away from the
vehicle until it cools down. Wait until
there is no sign of steam or coolant
before you open the hood.
If you keep driving when your engine is
overheated, the liquids in it can catch re.
You or others could be badly burned.
Stop your engine if it overheats, and get
out of the vehicle until the engine is cool.
Notice:If your engine catches re because
you keep driving with no coolant, your vehicle
can be badly damaged. The costly repairs
would not be covered by your warranty.
If No Steam Is Coming From
Your Engine
If you get an engine overheat warning, but see
or hear no steam, the problem may not be too
serious. Sometimes the engine can get a little too
hot when you:
Climb a long hill on a hot day.
Stop after high-speed driving.
Idle for long periods in traffic.
Tow a trailer.
If you get the overheat warning with no sign of
steam, try this for a minute or so:
1. If you have an air conditioner and it is on,
turn it off.
2. Turn on your heater to full hot at the highest
fan speed and open the windows as
necessary.
3. Try to minimize engine load. If you are in a
traffic jam, shift to NEUTRAL (N); otherwise,
shift to the highest gear possible while driving.
335
ProCarManuals.com

Notice:If you leave your radio or other
accessories on during the jump starting
procedure, they could be damaged. The repairs
would not be covered by your warranty.
Always turn off your radio and other
accessories when jump starting your vehicle.
3. Turn off the ignition on both vehicles.
Unplug unnecessary accessories plugged into
the cigarette lighter or the accessory power
outlet. Turn off the radio and all lamps that are
not needed. This will avoid sparks and help
save both batteries. And it could save
the radio!
4. Open the hood on the other vehicle and
locate the positive (+) and negative (−)
terminal locations on that vehicle.
Open the hood on your vehicle and nd the
remote positive (+) and remote negative (−)
jump starting terminals.A. Remote Positive
B. Remote Negative
Vehicles equipped with the 2.2L L4 engine,
the remote positive (+) terminal is located
in the engine compartment on the driver’s side
of the vehicle, on the underhood fuse block.
SeeEngine Compartment Overview on
page 314for more information on location.
Access the remote positive (+) terminal
by removing the fuse block cover.
The remote negative (−) terminal is the lift
hook, which is located towards the rear of the
engine on the driver’s side.
2.2L L4 Engine
349
ProCarManuals.com

A. Remote Negative
B. Positive Terminal
Vehicle equipped with the 3.5L V6 engine, the
positive (+) terminal is located in the engine
compartment on the driver’s side of the vehicle
on the battery. The negative (−) terminal is
located in the engine compartment on
the driver’s side of the vehicle. SeeEngine
Compartment Overview on page 314for more
information on location.After unsnapping and opening the black cap
on the positive (+) terminal on the top of
the battery, clamp the jumper cable to
the terminal.
Place the negative (-) jumper cable clamp on
the nut on the end of the engine.
{CAUTION:
An electric fan can start up even when the
engine is not running and can injure you.
Keep hands, clothing and tools away from
any underhood electric fan.3.5L V6 Engine
350
ProCarManuals.com

To adjust the vertical aim:
1. Open the hood. SeeHood Release on
page 313for more information.
2. Locate the aim dot on the lens of the
low-beam headlamp.
3. Measure the distance from the ground to the
aim dot on the low-beam headlamp. Record
the distance.4. At the wall measure from the ground
upward (A) to the recorded distance
from Step 3 and mark it.
5. Draw or tape a horizontal line (B) on the wall
the width of the vehicle at the height of the
mark in Step 4.
Notice:Do not cover a headlamp to improve
beam cut-off when aiming. Covering a
headlamp may cause excessive heat build-up
which may cause damage to the headlamp.
6. Turn on the low-beam headlamps and place a
piece of cardboard or equivalent in front of the
headlamp not being adjusted. This allows
only the beam of light from the headlamp
being adjusted to be seen on the at surface.
356
ProCarManuals.com