2007 SATURN VUE oil dipstick

A. Engine Air Cleaner/Filter. SeeEngine Air
Cleaner/Filter on page 324.
B. Engine Oil Dipstick. See “Checking Engine Oil”
underEngine Oil on page 318.
C. Engine Oil Fill Cap. See “When to Add Engine
Oil” underEngine Oil on page 318.
D. Remote Negative (−) Terminal. SeeJump
Starting on page 348.
E. Brake/Clutch Cylinder Fluid. SeeBrakes on
page 343andHydraulic Clutch on page 331.F. Underhood Fuse Block. SeeUnderhood Fuse
Block on page 411.
G. Battery. SeeBattery on page 347.
H. Remote Positive (+) Terminal. SeeJump
Starting on page 348.
I. Engine Coolant Surge Tank. See “Checking
Coolant” underEngine Coolant on page 331.
J. Windshield Washer Fluid Reservoir. See
“Adding Washer Fluid” underWindshield
Washer Fluid on page 341.
315
ProCarManuals.com

A. Engine Air Cleaner/Filter. SeeEngine Air
Cleaner/Filter on page 324.
B. Engine Oil Dipstick (Out of View). See
“Checking Engine Oil” underEngine Oil on
page 318.
C. Engine Oil Fill Cap (Out of View). See “When
to Add Engine Oil” underEngine Oil on
page 318.
D. Remote Negative (−) Terminal. SeeJump
Starting on page 348.
E. Brake Fluid Reservoir. SeeBrakes on
page 343.F. Battery. SeeBattery on page 347.
G. Underhood Fuse Block. SeeUnderhood Fuse
Block on page 411.
H. Remote Positive (+) Terminal (Out of View).
SeeJump Starting on page 348.
I. Engine Coolant Surge Tank. See “Checking
Coolant” underEngine Coolant on page 331.
J. Windshield Washer Fluid Reservoir. See
“Adding Washer Fluid” underWindshield
Washer Fluid on page 341.
317
ProCarManuals.com

Engine Oil
Checking Engine Oil
It is a good idea to check the engine oil every time
you get fuel. In order to get an accurate reading,
the oil must be warm and the vehicle must be
on level ground.
The engine oil dipstick handle is a yellow loop for
the 2.2L L4 engine and an orange loop for the
3.5L V6 engine. SeeEngine Compartment
Overview on page 314for the location of the
engine oil dipstick.
1. Turn off the engine and give the oil several
minutes to drain back into the oil pan. If you
do not do this, the oil dipstick might not
show the actual level.
2. Pull out the dipstick and clean it with a paper
towel or cloth, then push it back in all the
way. Remove it again, keeping the tip down,
and check the level.
When to Add Engine Oil
2.2L L4 Engine
3.5L V6 Engine
318
ProCarManuals.com

If the oil is below the MIN (minimum) mark for the
2.2L L4 engine or below the lower mark (B) for
the 3.5L V6 engine, you need to add at least
one quart/liter of oil. But you must use the right
kind. This section explains what kind of oil to use.
For engine oil crankcase capacity, seeCapacities
and Specications on page 414.
Notice:Do not add too much oil. If the engine
has so much oil that the oil level gets above
the upper mark that shows the proper
operating range, the engine could be damaged.
SeeEngine Compartment Overview on page 314
for the location of the engine oil ll cap.
Be sure to add enough oil to put the level
somewhere in the proper operating range.
Push the dipstick all the way back in when you
are through.
2.2L L4 Engine3.5L V6 Engine
319
ProCarManuals.com

Automatic Transaxle Fluid
(3.5L V6 Engine)
When to Check and Change Automatic
Transaxle Fluid
A good time to check your automatic transaxle
uid level is when the engine oil is changed.
Change the uid at the intervals listed inAdditional
Required Services on page 423, and be sure to
use the transaxle uid listed inRecommended
Fluids and Lubricants on page 432.
How to Check Automatic
Transaxle Fluid
Because this operation can be a little difficult, you
may choose to have this done at your retailer’s
service department.
If you do it yourself, be sure to follow all the
instructions here, or you could get a false reading
on the dipstick.Notice:Too much or too little uid can damage
the transaxle. Too much can mean that some of
the uid could come out and fall on hot engine
or exhaust system parts, starting a re. Too
little uid could cause the transaxle to overheat.
Be sure to get an accurate reading if you check
the transaxle uid.
Wait at least 30 minutes before checking the
transaxle uid level if you have been driving:
When outside temperatures are
above 90°F (32°C).
At high speed for quite a while.
In heavy traffic — especially in hot weather.
While pulling a trailer.
To get the right reading, the uid should be at
normal operating temperature, which is 180°F to
200°F (82°C to 93°C).
Get the vehicle warmed up by driving about
15 miles (24 km) when outside temperatures are
above 50°F (10°C). If it is colder than 50°F (10°C),
you may have to drive longer.
328
ProCarManuals.com