2007 SATURN VUE tow

2. Press and hold the on/off button until a zone
number appears in the display. The compass
is now in zone mode.
3. Keep pressing the on/off button until the
desired zone number appears in the display.
Release the button. After approximately four
seconds of inactivity, the new zone number
will be locked in and the comp/temp display
will return.
Cleaning the Mirror
When cleaning the mirror, use a paper towel or
similar material dampened with glass cleaner.
Do not spray glass cleaner directly on the mirror
as that may cause the liquid cleaner to enter
the mirror housing.
Outside Power Mirrors
The outside power
mirror controls are
located on the driver’s
side of the vehicle
next to the shift lever.
Move the selector switch to the left or right to
choose the mirror to be adjusted; then press the
four-way control pad to adjust the direction of
the mirror.
127
ProCarManuals.com

Storage Areas
Glove Box
To open the glove box, lift up on the lever.
Cupholder(s)
Your vehicle has a removable cupholder liner
and cupholder located inside the center console
storage area. To access, pull the cover towards
the rear of the vehicle. To remove the liner, pull it
out of the cupholder. To replace, push the liner
back in. To remove the cupholder, push the tab
in near the passenger’s seat and pull straight
up. To replace, slide the two tabs at the rear of
the cupholder into the slots at the rear of the
center console and push the cupholder gently
into place. There is additional storage underneath
the cupholders. There are two more cupholders
located at rear of the center console. Push
the button to access.
Floor Console Storage Area
Your vehicle may have a oor console storage
area. Push the button to open.
Center Console Storage Area
Your vehicle has a center console storage area.
To access, slide the cover back towards the rear
of the vehicle. It is equipped with two accessory
power outlets. One is located inside the storage
area and another hidden under the cupholders.
There is a hole in the storage area for a cellphone
wire to be routed through.
Cargo Area
Your vehicle has a cargo area organizer, which
is located in the rear of the vehicle. This storage
space is designed to hold small items and includes
integrated storage bins.
132
ProCarManuals.com

5. Turn the center divider rearward and snap it
into the panel lid.
6. Reverse the above steps to stow the dividers
and close the cargo organizer.
Push rmly on the rear panel lid to engage
the latch of the organizer.
Roof Rack System
Your vehicle may be equipped with a roof rack
system. To adjust the crossrails, turn both knobs
on each side of the crossrail counterclockwise
until it moves freely. Once the crossrail is in place,
turn both knobs on each of side of the crossrail
clockwise until it is secure.
134
ProCarManuals.com

Headlamp High/Low-Beam Changer
To change the headlamps from low beam to
high or high beam to low, pull the turn signal lever
all the way towards you. Then release it.
When the high beams
are on, this light on
the instrument panel
cluster will also be on.
Flash-to-Pass
This feature lets you use your high-beam
headlamps to signal a driver in front of you
that you want to pass.
To ash the high beams from low beam, pull
the turn signal/multifunction lever all the way
towards you. Then release it.
Windshield Wipers
Be sure to clear ice and snow from the wiper blades
before using them. If the wiper blades are frozen to
the windshield, gently loosen or thaw them. If the
blades do become damaged, install new blades
or blade inserts. SeeWindshield Wiper Blade
Replacement on page 364.
Heavy snow or ice can overload the wiper motor.
A circuit breaker will stop the motor until it cools
down. Clear away snow or ice to prevent an
overload.
United States
144
ProCarManuals.com

The lever on the right side of the steering column
operates the windshield wipers. Push up or
pull down on the lever to place it in one of the
following positions.
MIST or
8(Mist):Pull the lever down and
release it for a single wiping cycle. The lever will
return to its original position. For more cycles, hold
the lever down before releasing it.
OFF or
9(Off):Move the lever to this position
to turn off the wipers.
INT or
&(Intermittent):Move the lever to this
position to set a delay between wipes. To set for a
shorter or longer delay between wipes, turn theband with the arrow pointing to the
numbers (1, 2, or 3). Select 3 for the most
frequent movement; select 1 for the least frequent.
LO or
OO(Low):Move the lever to this
position for slow, steady wiping cycles.
HI or
OOOO(High):Move the lever to this
position for rapid wiping cycles.
Windshield Washer
{CAUTION:
In freezing weather, do not use your
washer until the windshield is warmed.
Otherwise the washer uid can form ice
on the windshield, blocking your vision.
Pull the windshield wiper lever toward you to
operate the windshield wipers. Washer uid will
squirt onto the windshield and the wipers will
run for a few cycles to clear the windshield.
For more wash cycles, pull the lever toward
you and hold it there.
Canada
145
ProCarManuals.com

Brake System Warning Light
Your vehicle’s hydraulic brake system is divided
into two parts. If one part is not working, the
other part can still work and stop you. For good
braking, though, you need both parts working well.
If the brake system warning light comes on,
there is a brake problem. Have your brake system
inspected right away.
The brake light is located in the instrument
panel cluster.
This light should come on briey when you turn
the ignition key to RUN. If it does not come
on then, have it xed so it will be ready to
warn you if there is a problem.
When the ignition is on, the brake light will come
on when you set your parking brake. The light
will stay on if your parking brake does not releasefully. A chime will also sound if the parking brake
is not fully released and the vehicle is moving.
If it stays on after your parking brake is fully
released, it means you have a brake problem.
The brake light will also come on to indicate a
low brake uid level. SeeBrakes on page 343
for more information.
If the light comes on while you are driving, pull off
the road and stop carefully. You may notice that the
pedal is harder to push or the pedal may go closer
to the oor. It may take longer to stop. If the light is
still on, have the vehicle towed for service. See
Towing Your Vehicle on page 284.
{CAUTION:
Your brake system may not be working
properly if the brake system warning light
is on. Driving with the brake system
warning light on can lead to an accident.
If the light is still on after you have pulled
off the road and stopped carefully, have
the vehicle towed for service.
United StatesCanada
170
ProCarManuals.com

Anti-Lock Brake System
Warning Light
If your vehicle has anti-lock brakes, the anti-lock
brake system (ABS) warning light will come
on briey, as a check, when you start your vehicle.
If it does not, have your vehicle serviced so that
the light works properly when it needs to.
The ABS light is located
in the instrument panel
cluster, to the left of
the engine coolant
temperature gage.
If the light stays on longer than a few seconds
after you start your engine, or comes on and stays
on while you are driving, try resetting the system.To reset the system, do the following:
1. If you are driving, pull over when it is safe
to do so.
2. Be sure the vehicle is in PARK (P).
3. Turn off the ignition.
4. Then restart the engine.
If the light remains on after resetting the system
or comes on again while driving, your vehicle
needs service. If the ABS light is on, but the
regular brake system warning light is not on, the
anti-lock brakes are not working properly, but
the regular brakes are still functioning. Have your
vehicle serviced right away. If both brake lights
are on, you do not have anti-lock brakes, and
there’s a problem with your regular brakes as well.
Have your vehicle towed for service. SeeTowing
Your Vehicle on page 284.
The anti-lock brake system warning light should
come on briey when you turn the ignition key to
RUN. If the light does not come on then, have it
xed so it will be ready to warn you if there is a
problem.
171
ProCarManuals.com

This light should come on, as a check to show
you it is working, when the ignition is on and
the engine is not running. If the light does
not come on, have it repaired. This light will also
come on during a malfunction in one of two ways:
Light Flashing— A misre condition has
been detected. A misre increases vehicle
emissions and may damage the emission
control system on your vehicle. Diagnosis
and service may be required.
Light On Steady— An emission control
system malfunction has been detected on
your vehicle. Diagnosis and service may be
required.
If the Light Is Flashing
The following may prevent more serious damage
to your vehicle:
Reducing vehicle speed
Avoiding hard accelerations
Avoiding steep uphill grades
If you are towing a trailer, reduce the amount of
cargo being hauled as soon as it is possibleIf the light stops ashing and remains on steady,
see “If the Light Is On Steady” following.
If the light continues to ash, when it is safe to do
so, stop the vehicle. Find a safe place to park
your vehicle. Turn the key off, wait at least
10 seconds and restart the engine. If the light
remains on steady, see “If the Light Is On Steady”
following. If the light is still ashing, follow the
previous steps, and see your retailer for service
as soon as possible.
If the Light Is On Steady
You may be able to correct the emission system
malfunction by considering the following:
Did you recently put fuel into your vehicle?
If so, reinstall the fuel cap, making sure to fully
install the cap. SeeFilling the Tank on page 309.
The diagnostic system can determine if the fuel cap
has been left off or improperly installed. A loose or
missing fuel cap will allow fuel to evaporate into
the atmosphere. A few driving trips with the cap
properly installed should turn the light off.
176
ProCarManuals.com