2007 SATURN RELAY spare wheel

Tires............................................................ 462
Tire Sidewall Labeling............................... 463
Tire Terminology and Denitions............... 466
Ination - Tire Pressure............................. 469
High-Speed Operation............................... 471
Tire Inspection and Rotation...................... 472
When It Is Time for New Tires.................. 473
Buying New Tires...................................... 474
Different Size Tires and Wheels................ 476
Uniform Tire Quality Grading..................... 477
Wheel Alignment and Tire Balance............ 478
Wheel Replacement.................................. 478
Tire Chains............................................... 480
Accessory Inator...................................... 480
If a Tire Goes Flat.................................... 483
Changing a Flat Tire................................. 484
Removing the Spare Tire and Tools.......... 485
Removing the Flat Tire and Installing
the Spare Tire....................................... 488
Secondary Latch System........................... 495
Storing a Flat or Spare Tire and Tools...... 497
Compact Spare Tire.................................. 500Appearance Care........................................ 501
Cleaning the Inside of Your Vehicle.......... 501
Fabric/Carpet............................................. 502
Leather...................................................... 503
Instrument Panel, Vinyl, and Other
Plastic Surfaces..................................... 504
Care of Safety Belts.................................. 504
Weatherstrips............................................ 504
Washing Your Vehicle............................... 505
Cleaning Exterior Lamps/Lenses................ 505
Finish Care............................................... 505
Windshield, Backglass, and
Wiper Blades......................................... 506
Aluminum Wheels...................................... 507
Tires......................................................... 507
Sheet Metal Damage................................. 508
Finish Damage.......................................... 508
Underbody Maintenance............................ 508
Chemical Paint Spotting............................ 508
Vehicle Care/Appearance Materials............ 509
Section 5 Service and Appearance Care
410
ProCarManuals.com

Tire Inspection and Rotation
Tires should be rotated every 5,000 to 8,000 miles
(8 000 to 13 000 km).
Any time you notice unusual wear, rotate your
tires as soon as possible and check wheel
alignment. Also check for damaged tires or wheels.
SeeWhen It Is Time for New Tires on page 473
andWheel Replacement on page 478for
more information.
The purpose of regular rotation is to achieve
more uniform wear for all tires on the vehicle.
The rst rotation is the most important. See
Scheduled Maintenance on page 522.When rotating your tires, always use the correct
rotation pattern shown here.
Do not include the compact spare tire in your tire
rotation.
After the tires have been rotated, adjust the front
and rear ination pressures as shown on the
Tire and Loading Information label.
Make certain that all wheel nuts are properly
tightened. See “Wheel Nut Torque” under
Capacities and Specications on page 518.
472
ProCarManuals.com

{CAUTION:
Mixing tires could cause you to lose
control while driving. If you mix tires of
different sizes, brands, or types (radial
and bias-belted tires), the vehicle may
not handle properly, and you could have
a crash. Using tires of different sizes,
brands, or types may also cause damage
to your vehicle. Be sure to use the
correct size, brand, and type of tires on
all wheels. It is all right to drive with
your compact spare temporarily, as it
was developed for use on your vehicle.
SeeCompact Spare Tire on page 500.
{CAUTION:
If you use bias-ply tires on your vehicle,
the wheel rim anges could develop
cracks after many miles of driving. A tire
and/or wheel could fail suddenly, causing
a crash. Use only radial-ply tires with the
wheels on your vehicle.
If you must replace your vehicle’s tires with
those that do not have a TPC Spec number,
make sure they are the same size, load range,
speed rating, and construction type (radial
and bias-belted tires) as your vehicle’s
original tires.
Your vehicle’s original equipment tires are listed
on the Tire and Loading Information Label.
This label is attached to the vehicle’s center pillar
(B-pillar). SeeLoading Your Vehicle on page 391,
for more information about the Tire and Loading
Information Label and its location on your vehicle.
475
ProCarManuals.com

When your vehicle has a at tire, use the following
example as a guide to assist you in the placement
of wheel blocks.
The following information will tell you next how to
use the jack and change a tire.Removing the Spare Tire and Tools
The tools needed to remove the spare tire are
located in the storage compartment at the rear of
the vehicle, on the passenger’s side.
To remove the tools, do the following:
1. Open the liftgate. SeeLiftgate on page 128
for more information.
2. Remove the convenience net, if the vehicle
has one.
485
ProCarManuals.com

To remove the compact spare tire, do the following:
A. Hoist Shaft
B. Hoist Assembly
C. Retainer
D. Compact Spare TireE. Extension
(Chisel End)
F. Folding Wrench
1. Attach the folding wrench (F) to the
extension (E) and insert the chisel end on
an angle through the hole in the rear bumper
and into the hoist shaft (A).2. Turn the folding wrench counterclockwise to
lower the compact spare tire (D) to the
ground. Continue to turn the wrench so the
compact spare tire can be pulled out from
under the vehicle.
3. Tilt the retainer at the end of the cable to
remove the compact spare tire, so it can
be pulled up through the wheel opening.
The hoist is used to store a full-size or a at
road tire under the vehicle. SeeStoring a
Flat or Spare Tire and Tools on page 497
for more information.
4. Remove the compact spare tire from the cable.
487
ProCarManuals.com

If the compact spare tire will not lower, check
under the vehicle to see if the tire is hanging
loose and the cable end and spring under
the wheel plate are missing. If so, the secondary
latch system is engaged. SeeSecondary Latch
System on page 495.
To continue changing the at tire, see
Removing the Flat Tire and Installing the
Spare Tire on page 488.Removing the Flat Tire and
Installing the Spare Tire
Your vehicle may have aluminum wheels. If so,
you will see exposed stainless steel wheel
nuts. Use the wheel wrench to loosen all of the
wheel nuts. Do not remove them yet. Or, your
vehicle may have steel wheel covers. To remove
the wheel covers and wheel nut caps, loosen
the plastic nut caps with the wheel wrench in a
counterclockwise direction. If needed, you
can nish loosening with your ngers. The plastic
nut caps will not come off. Use the at end of
the wheel wrench and pry along the edge of the
cover until it comes off. The edge of the wheel
cover could be sharp, so do not try to remove it
with your bare hands. Do not drop the cover or lay
it face down, as it could become scratched or
damaged. Once you have removed the wheel
cover, use the following procedure to remove the
at tire and install the spare tire.
488
ProCarManuals.com

A. Front Location
B. Rear Location
2. Near each wheel, there is a notch (A and B)
in the vehicle’s frame, inboard of the rocker
molding. Position the jack and raise the
jack head until it ts rmly into the notch in
the vehicle’s frame nearest the at tire.
Do not raise the vehicle yet.
3. Put the compact spare tire near you.
{CAUTION:
Getting under a vehicle when it is jacked
up is dangerous. If the vehicle slips off
the jack you could be badly injured or
killed. Never get under a vehicle when it
is supported only by a jack.
{CAUTION:
Raising your vehicle with the jack
improperly positioned can damage the
vehicle and even make the vehicle fall.
To help avoid personal injury and vehicle
damage, be sure to t the jack lift head
into the proper location before raising the
vehicle.
490
ProCarManuals.com

4. Attach the folding wrench (A) to the jack (B),
and turn the wrench clockwise to raise the
jack head approximately 3 inches (7.6 cm).5. Raise the vehicle by turning the folding
wrench clockwise in the jack. Raise the
vehicle far enough off the ground so there
is enough room for the compact spare tire
to t under the wheel well.
491
ProCarManuals.com